2004 MITSUBISHI ENDEAVOR Speaker

YES: Install the speaker securely. The speaker should now be free of
distortion.
NO: Repair or replace the radio and CD player. The speaker should now
be free of distortion.
INSPECTION PROCEDURE 20: Distortion on FM Only. DIAGNOSIS
STEP 1. Check that the distortion is present when the radio is tuned to
another station.
Q: Does the distortion persist when the radio is tuned to another station?
YES: Go to Step 2.
NO: The signal from that station is too weak.
STEP 2. Relocate the reception area and check the radio.
Q: When relocating the reception area does the distortion increase or
decrease?
YES: The cause may be multipath or fading noise. Multipath noise is the
echo that occurs when the broadcast signal is reflected by a large
obstruction and enters the receiver with a slight time delay relative to the
direct signal (repetitious buzzing). A fading or buzzing noise may occur
when the broadcast beam is disrupted by obstructing objects and the signal
strength fluctuates within a narrow range.
NO: Replace the radio and CD player. Check that a distortion is resolved.
INSPECTION PROCEDURE 21: Auto Select Function Inoperative, too Few Automatic Stations are Selected. DIAGNOSIS
STEP 1. Check the state of the antenna.
Q: Is the mast antenna assembled?
YES: Go to Step 2.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Check the power of ignition switch "ACC"
.
Q: Does the radio and CD player power turn ON when the ignition switch is in
the "ACC" or "ON" position?
YES: Either replace the audio. Check that a CD can be ejected normally.
NO: Check the memory backup power supply circuit. Refer to INSPECTION
PROCEDURE 1
.
ON-VEHICLE SERVICE SPEAKER TEST < VEHICLES WITH SEVEN SPEAKERS > Operate the radio panel switches to test the speakers. The middle grade type multi-
center display shows which speaker is sounding. Enter the speaker test mode
according to the following steps:
1. Turn the ignition switch to "ACC" position and switch off the audio
2. Press the following buttons in that order within 60 seconds from step (1).
1. Memory select "1" button
2. "SEEK" switch (down side)
3. "SEEK" switch (up side)
4. Memor
y select "6" button

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 151: Displaying Memory Button

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Check that the speaker, which is displayed on the multi-center display (middle
grade type), sounds (If the memory select "6" button is pressed, the speaker
will be changed).
4. If a button other than the memory select "6" button and "EJECT" button (CD)
is pressed, or the ignition switch is turned to "LOCK" (OFF) position, you will
exit from the speaker test mode.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 152: Displaying Front Speaker (LH)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SPECIAL TOOL
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 157: Measuring Resistance Value Between Terminal

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 158: Identifying Switch Position

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SPEAKER REMOVAL AND INSTALLATION Instrument Panel
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 159: Removing/Installing Speaker

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Door Speakers
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 160: Removing/Installing Speaker

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Quarter Trim Pane
l
Fig. 161: Removing/Installing Speaker

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
AMPLIFIER REMOVAL AND INSTALLATION
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor