2005 Citroen BERLINGO DRIVE BELT wjy

Downloaded from www.Manualslib.com manuals search engine 131
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Crankshaft
Bearing cap fixing screws7 ± 0,7
Con rod nuts
Pre-tightening2 ± 0,2
Angular tightening70°±5°
Accessories drive pulley hub
Pre-tightening4 ± 0,2
Angular tightening55°±5°
Accessories drive pulley1 ± 0,1
Cylinder block
Piston skirt spray jet1 ± 0,1
Sump1,6 ± 0,1
Timing belt guide roller4,3 ± 0,4
Timing belt tensioner roller2,1 ± 0,2
Cylinder head
Camshaft bearing covers2 ± 0,2
Exhaust manifold0,3
Valve cover0,5
Camshaft / hub4,3 ± 0,4
Camshaft pinion / hub2,3 ± 0,2 Engine: WJY
XSARA
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 131

Downloaded from www.Manualslib.com manuals search engine 132
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Crankshaft
Bearing cap fixing screws7 ± 0,7
Con rod nuts
Pre-tightening2 ± 0,2
Angular tightening70°±5°
Accessories drive pulley hub
Pre-tightening4 ± 0,2
Angular tightening55°±5°
Accessories drive pulley1 ± 0,1
Cylinder block
Piston spray jet1 ± 0,1
Sump1,6 ± 0,1
Timing belt guide roller4,3 ± 0,4
Timing belt tensioner roller2,1 ± 0,2
Cylinder head
Camshaft bearing covers2 ± 0,2
Exhaust manifold3 ± 0,3
Valve cover0,5
Camshaft / hub4,3 ± 0,4
Camshaft pinion / hub2,3 ± 0,2 Engine: WJY
XSARA
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 132

Downloaded from www.Manualslib.com manuals search engine 153
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
DV
TD
410
B BTED4
Engine type
C4
XSARA
XSARA PICASSO
See pages:
8HX 8HZ 9HY 9HZ 9HY 9HZ 9HX WJY RHY RHZ RHR
XX X X
XX XXX
XX X
165 to 166 167 to 168 169 167 to 168 170 to 175 176 to 179 180DW
6
TD 8ATED4TED4ATED
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 153

Downloaded from www.Manualslib.com manuals search engine 170
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Without power-assisted steering
Tool.
[1]Belt tension measuring instrument: 4122-T
Removal.
Loosen the screws (2).
Tighten the screw (1)until it is against its stop.
Remove the belt.
Refitting.
Refit the belt.
Fit the tool [1] on the belt at "d".
Tighten the screw (1)to obtain: 106 ± 10 SEEMunits.
Tighten the screws (2)to 2 m.daN.
Remove the tool [1].
B1BP1SECB1BP1SDC
Engine: WJY
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 170

Downloaded from www.Manualslib.com manuals search engine 171
ENGINE
XSARAAUXILIARY EQUIPMENT DRIVE BELT
Without power-assisted steering, with air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
Loosen the screws (1).
Tighten the screw (2)until it is against its stop.
Remove the belt.
Refitting.
Refit the belt.
Fit the tool [1] at "e".
Tighten the screw (2)to obtain: 106 ± 10 SEEMunits.
Tighten the screws (1)to 2 m.daN.
Remove the tool [1].
B1BP1SGCB1BP1SFC
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 171

Downloaded from www.Manualslib.com manuals search engine 172
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, without air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
WARNING: If the belt is to be reused, measure the tension before removal.
Loosen:
- the screw (1).
- the nut (2).
NOTE:The tensioner arm (3)must be against the alternator.
Remove the belt.
B1BP1SHD
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 172

Downloaded from www.Manualslib.com manuals search engine 173
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: WJY
Power-assisted steering, without air conditioning (continued)
XSARA
Refitting.
Refit the belt.
Place the tool [1]on belt at "f".
WARNING: Position tool [1] with the knob downwards.
Tighten the nut (2)to obtain a value of:
Reused belt:
- Keep the value taken at removal.
New belt:
- Tension should be 110 SEEMunits.
- Tighten the screw (1)to 9.5 m.daN.
- Check belt tension, using tool [1].
Tension should be 144 ± 3 SEEMunits.
- Remove the tool [1].
- Start the engine and run it for 10 seconds.
- Stop the engine.
- Place the tool [1]on the belt at "f".
- Tension should be 130 ± 4 SEEMunits.
- Remove the tool [1].
B1BP1SJD
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 173

Downloaded from www.Manualslib.com manuals search engine 174
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, with air conditioning
Tools.
[1] Dynamic tensioner peg: (-) 0188 H
[2] Belt tension measuring instrument: 4122-T
Removal.
Peg the dynamic tensioner (1) at "a", using tool [1].
Loosen the screw (2)of the roller (3).
Turn the roller (3)backwards.
Remove the belt.
NOTE:If it can not be pegged at "a":
- Loosen the screw (2)of the roller (3).
- Using a 7 mmsquare drive, turn the roller (3)at "b".
- Peg the tensioner (1) at "a", using tool [1].
NOTE: If the belt is broken:
- Support the engine using a jack
(insert a wooden block between the housing and the jack).
- Remove the right engine support.
- Using a square drive at (b)turn the tool (3)in the direction of the arrow "a", so that it can be
pegged at "a"using the tool [1].
B1BP1SKC
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 174