2005 INFINITI FX35 brake sensor

TROUBLE DIAGNOSIS AT-55
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
6. Start the engine, then measure the line pressure at both idle and
the stall speed.
CAUTION:

Keep the brake pedal pressed all the way down during
measurement.

When measuring the line pressure at the stall speed,
refer to AT- 5 2 , "
STALL TEST" .
7. After the measurements are complete, install the oil pressure detection plug and tighten to the specified torque.
CAUTION:

Do not reuse the O-ring.

Apply ATF to the O-ring.
Line Pressure
Judgement of Line Pressure Test
:7.3 N·m (0.74 kg-m, 65 in-lb)SAT493G
Engine speed Line pressure [kPa (kg/cm
2 , psi)]
“R” position “D”, “M” positions
At idle speed 425 - 465 (4.3 - 4.8, 62 - 67) 379 - 428 (3.9 - 4.4, 55 - 62)
At stall speed 1,605 - 1,950 (16.4 - 19.9, 233 - 283) 1,310 - 1,500 (13.4 - 15.3, 190 - 218)
Judgement Possible cause
Idle speed Low for all positions
(“P”, “R”, “N”, “D”,
“M”) Possible causes include malfunctions in the pressure supply system and low oil pump output.
For example

Oil pump wear

Pressure regulator valve or plug sticking or spring fatigue

Oil strainer
oil pump
pressure regulator valve passage oil leak

Engine idle speed too low
Only low for a spe-
cific position Possible causes include an oil pressure leak in a passage or device related to the position after
the pressure is distributed by the manual valve.
High Possible causes include a sensor malfunction or malfunction in the line pressure adjustment func-
tion.
For example

Accelerator pedal position signal malfunction

ATF temperature sensor malfunction

Line pressure solenoid malfunction (sticking in OFF state, filter clog, cut line)

Pressure regulator valve or plug sticking

AT-64
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
Symptom ChartACS0080Q

The diagnostics item numbers show the sequence for inspection. Check in order from Item 1.

Overhaul and check inside the A/T only if A/T fluid condition is NG. Refer to AT- 5 2 , "A/T Fluid Condition
Check" .
No. Items Symptom Condition Diagnostic Item Reference
page
1 Shift
Shock Large shock. (“N”
→
“D” position)
Refer to AT-197,
"Large Shock (“N” to
“D” Position)" . ON vehicle 1. Engine idle speed
EC-83
(for
VQ35DE)
or EC-774

(for
VK45DE)
2. Engine speed signal AT- 1 2 3
3. Accelerator pedal position sensorAT- 1 3 3
4. Control linkage adjustmentAT- 2 3 5
5. A/T fluid temperature sensorAT- 1 3 6
6. ATF pressure switch 1 and front brake solenoid valve AT- 1 7 5,
AT- 1 5 4
7. CAN communication line AT- 1 0 6
8. A/T fluid level and state AT- 5 2
9. Line pressure testAT- 5 4
10. Control valve with TCMAT- 2 4 3
OFF vehicle 11. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18, "Cross-Sectional View (2WD Models)" or AT- 1 9 , "Cross-
Sectional View (AWD Models)" ) AT- 2 9 0
2
Shock is too large
when changing D1 →
D
2 or M1 → M2 . ON vehicle 1. Accelerator pedal position sensor
AT- 1 3 3
2. Control linkage adjustmentAT- 2 3 5
3. ATF pressure switch 5 and direct clutch solenoid valve AT- 1 7 9,
AT- 1 5 8
4. CAN communication line AT- 1 0 6
5. Engine speed signalAT- 1 2 3
6. Turbine revolution sensorAT- 1 4 1
7. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
8. A/T fluid level and state AT- 5 2
9. Control valve with TCMAT- 2 4 3
OFF vehicle 10. Direct clutch AT- 3 2 6

TROUBLE DIAGNOSIS AT-65
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
3
Shift
Shock Shock is too large
when changing D2 →
D
3 or M2 → M3 . ON vehicle 1. Accelerator pedal position sensor
AT-133
2. Control linkage adjustmentAT-235
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valve AT-181,
AT-162
4. CAN communication line AT-106
5. Engine speed signalAT-123
6. Turbine revolution sensorAT-141
7. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143
8. A/T fluid level and state AT- 5 2
9. Control valve with TCMAT-243
OFF vehicle 10. High and low reverse clutch AT-323
4 Shock is too large
when changing D3 →
D
4 or M3 → M4 . ON vehicle 1. Accelerator pedal position sensor
AT-133
2. Control linkage adjustmentAT-235
3. ATF pressure switch 3 and input clutch solenoid valve AT-177,
AT-150
4. CAN communication line AT-106
5. Engine speed signalAT-123
6. Turbine revolution sensorAT-141
7. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143
8. A/T fluid level and state AT- 5 2
9. Control valve with TCMAT-243
OFF vehicle 10. Input clutch AT-313
5 Shock is too large
when changing D4 →
D
5 or M4 → M5 . ON vehicle 1. Accelerator pedal position sensor
AT-133
2. Control linkage adjustmentAT-235
3. ATF pressure switch 1 and front brake solenoid valve AT-175,
AT-154

