2004 MITSUBISHI L200 low oil pressure

INSTRUMENTS AND CONTROLS
Indication and warning lampsED50APDc
1 - Automatic transmission indication lamp
(vehicle with automatic transmission) →p. 5-16
2 - Turn-signal indication lamps / Hazard warning indication
lamps
3 - High-beam indication lamp
4 - Low fuel indication lamp
5 - Check engine indication lamp (diesel-powered vehicles)*
6 - Supplemental restraint system (SRS) warning lamp*
→p. 3-29
7 - Door ajar warning lamp
8 - Anti-lock brake (ABS) warning lamp
(diesel-powered vehicles)* →p. 5-34
9 - Overdrive off indication lamp
(vehicle with automatic transmission) →p. 5-18
10 - Rear fog lamp indication lamp*11 - A/T (automatic transmission) temperature warning lamp*
12 - 4WD indication lamp (4-wheel drive vehicles) →p. 5-22
13 - Charge warning lamp
14 - Oil pressure warning lamp
15 - Fuel filter indication lamp (diesel-powered vehicles)
16 - Brake warning lamp
17 - Diesel preheat warning lamp (diesel- powered vehicles)
18 - Check engine indication lamp (petrol-powered vehicles)
19 - Anti-lock brake (ABS) warning lamp
(petrol-powered vehicles)* →p. 5-34
NOTE
To find information concerning the indication or warning lamps
marked by the symbol “ →p. x-xx”, refer to the specified pages.
For the other indication and warning lamps, refer to the subse-
quent pages.
4-6
D50A467
12 32
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
04engL2_240082_4 22-01-2004 13:19 Page 4-6

INSTRUMENTS AND CONTROLS
Oil pressure warning lamp - redED25A-Ai
This lamp illuminates when the ignition key is
turned “ON”, and goes off after the engine has
started. If it illuminates while the engine is run-
ning, the oil pressure is too low.
If the warning lamp illuminates while the engine is
running, turn the engine off. And contact your near-
est authorized MITSUBISHI dealer for inspection.
CAUTION(1) If this lamp illuminates when the engine
oil level is not low, contact your nearest
authorized MITSUBISHI dealer for in-
spection.
(2) This warning lamp does not indicate
the amount of oil in the crankcase. This
must be determined by checking the oil
level on the dipstick, while the engine
is switched off.
(3) If you continue driving with low engine
oil level or with this warning lamp illu-
minated, engine seizure may occur.
NOTE
The oil pressure warning lamp should not be
treated as an indication of the engine’s oil level.
The oil level must be checked using the dipstick.
Fuel filter indication lamp - amber
(diesel-powered vehicles only)
ED59A-Bc
This lamp illuminates when the ignition switch is
turned to the “ON” position and goes off after the
engine has started. If it lamps up while the engine
is running, it indicates that water has accumul-
ated inside the fuel filter; if this happens, remove
the water from the fuel filter.
When the lamp goes out, you can resume driving.
If it either does not go out or comes on from time to
time, have the vehicle inspected at an authorized
MITSUBISHI dealer.
Brake warning lamp - redED23A-Ie
With the ignition switch “ON”, the brake warning
lamp illuminates under the following conditions:
(1)
When the parking brake lever has been engaged.(2) When the brake fluid level in the reservoir
falls to a low level.
(3) If a malfunction develops in the brake servo
system. (Diesel-powered vehicles only)
(4)
If the brake warning lamp and charge warning
lamp come on at the same time while the en-
gine is running, it is possible that the alternator
belt is broken. (Diesel-powered vehicles only)
4-9
04engL2_240082_4 22-01-2004 13:19 Page 4-9

STARTING AND DRIVING
5-26
Correct 4-wheel drive
operation
EI32ABDa
By shifting lock to 4-wheel drive (4H, 4L),
both axles of the vehicle are rigidly con-
nected with each other. This improves the
traction characteristics. When turning
sharp corners or moving forward and
backward repeatedly, however, the drive
line is stressed, which is felt as a braking
effect. A 4-wheel drive vehicle can accele-
rate more quickly and smoothly.
However, note that the braking distance is
not shorter than that of a rear-wheel drive
vehicle.
When using 4-wheel drive on rough roads
(snow, mud, sand, etc.), it is important to
operate the vehicle correctly.
NOTE
(1) The driving posture should be more
upright and closer to the wheel than
usual; adjust the seat to a good posi-
tion for easy steering and pedal oper-
ation. Be sure to wear the seat belt.
(2) After driving on rough roads, check
each part of the vehicle and wash it
thoroughly with water. Refer to the
“Vehicle care” section and “Inspection
and maintenance following rough
road operation” sections.Driving on dry paved road and highway
Select 2WD (2H) to drive on dry paved
roads. Especially on dry highway, never
select the 4WD (4H or 4L).
CAUTIONSelecting 4-wheel drive to drive on
dry paved road will increase the fuel
consumption with possible noise
generation and early tyre wear.
It may also increase the differential
oil temperature, resulting in possible
damage to the driving system. Fur-
ther, the drive train will be subjected
to excessive loading, possibly lead-
ing to oil leakage, component
seizure, or other serious faults.
Driving on snowy or icy roads
Set the transfer shift lever to “4H” or “4L” in
accordance with the road conditions, and
then gradually depress the accelerator
pedal for a smooth start.
NOTE
(1) The use of snow tyres and/or tyre
chains is recommended.
(2) Maintain a safe distance between
vehicles, avoid sudden braking, and
use engine braking (downshifting).
CAUTIONAvoid sudden braking, sudden ac-
celeration, and sharp turning; such
operations could cause skidding
and spinouts.
Driving on sandy or muddy roads
Set the transfer shift lever to “4H” or “4L”,
and then gradually depress the accelera-
tor pedal for a smooth start. Keep the
pressure on the accelerator pedal as con-
stant as possible, and drive at low speed.
05engL2_240082_4 22-01-2004 13:05 Page 5-26

