2005 Citroen BERLINGO Camshaft

Downloaded from www.Manualslib.com manuals search engine 187
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: KFW - NFV
Pre-tensioning the timing belt (continued).
Make sure of the timing setting by refitting the pegs [1]and [2].
Remove the valve cover.
Position the tool [5]
(respect the direction of fitting relative to the valve timing).
Adjusting the belt tension.
Place tool [4]on the tensioned part of the belt.
Slacken the nut (2).
Detension the belt, but too much.
Tension the timing belt to obtain a value of: 31 ± 2 SEEMunits.
Tighten the nut (2)to 2 m.daN.
Remove tools [1], [2], [4] and [5].
Checking the belt tension.
Rotate the crankshaft 2 turnsin the normal direction of rotation.
Check that it is still possible to peg the following components.
Flywheel.
Camshaft.
IMPERATIVE: Repeat the belt tensioning operation if the pegging is not possible.
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 187

Downloaded from www.Manualslib.com manuals search engine 188
ENGINECHECKING THE VALVE TIMING
Engine: KFU
Tools.
[1] Flywheel setting peg: 4507-TA. Toolkit 4507-T
[2] Camshaft setting peg: 4533-TA.C1
[3] Camshaft setting peg: (-).0194.A
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Deconnect the battery.
Remove:
- The engine cover.
- The upper timing cover (1).
- The oil filter (2).
Remove the sparking plugs to facilitate rotation of the engine.
Turn the engine by means of the crankshaft screw.
IMPERATIVE: Never turn the engine backwards.
Suspend the engine.
Remove:
- The screws (3), the upper RH engine support (4)and the screws (5).
B1BP37JC
B1BP37KC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 188

Downloaded from www.Manualslib.com manuals search engine 190
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Tools.
[1]Flywheel setting peg: 4507-T.A
[2]Camshaft setting peg: 4533-T.AC1
[3] Camshaft setting peg: (-).0194.A
[4] Belt retaining pin: 4533-TA.D
IMPERATIVE: Respect the safety and cleanliness requirements.
Setting the timing.
Raise and support the vehicle, wheels hanging.
Disconnect the battery.
Remove the engine cover.
Raise and support the vehicle, wheels hanging.
Remove:
- The accessories drive belt (3)
(see corresponding operation).
- The crankshaft pulley, the engine cover.
- The upper timing cover (1).
- The oil filter (2).
Remove the sparking plugs to facilitate rotation of the engine.
Suspend the engine.
Remove the screws (4), the upper RH engine support (5)and the screws (6).
B1BP37QD
B1BP37RC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 190

Downloaded from www.Manualslib.com manuals search engine 191
ENGINE
191
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Setting the timing (continued).
Rotate the engine by means of the crankshaft screw
(clockwise), to bring it to the pegging position.
Peg the flywheel, using tool [1].
Position the tools [2]and [3].
Remove the engine support assembly (9), the fixing
screw (8)and the lower cover (7).
Slacken the nut (11).
Fully detension the belt by moving the tensioner
roller (10).
Remove the timing belt.
IMPERATIVE: Check that the tensioner roller
turns freely
(no tight spot).
Refitting.
Position the
(new)timing belt, in the following
sequence:
- The inlet camshaft pulley, the exhaust camshaft
pulley, the guide roller, the crankshaft pulley, position
the tool [4], the coolant pump pulley, the dynamic
tensioner roller.
Remove the tools [1], [2], [3]and [4].
B1BP2MBC
B1BP2ZMC
B1CP0GLD
B1CP0GMD
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 191

Downloaded from www.Manualslib.com manuals search engine 193
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Tools.
[1]Belt tension measuring instrument: 4122-T
[2]Flywheel locating peg: 4507-T.A
[3]Camshaft pulley locating peg, exhaust: 4533-T.A C2 Tool kit 4507-T
[4]Camshaft pulley locating peg, inlet: 4533-T.A C1
[5]Tensioning tool: 4707-T.J
Checking the valve timing.
Peg the flywheel using the tool [2].
Peg the exhaust camshaft pulley [3].
Peg the inlet camshaft pulley [4].
Setting the valve timing.
Peg the flywheel using the tool [2].
Peg the camshaft pulleys[3]and [4].
B1EP11CC
B1EP11BC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 193

Downloaded from www.Manualslib.com manuals search engine 195
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Turn the two pulleys (1)clockwise to the end of the slots.
With the belt strip (e)fully tensioned, place the belt over the pulley, first exhaust side, then inlet side, while
ensuring that marks (b)and (c)on the belt are aligned with marks (f)on the pulleys.
Hold the belt in this position and engage it over the water pump pinion and the tensioner roller.
Fit the tool [1] on the belt at (e).
Rotate the roller (2)
(using tool [5])in an anti-clockwise direction, to obtain: 63 SEEMunits.
Tighten the roller (2)to 2 m.daN.
Tighten the six screws (5)to 1 m.daN.
Essential: Check that:
- The camshaft pulleys (1)are not at the end of the slots
(by removing a screw).
- The markings on the belt are aligned with the markings on the crankshaft and camshaft pulleys.
If not, repeat the setting procedure.
B1EP11GC
B1EP11FC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 195

Downloaded from www.Manualslib.com manuals search engine 196
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Remove the tools [1], [2], [3]and [4].
Rotate the engine by four turnsin the normal direction
(do not turn backwards).
Peg the flywheel [2].
Loosen the six screws (5), while ensuring there is still a slight amount of friction with the pulley.
Peg the camshaft hubs using pegs [3]and [4].
WARNING: In certain cases, it may be necessary to slightly turn the camshaft using the hub fixing screw.
Fit the tool [1].
Loosen the tensioner roller screw (2).
Rotate the roller (2)
(using tool [5])in an anti-clockwise direction to obtain: 37 SEEMunits.
Tighten the tensioner roller screw (2)to 2 m.daN.
Tighten the six pulley screws (1)to 1 m.daN.
Remove the tools.
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 196

Downloaded from www.Manualslib.com manuals search engine 197
ENGINE
CHECKING THE VALVE TIMING
Engine: NFU
Tools.
[1]Flywheel setting peg: 4507-T.A Toolkit 4507-T
[2a]Camshaft setting peg: 4533-TA.C1
[3b]Camshaft setting peg: 4533-TA.C2
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Disconnect the negative terminal of the battery.
Remove:
- The oil filter (1).
- Suspend the engine.
Remove:
- The engine support (2)and the upper timing cover (3).
B1BP2M7C
B1BP381C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 197