4. CAN communication line AT-106
5. Engine speed signalAT-123
6. Turbine revolution sensorAT-141
7. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143
8. A/T fluid level and state AT- 5 2
9. Control valve with TCMAT-243
OFF vehicle 10. Front brake (brake band)
AT-27811. Input clutchAT-313
No. Items Symptom Condition Diagnostic Item Reference
page

AT-66
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
6
Shift
Shock Shock is too large for
downshift when accel-
erator pedal is
pressed. ON vehicle 1. Accelerator pedal position sensor
AT- 1 3 3
2. Control linkage adjustmentAT- 2 3 5
3. CAN communication lineAT- 1 0 6
4. Engine speed signalAT- 1 2 3
5. Turbine revolution sensorAT- 1 4 1
6. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
7. A/T fluid level and state AT- 5 2
8. Control valve with TCMAT- 2 4 3
OFF vehicle 9. Front brake (brake band)
AT- 2 7 810. Input clutch AT- 3 1 3
11. High and low reverse clutchAT- 3 2 3
12. Direct clutchAT- 3 2 6
7 Shock is too large for
upshift when acceler-
ator pedal is released. ON vehicle 1. Accelerator pedal position sensor
AT- 1 3 3
2. Control linkage adjustmentAT- 2 3 5
3. Engine speed signalAT- 1 2 3
4. CAN communication lineAT- 1 0 6
5. Turbine revolution sensorAT- 1 4 1
6. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
7. A/T fluid level and state AT- 5 2
8. Control valve with TCMAT- 2 4 3
OFF vehicle 9. Front brake (brake band)
AT- 2 7 810. Input clutch AT- 3 1 3
11. High and low reverse clutch AT- 3 2 3
12. Direct clutch AT- 3 2 6
8 Shock is too large for
lock-up. ON vehicle 1. Accelerator pedal position sensor
AT- 1 3 3
2. Control linkage adjustmentAT- 2 3 5
3. Engine speed signalAT- 1 2 3
4. CAN communication lineAT- 1 0 6
5. Turbine revolution sensorAT- 1 4 1
6. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
7. Torque converter clutch solenoid valve AT- 1 2 5
8. A/T fluid level and state AT- 5 2
9. Control valve with TCMAT- 2 4 3
OFF vehicle 10. Torque converter AT- 2 9 0
No. Items Symptom Condition Diagnostic Item Reference
page

TROUBLE DIAGNOSIS AT-67
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX9 Shift
Shock Shock is too large
during engine brake. ON vehicle
1. Accelerator pedal position sensor
AT-133
2. Control linkage adjustmentAT-235
3. CAN communication lineAT-106
4. A/T fluid level and state AT- 5 2
5. Control valve with TCMAT-243
OFF vehicle 6. Front brake (brake band)
AT-2787. Input clutch AT-313
8. High and low reverse clutchAT-323
9. Direct clutch AT-326
10
No Up
Shift Gear does not change
from D
1 → D2 or from
M
1 → M2 .
Refer to AT-208, "
A/T
Does Not Shift: D1 →
D2" . ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143
3. ATF pressure switch 5 and direct clutch solenoid valve AT-179,
AT-158
4. Line pressure test AT- 5 4
5. CAN communication lineAT-106
6. Control valve with TCMAT-243
OFF vehicle 7. Direct clutch AT-326
11 Gear does not change
from D
2 → D3 or from
M
2 → M3 .
Refer to AT-210, "
A/T
Does Not Shift: D2 →
D3" . ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valve AT-181,
AT-162
4. Line pressure test AT- 5 4
5. CAN communication lineAT-106
6. Control valve with TCMAT-243
OFF vehicle 7. High and low reverse clutch AT-323
12 Gear does not change
from D
3 → D4 or from
M
3 → M4 .
Refer to AT-212, "
A/T
Does Not Shift: D3 →
D4" . ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143
3. ATF pressure switch 3 and input clutch solenoid valve AT-177,
AT-150
4. ATF pressure switch 1 and front brake solenoid valve AT-175,
AT-154
5. Line pressure test AT- 5 4
6. CAN communication lineAT-106
7. Control valve with TCMAT-243
OFF vehicle 8. Input clutch AT-313
No. Items Symptom Condition Diagnostic Item Reference
page