STARTING AND DRIVING
5-29
CAUTIONNever cross a stream where the
water is deep.
Do not change gears while crossing
the stream.
Frequent crossing of streams can
adversely affect the life span of the
vehicle; consult an authorized
MITSUBISHI dealer and take the ne-
cessary measures to prepare, in-
spect, and repair the vehicle.
After crossing a stream, apply the brakes
to be sure they are functioning properly. If
the brakes are wet and not functioning
properly, dry them out by driving slowly
while lightly depressing the brake pedal.
Inspect each part of the vehicle carefully.
Refer to the “Inspection and maintenance
following rough road operation” section.
Cautions on handling of
4WD vehicles
EI49A-Ce
Tyres and wheels
Since the driving torque can be applied to
the 4 wheels, the performance of the vehi-
cle when operating in 4WD is greatly
affected by the condition of the tyres.
Pay close attention to the tyres.
• Install specified tyres on all wheels. Re-
fer to the “Tyres and wheels” on page
10-8, 10-14, 10-22.
• All tyres should be rotated whenever the
wear difference between front and rear
tyres is recognizable.
Good vehicle performance cannot be
expected if there is a difference in wear
between tyres. Refer to the “Tyre rota-
tion” on page 9-11.
• Check the tyre inflation pressure regu-
larly.
Inspection and maintenance
following rough road operation
After operating the vehicle in rough road
conditions, be sure to perform the following
inspection and maintenance procedures:
(1) Check that the vehicle has not been
damaged by rocks, gravel, etc.
(2) Carefully wash the vehicle with water.
Drive the vehicle slowly while lightly
depressing the brake pedal in order to
dry out the brakes. If the brakes still
do not function properly, contact an
authorized MITSUBISHI dealer as
soon as possible to have the brakes
checked.
(3) Remove the insects, dried grass, etc.
clogging the radiator core.
(4) If a stream has been crossed, check
the engine, transmission, and differ-
ential oil and propeller shaft grease. If
the oil or grease is milky or cloudy
because of water contamination, it
must be replaced with new oil.
(5) Check the inside of the vehicle. If
ingress of water is found, dry the car-
pet etc.
(6) Inspect the headlamps. If the head-
lamp bulb is flooded with water, have
the headlamp drained off at an autho-
rized MITSUBISHI dealer.
(7) Have an authorized MITSUBISHI
dealer replace grease in the wheel
bearing.
05engL2_240082_4 22-01-2004 13:05 Page 5-29

Engine coolantEM36A-Gg
A translucent coolant reserve tank is lo-
cated in the engine compartment. The
coolant level in this tank should be kept
between the “LOW” and “FULL” marks
when measured while the engine is cold.
The cooling system is a closed system
and normally the loss of coolant should be
very slight. A noticeable drop in the
coolant level could indicate leakage. If this
occurs, have the system checked at an
authorized MITSUBISHI dealer as soon
as possible. If the level should drop below
the “LOW” level on the reserve tank, open
the lid and add coolant.
Also, if the reserve tank is completely
empty, remove the radiator cap and add
coolant until the level reaches the filler
neck.
MAINTENANCE
CAUTION(1) Do not use alcohol or methanol
anti-freeze or any engine
coolants mixed with alcohol or
methanol anti-freeze. The use of
an improper anti-freeze can
cause the corrosion of the alu-
minium components.
(2) For effective anti-corrosion and
anti-freeze performance, keep
the anti-freeze concentration
within the range of 30 to 60%.
Concentrations exceeding 60%
will result in a reduction of both
the anti-freeze and cooling per-
formance thus adversely affect-
ing the engine.
(3) Do not top up with water only.
Water by itself reduces the rust-
protective and anti-freeze qual-
ities of the coolant and has a
lower boiling point. It can also
cause damage to the cooling
system if it should freeze. Do not
use tapwater, or it causes the
corrosion and rust formation.
CAUTIONDo not open the radiator cap while
the engine is hot. The coolant sys-
tem is under pressure and any hot
coolant escaping could cause se-
vere burns.
Anti-freeze
The engine coolant contains an ethylene
glycol anti-corrosion agent. The cylinder
head and water pump housing are cast
aluminium alloy, and periodic changing of
the engine coolant is necessary to prevent
corrosion of these parts.
Use MITSUBISHI Genuine Coolant or an
equivalent.
MITSUBISHI Genuine Coolant has excel-
lent protection against corrosion and rust
formation of all metals including alu-
minium and can avoid clogs in the radia-
tor, heater, cylinder head, engine block,
etc.
Because of the necessity of this anti-
corrosion agent, the coolant must not be
replaced with plain water even in summer.
The required concentration of anti-freeze
differs depending on the expected
ambient temperature.
9-5
M36A003
Ambient
temperature
(minimum) °C-15-20-25-30-35-50
Anti-freeze
concentration %303540455060
09engL2_240082_4 22-01-2004 13:12 Page 9-5

