2005 INFINITI FX35 engine

LASER BEAM AIMING ADJUSTMENT ACS-15
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
3. Start the engine, wait for at least 10 seconds, and touch “START
(NISSAN BASED VHCL)”.
4. Touch “ICC”. If “ICC” is not indicated, go to GI-39, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
5. Touch “WORK SUPPORT”.
6. Touch “LASER BEAM ADJUST”.
7. Touch “START”. CAUTION:
If the adjustment screen does not appear on the CONSULT-
II screen in 10 seconds. After touching “LASER BEAM
ADJUST” screen, the following causes may be considered:

Target is not set accurately.

There is not enough space beside the target.

Deformation of vehicle or the surrounding equipment
unit, bracket, or the surrounding equipment is causing
inappropriate installation of sensor and aiming may be
set out of the adjustable range.
SAIA0450E
PKIB4143E
PKIA8867E
SKIA6191E
SKIA1220E

ACS-32
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2005 July 2005 FX
SELF-DIAGNOSTIC RESULTS
For details, refer to ACS-41, "Diagnostic Trouble Code (DTC) Chart" .
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen. Refer to ACS-30, "
CONSULT-II BASIC OPERATION" .
2. Touch any of “ECU INPUT SIGNALS”, “MAIN SIGNALS” and “SELECTION FROM MENU” on selection screen.
3. Touch “START”.
4. Display the data monitor.
5. If necessary, touch “COPY” in turn, and print data.
Monitored Item
× : Applicable
PKIB0112E
Monitored Item
[unit] ECU INPUT
SIGNALS MAIN
SIGNALS SELEC-
TION FROM MENU Description
VHCL SPEED SE
[km/h] or [mph] ××× Indicates vehicle speed calculated from ICC unit through CAN
communication [ABS actuator and electric unit (control unit)
transmits wheel speed sensor signal through CAN communica-
tion].
SET VHCL SPD
[km/h] or [mph] ×× Indicates set vehicle speed memorized in ICC unit.
THRTL OPENING
[%] ××× Indicates throttle angle read from ICC unit through CAN commu-
nication (ECM transmits throttle angle through CAN communi-
cation).
ENGINE RPM
[rpm] ×× Indicates engine speed read from ICC unit through CAN com-
munication (ECM transmits engine speed through CAN commu-
nication).
DISTANCE ADJ
[SHOR/MID/LONG] ×××
Indicates set distance memorized in ICC unit.
WIPER SW
[OFF/LOW/HIGH] ×× Indicates wiper [OFF/LOW/HIGH] status (BCM transmits front
wiper request signal through CAN communication).
MAIN SW
[ON/OFF] ××× Indicates [ON/OFF] status as judged from ICC steering switch
signal (ECM transmits ICC steering switch signal through CAN
communication).
SET/COAST SW
[ON/OFF] ××× Indicates [ON/OFF] status as judged from ICC steering switch
signal (ECM transmits ICC steering switch signal through CAN
communication).
CANCEL SW
[ON/OFF] ××× Indicates [ON/OFF] status as judged from ICC steering switch
signal (ECM transmits ICC steering switch signal through CAN
communication).
RESUME/ACC SW
[ON/OFF] ××× Indicates [ON/OFF] status as judged from ICC steering switch
signal (ECM transmits ICC steering switch signal through CAN
communication).
CRUISE OPE
[ON/OFF] ×× Indicates whether controlling or not (ON means “controlling”).
BRAKE SW
[ON/OFF] ××× Indicates [ON/OFF] status as judged from ICC brake switch sig-
nal.
STOP LAMP SW
[ON/OFF] ×××
Indicates [ON/OFF] status as judged from stop lamp switch sig-
nal.

ACS-34
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2005 July 2005 FX
ACTIVE TEST
CAUTION:

Never perform the active test while driving.

Active test cannot be started while ICC system warning indicator illuminates.
1. Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen. Refer to ACS-30, "
CONSULT-II BASIC OPER-
AT I O N" .
2. Touch any of “ICC BUZZER 1”, “METER LAMP”, “STOP LAMP” and “BOOSTER SOL/V 3” on selection screen.
3. Touch necessary item and “START”.
4. Active test screen will be shown.
ICC BUZZER 1

Touch “ON” and “OFF” to check that ICC warning chime oper-
ates as in the following chart.
METER LAMP

Start the engine.