AT-68
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
13 No Up
Shift Gear does not change
from D
4 → D5 or from
M
4 → M5 .
Refer to AT-215, "
A/T
Does Not Shift: D4 →
D5" . ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
3. ATF pressure switch 1 and front brake solenoid valve AT- 1 7 5,
AT- 1 5 4
4. ATF pressure switch 5 and direct clutch solenoid valve AT- 1 7 9,
AT- 1 5 8
5. Turbine revolution sensor AT- 1 4 1
6. Line pressure test AT- 5 4
7. CAN communication lineAT- 1 0 6
8. Control valve with TCMAT- 2 4 3
OFF vehicle 9. Front brake (brake band)
AT- 2 9 010. Input clutchAT- 3 1 3
14
No Down
Shift In “D” or “M” position,
does not downshift to
4th gear. ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3

3. ATF pressure switch 1 and front brake solenoid valve AT- 1 7 5
,
AT- 1 5 4
4. ATF pressure switch 5 and direct clutch solenoid valve AT- 1 7 9,
AT- 1 5 8
5. CAN communication line AT- 1 0 6
6. Line pressure test AT- 5 4
7. Control valve with TCMAT- 2 4 3
OFF vehicle 8. Front brake (brake band)
AT- 2 9 09. Input clutchAT- 3 1 3
15 In “D” or “M” position,
does not downshift to
3rd gear. ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
3. ATF pressure switch 3 and input clutch solenoid valve AT- 1 7 7,
AT- 1 5 0
4. ATF pressure switch 1 and front brake solenoid valve AT- 1 7 5,
AT- 1 5 4
5. CAN communication line AT- 1 0 6
6. Line pressure test AT- 5 4
7. Control valve with TCMAT- 2 4 3
OFF vehicle 8. Input clutch AT- 3 1 3
No. Items Symptom Condition Diagnostic Item Reference
page

TROUBLE DIAGNOSIS AT-69
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX16
No Down
Shift In “D” or “M” position,
does not downshift to
2nd gear. ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143

3. ATF pressure switch 6, high and low reverse clutch sole-
noid valve AT-181
,
AT-162
4. CAN communication line AT-106
5. Line pressure test AT- 5 4
6. Control valve with TCMAT-243
OFF vehicle 7. High and low reverse clutch AT-323
17 In “D” or “M” position,
does not downshift to
1st gear. ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143
3. ATF pressure switch 5 and direct clutch solenoid valve AT-179,
AT-158
4. CAN communication line AT-106
5. Line pressure test AT- 5 4
6. Control valve with TCMAT-243
OFF vehicle 7. Direct clutch AT-326
18 Slips/Will
Not
Engage When “D” or “M” posi-
tion, remains in 1st
gear. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143
3. Direct clutch solenoid valve AT-158
4. Line pressure test AT- 5 4
5. CAN communication lineAT-106
6. Control valve with TCMAT-243
OFF vehicle 7. 3rd one-way clutch
AT- 3 11
8. 1st one-way clutchAT-318
9. Gear systemAT-278
10. Reverse brakeAT-290
11. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 8 , "
Cross-Sectional View (2WD Models)" or AT- 1 9 ,
"Cross-Sectional View (AWD Models)" ) AT-290
12. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18,
"Cross-Sectional View (2WD Models)" or AT-19, "Cross-
Sectional View (AWD Models)" ) AT-290
No. Items Symptom Condition Diagnostic Item
Reference
page

AT-70
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
19
Slips/Will
Not
Engage When “D” or “M” posi-
tion, remains in 2nd
gear. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
3. Low coast brake solenoid valve AT- 1 6 6
4. Line pressure test AT- 5 4
5. CAN communication lineAT- 1 0 6
6. Control valve with TCMAT- 2 4 3
OFF vehicle 7. 3rd one-way clutch
AT- 3 11
8. Gear systemAT- 2 7 8
9. Direct clutchAT- 3 2 6
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18,
"Cross-Sectional View (2WD Models)" or AT- 1 9 , "Cross-
Sectional View (AWD Models)" ) AT- 2 9 0
20When “D” or “M” posi-
tion, remains in 3rd
gear. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
3. Line pressure test AT- 5 4
4. CAN communication lineAT- 1 0 6
5. Control valve with TCMAT- 2 4 3
OFF vehicle 6. 3rd one-way clutch
AT- 3 11
7. Gear systemAT- 2 7 8
8. High and low reverse clutchAT- 3 2 3
9. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-18, "
Cross-Sectional View (2WD Models)" or AT-19,
"Cross-Sectional View (AWD Models)" ) AT- 2 9 0
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18,
"Cross-Sectional View (2WD Models)" or AT- 1 9 , "Cross-
Sectional View (AWD Models)" ) AT- 2 9 0
No. Items Symptom Condition Diagnostic Item
Reference
page