2004 MITSUBISHI ENDEAVOR heater

Fig. 31: Identifying Connector C
- 104

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is joint connector (2) C-104 in good condition?
YES: Go to Step 13 .
NO: Repair or replace the damaged component(s). And then check to see
that the heater function of the door mirror (RH) operates normally.
STEP 13. Check the wiring harness between remote controlled mirror
(RH) connector E-01 (terminal 1) and joint connector (2) C-104 (terminal
24).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door Mirror - Endeavor

Fig. 34: Identifying Connector C
- 13

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the wiring harness between the remote controlled mirror (RH)
connector E-01 (terminal 1) and joint connector (2) C-104 (terminal 24) in
good condition?
YES: No action is necessary and testing is complete.
NO: Repair the wiring harness as necessary. And then check to see that
the heater function of the door mirror (RH) operates normally.
DOOR MIRROR REMOVAL AND INSTALLATION
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door Mirror - Endeavor

Fig. 38: Identifying Remote Controlled Mirror Switch Terminal

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
DOOR MIRROR HEATER CHECK Check to see that the resistance shown in the graph is almost satisfied when
measuring the resistance of terminals 1 and 2 of the remote controlled mirror
connectors under 2 or more different temperature conditions.Right side
OFF
9-2, 9-3, 9-6, 1-2, 1-3, 1-6
Open circuit
Up
1-6, 3-9
Less than 2 ohms
Down
1-3, 6-9
Right
1-6, 2-9
Left
1-2, 6-9
CAUTION: When relocating the car between locations with
extremely different temperatures (warm and cold),
leave the car in the location for a while to adapt to
the temperature prior to checking it.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door Mirror - Endeavor

Fig. 4: Checking Continuity Between Terminals

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Check that the indicator is lighted at HI or LO when battery voltage is supplied
to terminal 5 and terminal 8 is grounded.
3. Check that indicator is lighted when battery voltage is supplied to terminals 2
and terminal 6.
SEAT CUSHION HEATER CHECK Measure the resistance between terminals.
Standard value: At room tem
perature 20 °C (68 °F)

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Front & Rear Seat Assembly - Endeavor

Between terminals 2 and terminal 3: Approximately 4.0 ohms +/- 9%
Between terminals 1 and terminal 3: 4.1 ohms +/- 9%
Fig. 5: Measuring Resistance Between Terminals (Seat Cushion Heater)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SEATBACK HEATER CHECK Measure the resistance between terminals.
Standard value: At room temperature 20 °C (68 °F) Approximately 3.6
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Front & Rear Seat Assembly - Endeavor

ohms +/- 9%
Fig. 6: Measuring Resistance Between Terminals (Seatback Heater)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
HEATED SEAT RELAY CONTINUITY CHECK
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Front & Rear Seat Assembly - Endeavor