Touch “ON” and “OFF” to check that ICC system display oper-
ates as in the following chart.
STOP LAMP

Touch “ON” and “OFF” to check that stop lamp operates as in
the following chart.
SKIA6195E
BUZZER O/P ON OFF
Buzzer sound Beep Not activated
SKIA1228E
METER LAMP ON OFF
ICC system display Full illumination OFF
SKIA1231E
STP LMP DRIVE ON OFF
Stop lamp Lamp ON Lamp OFF
SKIA1232E

ACS-36
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2005 July 2005 FX
Self-Diagnostic FunctionAKS00C8N
WITH CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop vehicle, turn ignition switch OFF, then connect CONSULT-II and CONSULT-II CONVERTER to data link connector.
3. With engine started, touch “START (NISSAN BASED VHCL)”, “ICC”, “SELF-DIAG RESULTS” on CON- SULT-II screen in this order.
CAUTION:
If “ICC” cannot be shown after several attempts, the ICC unit may have had malfunction. Repair or
replace it. Refer to GI-39, "
CONSULT-II Data Link Connector (DLC) Circuit" .
4. Self-diagnostic result appears on screen. If “NO DTC ···” is shown, check ICC warning lamp. If any mal- function is indicated, GO TO step 5.
5. According to ACS-41, "
Diagnostic Trouble Code (DTC) Chart" , perform appropriate check, and repair or
replace malfunctioning part as necessary.
6. Turn ignition switch OFF.
7. Start the engine and touch “START (NISSAN BASED VHCL)”, “ICC”, “SELF-DIAG RESULT”, and “ERASE” on CONSULT-II display in turn to erase the memory.
CAUTION:
If the memory does not erase, go to 5.
8. Perform ICC system running test (drive vehicle with ICC system ON), and make sure that ICC warning lamp does not illuminate.
WITHOUT CONSULT-II
1. Go to operation check after asking the customer for symptom information. Refer to ACS-9, "ACTION
TEST" .
2. Stop the vehicle to start the self-diagnosis.
3. Turn ignition switch OFF.
4. From 5 seconds through 15 seconds after turning ignition switch ON, press RESUME/ACCELERATE switch 5 times, and SET/
COAST switch 5 times.
CAUTION:

Never start the engine.

Never turn the MAIN switch ON.

When operation above is not completed from 5 seconds
through 15 seconds, start again from above go to 3.

If self-diagnosis mode cannot be started after several
attempts, the ICC unit may have had malfunction. Repair
or replace it. Refer to ACS-38, "
SELF-DIAGNOSIS BY ICC
SYSTEM DISPLAY WILL NOT RUN" .
PKIA9675E

ACS-70
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2005 July 2005 FX
2. CHECK FUNCTION
After adjusting ICC sensor beam aiming, perform ICC system running test. Check that preceding vehicle
detection performance has been improved.
OK or NG
OK >> INSPECTION END
NG >> 1. Replace ICC sensor, and perform laser beam aiming adjustment.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
Symptom 8: The System Does Not Detect the Vehicle Ahead at AllAKS00C9F
1. VISUAL CHECK 1
With ignition switch turned ON (engine not started), check that all indicator lamps in ICC system display are
continuously lit. (Check for a missing segment in preceding vehicle detection display.)
OK or NG
OK >> GO TO 2.
NG >> Check for combination meter. Refer to DI-15, "
Trouble Diagnosis" .
2. VISUAL CHECK 2
Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Perform ICC system running test.
NG >> GO TO 3.
3. VISUAL CHECK 3
Check ICC sensor body window for cracks and scratches.
OK or NG
OK >> GO TO 4.
NG >> 1. Replace ICC sensor, and perform laser beam aiming adjustment.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.
4. ADJUST ICC SENSOR
After adjusting ICC sensor beam aiming, perform ICC system running test. Check that preceding vehicle
detection performance has been improved.
OK or NG
OK >> INSPECTION END
NG >> 1. Replace ICC sensor, and perform laser beam aiming adjustment.
2. Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system again.

AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D E
F
G H
I
J
K L
M
SECTION AT
A
B
AT
Revision: 2005 July 2005 FX
AUTOMATIC TRANSMISSION
INDEX FOR DTC ........................................................ 5
Alphabetical Index ............................................... ..... 5
DTC No. Index .................................................... ..... 6
PRECAUTIONS ..................................................... ..... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine ............................................... ..... 7
Precautions ......................................................... ..... 8
Service Notice or Precautions ............................. ..... 9
PREPARATION ...................................................... ... 10
Special Service Tools .......................................... ... 10
Commercial Service Tools ................................... .... 11
A/T FLUID .............................................................. ... 12
Changing A/T Fluid ............................................. ... 12
Checking A/T Fluid .............................................. ... 13
A/T Fluid Cooler Cleaning ................................... ... 15
A/T CONTROL SYSTEM ....................................... ... 18
Cross-Sectional View (2WD Models) .................. ... 18
Cross-Sectional View (AWD Models) .................. ... 19
Shift Mechanism .................................................. ... 20
TCM Function ...................................................... ... 31
CAN Communication ........................................... ... 32
Input/Output Signal of TCM ................................. ... 32
Line Pressure Control ......................................... ... 33
Shift Control ........................................................ ... 34
Lock-up Control ................................................... ... 35
Engine Brake Control .......................................... ... 36
Control Valve ....................................................... ... 37
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 39
Introduction ......................................................... ... 39
OBD-II Function for A/T System .......................... ... 39
One or Two Trip Detection Logic of OBD-II ......... ... 39
OBD-II Diagnostic Trouble Code (DTC) .............. ... 39
Malfunction Indicator Lamp (MIL) ........................ ... 42
TROUBLE DIAGNOSIS ......................................... ... 43
DTC Inspection Priority Chart ............................. ... 43
Fail-safe .............................................................. ... 43
How to Perform Trouble Diagnosis for Quick and Accurate Repair ...................................................
... 45
A/T Electrical Parts Location ............................... ... 50
Circuit Diagram .................................................... ... 51
Inspections Before Trouble Diagnosis ................. ... 52
Check Before Engine Is Started .......................... ... 56
Check at Idle ........................................................ ... 57
Cruise Test - Part 1 .............................................. ... 58
Cruise Test - Part 2 .............................................. ... 60
Cruise Test - Part 3 .............................................. ... 61
Vehicle Speed at Which Gear Shifting Occurs .... ... 62
Vehicle Speed at Which Lock-up Occurs/Releases ... 63
Symptom Chart .................................................... ... 64
TCM Input/Output Signal Reference Values ........ ... 89
CONSULT-II Function (A/T) ................................. ... 90
Diagnostic Procedure without CONSULT-II ......... .103
DTC U1000 CAN COMMUNICATION LINE ........... .106
Description ........................................................... .106
On Board Diagnosis Logic ................................... .106
Possible Cause .................................................... .106
DTC Confirmation Procedure .............................. .106
Wiring Diagram — AT — CAN ............................. .107
Diagnostic Procedure .......................................... .108
DTC P0615 START SIGNAL CIRCUIT .................. .109
Description ........................................................... .109
CONSULT-II Reference Value ............................. .109
On Board Diagnosis Logic ................................... .109
Possible Cause .................................................... .109
DTC Confirmation Procedure .............................. .109
Wiring Diagram — AT — STSIG ......................... .110
Diagnostic Procedure .......................................... ..111
DTC P0700 TCM .................................................... .113
Description ........................................................... .113
On Board Diagnosis Logic ................................... .113
Possible Cause .................................................... .113
DTC Confirmation Procedure .............................. .113
Diagnostic Procedure .......................................... .113
DTC P0705 PARK/NEUTRAL POSITION SWITCH .114
Description ........................................................... .114
CONSULT-II Reference Value ............................. .114
On Board Diagnosis Logic ................................... .114

