2005 CITROEN C6 engine

Downloaded from www.Manualslib.com manuals search engine 19
GENERAL
LUBRICANTS - TOTAL recommended oils
Gearbox oil
Engine coolant
All countriesCITROËN fluid
Protection: -35C°2Litres
5Litres
20 Litres
210Litres9979 70
9979 71
9979 76
9979 779979 72
9979 73
9979 74
9979 75 PacksCITROËN references
REVKOGEL 2000 GLYSANTIN G33 AM6 automatic gearbox All countriesJWS 3309 (ESSO)
Synthetic brake fluidAll countriesCITROËN fluid
1/2Litre
DOT 4 Packs
CITROËN references Power steering oil
Power-assisted steering All countriesLDS TOTAL H50126
Hydraulic circuit
All countriesColour
1Litre
TOTAL FLUIDE LDS Packs
CITROËN references Norm
Orange
Angl-C6-page001-21-2005 4/02/05 17:12 Page 19

Downloaded from www.Manualslib.com manuals search engine 20
GENERAL
LUBRICANTS - TOTAL recommended oils
Screen wash fluid
Greasing
General use
All countriesConcentrate: 250ml
Fluid
ready to
use9980 33
9980 06
9980 05ZC 9875 953U
ZC 9875 784U
ZC 9885 077U9980 56
ZC 9875 279U PacksCITROËN references
1Litre
5Litres
NLGI norms
2
TOTAL MULTIS 2
TOTAL PETITES MECANISMES All countries
Nota : NLGI= National Lubrificating Grease Institude.
Angl-C6-page001-21-2005 4/02/05 17:12 Page 20

Downloaded from www.Manualslib.com manuals search engine 21
GENERAL
ENGINE OIL CONSUMPTION
I-Oil consumption depends on:
- The engine type.
- How run-in or worn it is.
- The type of oil used.
- The driving conditions.
II -An engine can be considered RUN-INafter:
- 3 000 miles (5 000 km)for a PETROLengine.
- 6 000 miles (10 000 km)for a DIESELengine.
III - MAXIMUM PERMISSIBLEoil consumption for a RUN-INengine.
- 0.5 litresper 600 miles (1 000 km)for a PETROLengine.
- 1 litreper 600 miles (1 000 km)for a DIESELengine.
DO NOT INTERVENE BELOW THESE VALUES.
IV - OIL LEVEL:The level should NEVERbe above the MAX.mark on the dipstick after changing or topping up the oil.
- This excess oil will be used up rapidly.
- It will reduce the engine output and adversely affect the operation of the air circuits and gas recycling.
Angl-C6-page001-21-2005 4/02/05 17:12 Page 21

Downloaded from www.Manualslib.com manuals search engine ENGINE SPECIFICATIONS
Engine type
Cubic capacity (cc)
Bore/stroke
Compression ratio
Power ISO or EEC (KW - rpm)
Torque ISO or EEC (m.daN - rpm)Engines: ES9A - DT17TED4
Petrol Diesel
3.0i 24S 2,7 24V
XFV UHZ
2946 2720
87/82,6 81x88
10,9/1 17,3/1
155-6000 150-4000
29-3750 44-1900
22
ENGINE
Angl-C6-page022-82-2005 4/02/05 17:19 Page 22

Downloaded from www.Manualslib.com manuals search engine 23
ENGINE
TIGHTENING TORQUES: POWER UNIT SUSPENSION
Torque reaction rod - lower RH engine support
16 ± 0,521 ± 0,136,5 ± 0,5
LH engine support
43 ± 0,356,5 ± 0,665 ± 0,575,5 ± 0,5
Upper RH engine support
8-96 ± 0,6104,5 ± 0,5116 ± 0,5126 ± 0,5
Engine: ES9A
B1BP32YP
Angl-C6-page022-82-2005 4/02/05 17:19 Page 23

Downloaded from www.Manualslib.com manuals search engine 24
ENGINE
ENGINE TIGHTENING TORQUES
1 Pencil-type ignition coil 0,8 ± 0,3
Sparking plugs
Pre-tightening1 ± 0,1
Angular tightening90° ± 5°
Valve cover
2Pre-tightening0,5 ± 0,1Tightening1 ± 0,1
Camshaft bearing cap cover
3Pre-tightening0,2 ± 0,1Tightening1 ± 0,1
Cylinder head
Pre-tightening2 ± 0,2
4Slackeningyes
Tightening1,5 ± 0,1Angular tightening225° ± 5° Engine: ES9A
B1BP27DP
Angl-C6-page022-82-2005 4/02/05 17:19 Page 24

Downloaded from www.Manualslib.com manuals search engine 25
ENGINE
ENGINE TIGHTENING TORQUES
Exhaust manifold (equipped with a new gasket)
5Pre-tightening(order from 1 to 10)1 ± 0,1Tightening(order from 1 to 10)3 ± 0,3
Con rod caps
6Pre-tightening2 ± 0,2Angular tightening74° ± 5°
Engine flywheel
7Pre-tightening2 ± 0,2Angular tightening60° ± 5° Engine: ES9A
B1JP02LD
Angl-C6-page022-82-2005 4/02/05 17:19 Page 25

Downloaded from www.Manualslib.com manuals search engine 26
ENGINE
ENGINE TIGHTENING TORQUES
8 Crankshaft bearing
NOTE: Maximum length under heads for M11 = 131,5 mm.
NOTE: Maximum length under heads for M8 = 119 mm.
Perform the following operations:
- Brush the screw threads.
- Refit the screws having first pre-coated them with «MOLYKOTE G RAPID PLUS»grease on the threads and under heads.
Check the presence of the eight centring pins
Pre-tighten the screws M11(sequence from 1to 8)3 ± 0,3
Pre-tighten the screws M8(sequence from Ato H)1 ± 0,1
Tighten the screws M6 (sequence from ato 1)1 ± 0,1Slacken the screws screws M11and M8 Yes
Proceeding screw by screw
Tighten the screws M11(sequence from 1to 8)3 ± 0,3
Angular tightening180°
Tighten the screws M8(sequence from Ato H)1 ± 0,1Angular tightening180° Engine: ES9A
B1BP2D3D
Angl-C6-page022-82-2005 4/02/05 17:19 Page 26