INDEX
Gauges ........................................................ 4-3
Genuine parts ............................................ 1-15
Glove box .................................................. 6-35
Hazard warning flasher switch .................. 4-18
Hazard warning indication lamp .................. 4-7
Headlamp
Headlamp levelling switch ...................... 4-14
Headlamps
Headlamps, Dipper, Passing .................. 4-12
Replacement ........................................... 8-35
Washer switch......................................... 4-17
Head restraints ............................................ 3-5
Heated seats ............................................... 3-7
Heater/Air conditioning .............................. 6-19
High-beam indication lamp .......................... 4-7
Hinges and latches lubrication................... 9-16
Horn switch ................................................ 4-20
Ignition switch .............................................. 5-9
Inclinometer ................................................. 4-4
Indication and warning lamps ...................... 4-6
Inside rear-view mirror ............................... 5-37
Installation of accessories ......................... 1-13
Instruments .................................................. 4-2
Jack ............................................................. 8-5
Jack handle ................................................. 8-7
Jacking up the vehicle ................................. 8-8
Jump starting (Emergency starting) .......... 8-27
Keyless entry system................................... 2-5
Keys............................................................. 2-2Leakage (Fuel, engine coolant,
oil and exhaust gas) ................................ 9-14
Light
Bulb capacity........................................... 8-34
Headlamps .............................................. 4-12
Room lamps ............................................ 4-20
Limited-slip differential ............................... 5-35
Low fuel indication lamp .............................. 4-7
Manual transmission
Driving speed .......................................... 5-14
Shifting .................................................... 5-14
Manual window control ................................ 2-9
Meter, gauge and indication/warning
lamp operation ........................................ 9-14
Meter illumination control........................... 4-20
Mirrors
Day/Night Type inside rear-view mirror .. 5-37
Electric remote-controlled
outside rear-view mirrors ...................... 5-38
Vanity mirror............................................ 6-32
Octane rating ............................................... 5-3
Odometer/Tripmeter .................................... 4-3
Oil pressure warning lamp ........................... 4-9
Oil
Engine oil ....................................... 9-2, 10-26
Manual transmission oil ........................ 10-26
Operation under adverse
driving conditions ...................................... 8-2
Overheating (Engine) ................................ 8-23Parking ............................................. 5-20, 5-32
Parking brake ............................................ 5-30
Performance ....................... 10-5, 10-11, 10-18
Pillar antenna............................................. 6-18
Polishing ...................................................... 7-6
Power steering
Fluid ............................................... 9-9, 10-26
System .................................................... 5-37
Pregnant women restraint ......................... 3-20
Punctured .................................................. 8-16
Quarter window ......................................... 2-11
Rear differential lock .................................. 5-23
Rear fog lamp switch ................................. 4-19
Rear gate ................................................... 2-12
Rear heater................................................ 6-30
Rear seat ..................................................... 3-5
Rear secret box ......................................... 6-37
Rear window demister switch .................... 4-18
Rear-view mirrors ...................................... 5-37
Removal of water from the fuel filter
(diesel-powered vehicles only) ............... 8-26
Replacement of lamp bulbs ....................... 8-34
Front turn-signal and position lamps ....... 8-36
Headlamps .............................................. 8-35
High-mounted stop lamps ....................... 8-38
Side turn-signal lamps ............................ 8-36
Number-plate lamps ............................... 8-37
Rear combination lamps ......................... 8-37
Rear fog lamps........................................ 8-38
Rheostat .................................................... 4-20
Roof drip moulding .................................... 1-14
Room lamps .............................................. 4-20
10-28
10engL2_240082_4 22-01-2004 13:14 Page 10-28