AT-2Revision: 2005 July 2005 FX
Possible Cause ....................................................
.114
DTC Confirmation Procedure .............................. .114
Wiring Diagram — AT — PNP/SW ...................... .115
Diagnostic Procedure .......................................... .116
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) .............................................. .118
Description ........................................................... .118
CONSULT-II Reference Value ............................. .118
On Board Diagnosis Logic ................................... .118
Possible Cause .................................................... .118
DTC Confirmation Procedure .............................. .118
Wiring Diagram — AT — VSSA/T ........................ .120
Diagnostic Procedure .......................................... .121
DTC P0725 ENGINE SPEED SIGNAL .................. .123
Description ........................................................... .123
CONSULT-II Reference Value ............................. .123
On Board Diagnosis Logic ................................... .123
Possible Cause .................................................... .123
DTC Confirmation Procedure .............................. .123
Diagnostic Procedure .......................................... .124
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE ................................................ .125
Description ........................................................... .125
CONSULT-II Reference Value ............................. .125
On Board Diagnosis Logic ................................... .125
Possible Cause .................................................... .125
DTC Confirmation Procedure .............................. .125
Diagnostic Procedure .......................................... .126
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) .127
Description ........................................................... .127
CONSULT-II Reference Value ............................. .127
On Board Diagnosis Logic ................................... .127
Possible Cause .................................................... .127
DTC Confirmation Procedure .............................. .127
Diagnostic Procedure .......................................... .128
DTC P0745 LINE PRESSURE SOLENOID VALVE .129
Description ........................................................... .129
CONSULT-II Reference Value ............................. .129
On Board Diagnosis Logic ................................... .129
Possible Cause .................................................... .129
DTC Confirmation Procedure .............................. .129
Diagnostic Procedure .......................................... .130
DTC P1702 TRANSMISSION CONTROL MODULE
(RAM) ..................................................................... .131
Description ........................................................... .131
On Board Diagnosis Logic ................................... .131
Possible Cause .................................................... .131
DTC Confirmation Procedure .............................. .131
Diagnostic Procedure .......................................... .131
DTC P1703 TRANSMISSION CONTROL MODULE
(ROM) ..................................................................... .132
Description ........................................................... .132
On Board Diagnosis Logic ................................... .132
Possible Cause .................................................... .132
DTC Confirmation Procedure .............................. .132
Diagnostic Procedure .......................................... .132
DTC P1705 THROTTLE POSITION SENSOR ...... .133
Description ........................................................... .133
CONSULT-II Reference Value ............................. .133 On Board Diagnosis Logic ...................................
.133
Possible Cause .................................................... .133
DTC Confirmation Procedure ............................... .133
Diagnostic Procedure ........................................... .134
DTC P1710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT ................................................................. .136
Description ........................................................... .136
CONSULT-II Reference Value .............................. .136
On Board Diagnosis Logic ................................... .136
Possible Cause .................................................... .136
DTC Confirmation Procedure ............................... .136
Wiring Diagram — AT — FTS .............................. .137
Diagnostic Procedure ........................................... .138
Component Inspection ......................................... .140
DTC P1716 TURBINE REVOLUTION SENSOR ... .141
Description ........................................................... .141
CONSULT-II Reference Value .............................. .141
On Board Diagnosis Logic ................................... .141
Possible Cause .................................................... .141
DTC Confirmation Procedure ............................... .141
Diagnostic Procedure ........................................... .142
DTC P1721 VEHICLE SPEED SENSOR MTR ...... .143
Description ........................................................... .143
CONSULT-II Reference Value .............................. .143
On Board Diagnosis Logic ................................... .143
Possible Cause .................................................... .143
DTC Confirmation Procedure ............................... .143
Diagnostic Procedure ........................................... .144
DTC P1730 A/T INTERLOCK ................................ .145
Description ........................................................... .145
On Board Diagnosis Logic ................................... .145
Possible Cause .................................................... .145
DTC Confirmation Procedure ............................... .145
Judgement of A/T Interlock .................................. .145
Diagnostic Procedure ........................................... .146
DTC P1731 A/T 1ST ENGINE BRAKING .............. .148
Description ........................................................... .148
CONSULT-II Reference Value .............................. .148
On Board Diagnosis Logic ................................... .148
Possible Cause .................................................... .148
DTC Confirmation Procedure ............................... .148
Diagnostic Procedure ........................................... .149
DTC P1752 INPUT CLUTCH SOLENOID VALVE . .150
Description ........................................................... .150
CONSULT-II Reference Value .............................. .150
On Board Diagnosis Logic ................................... .150
Possible Cause .................................................... .150
DTC Confirmation Procedure ............................... .150
Diagnostic Procedure ........................................... .151
DTC P1754 INPUT CLUTCH SOLENOID VALVE
FUNCTION ............................................................. .152
Description ........................................................... .152
CONSULT-II Reference Value .............................. .152
On Board Diagnosis Logic ................................... .152
Possible Cause .................................................... .152
DTC Confirmation Procedure ............................... .152
Diagnostic Procedure ........................................... .153
DTC P1757 FRONT BRAKE SOLENOID VALVE .. .154
Description ........................................................... .154

AT-3
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
CONSULT-II Reference Value .............................
. 154
On Board Diagnosis Logic .................................. . 154
Possible Cause ................................................... . 154
DTC Confirmation Procedure .............................. . 154
Diagnostic Procedure .......................................... . 155
DTC P1759 FRONT BRAKE SOLENOID VALVE
FUNCTION ............................................................. . 156
Description .......................................................... . 156
CONSULT-II Reference Value ............................. . 156
On Board Diagnosis Logic .................................. . 156
Possible Cause ................................................... . 156
DTC Confirmation Procedure .............................. . 156
Diagnostic Procedure .......................................... . 157
DTC P1762 DIRECT CLUTCH SOLENOID VALVE . 158
Description .......................................................... . 158
CONSULT-II Reference Value ............................. . 158
On Board Diagnosis Logic .................................. . 158
Possible Cause ................................................... . 158
DTC Confirmation Procedure .............................. . 158
Diagnostic Procedure .......................................... . 159
DTC P1764 DIRECT CLUTCH SOLENOID VALVE
FUNCTION ............................................................. . 160
Description .......................................................... . 160
CONSULT-II Reference Value ............................. . 160
On Board Diagnosis Logic .................................. . 160
Possible Cause ................................................... . 160
DTC Confirmation Procedure .............................. . 160
Diagnostic Procedure .......................................... . 161
DTC P1767 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE ................................................ . 162
Description .......................................................... . 162
CONSULT-II Reference Value ............................. . 162
On Board Diagnosis Logic .................................. . 162
Possible Cause ................................................... . 162
DTC Confirmation Procedure .............................. . 162
Diagnostic Procedure .......................................... . 163
DTC P1769 HIGH AND LOW REVERSE CLUTCH
SOLENOID VALVE FUNCTION ............................ . 164
Description .......................................................... . 164
CONSULT-II Reference Value ............................. . 164
On Board Diagnosis Logic .................................. . 164
Possible Cause ................................................... . 164
DTC Confirmation Procedure .............................. . 164
Diagnostic Procedure .......................................... . 165
DTC P1772 LOW COAST BRAKE SOLENOID
VALVE .................................................................... . 166
Description .......................................................... . 166
CONSULT-II Reference Value ............................. . 166
On Board Diagnosis Logic .................................. . 166
Possible Cause ................................................... . 166
DTC Confirmation Procedure .............................. . 166
Diagnostic Procedure .......................................... . 167
DTC P1774 LOW COAST BRAKE SOLENOID
VALVE FUNCTION ................................................ . 168
Description .......................................................... . 168
CONSULT-II Reference Value ............................. . 168
On Board Diagnosis Logic .................................. . 168
Possible Cause ................................................... . 168 DTC Confirmation Procedure ..............................
.168
Diagnostic Procedure .......................................... .169
DTC P1815 MANUAL MODE SWITCH ................. .170
Description ........................................................... .170
CONSULT-II Reference Value in Data Monitor Mode .170
On Board Diagnosis Logic ................................... .170
Possible Cause .................................................... .170
DTC Confirmation Procedure .............................. .170
Wiring Diagram — AT — MMSW ........................ .171
Diagnostic Procedure .......................................... .173
Component Inspection ......................................... .174
DTC P1841 ATF PRESSURE SWITCH 1 .............. .175
Description ........................................................... .175
CONSULT-II Reference Value ............................. .175
On Board Diagnosis Logic ................................... .175
Possible Cause .................................................... .175
DTC Confirmation Procedure .............................. .175
Diagnostic Procedure .......................................... .176
DTC P1843 ATF PRESSURE SWITCH 3 .............. .177
Description ........................................................... .177
CONSULT-II Reference Value ............................. .177
On Board Diagnosis Logic ................................... .177
Possible Cause .................................................... .177
DTC Confirmation Procedure .............................. .177
Diagnostic Procedure .......................................... .178
DTC P1845 ATF PRESSURE SWITCH 5 .............. .179
Description ........................................................... .179
CONSULT-II Reference Value ............................. .179
On Board Diagnosis Logic ................................... .179
Possible Cause .................................................... .179
DTC Confirmation Procedure .............................. .179
Diagnostic Procedure .......................................... .180
DTC P1846 ATF PRESSURE SWITCH 6 .............. .181
Description ........................................................... .181
CONSULT-II Reference Value ............................. .181
On Board Diagnosis Logic ................................... .181
Possible Cause .................................................... .181
DTC Confirmation Procedure .............................. .181
Diagnostic Procedure .......................................... .182
MAIN POWER SUPPLY AND GROUND CIRCUIT .183
Wiring Diagram — AT — MAIN ........................... .183
Diagnostic Procedure .......................................... .184
CLOSED THROTTLE POSITION AND WIDE OPEN
THROTTLE POSITION CIRCUIT ........................... .187
CONSULT-II Reference Value ............................. .187
Diagnostic Procedure .......................................... .187
BRAKE SIGNAL CIRCUIT ..................................... .188
CONSULT-II Reference Value ............................. .188
Diagnostic Procedure .......................................... .188
A/T INDICATOR CIRCUIT ...................................... .189
Description ........................................................... .189
CONSULT-II Reference Value ............................. .189
Diagnostic Procedure .......................................... .189
TROUBLE DIAGNOSIS FOR SYMPTOMS ........... .190
Wiring Diagram — AT — NONDTC ..................... .190
A/T CHECK Indicator Lamp Does Not Come On . 193
Engine Cannot Be Started in “P” or “N” Position . .194
In “P” Position, Vehicle Moves When Pushed ..... .195