2004 MITSUBISHI ENDEAVOR ECU

DTC 21: DRIVE
R-SIDE AIR BAG MODULE SHORT CIRCUIT
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. If DTC 34 is
retrieved, go to next step. If DTC 34 is not retrieved, go to step 3 .
2. Inspect SRS ECU connector C-26. See SRS ELECTRONIC CONTROL
UNIT (SRS ECU)
under REMOVAL & INSTALLATION. See Fig. 19
. If
SRS ECU connector C-26 is connected correctly, go to next step. If SRS ECU
connector is not connected properly, install connector correctly. Go to step 8 .
3. Disconnect negative battery cable. Disconnect, then reconnect SRS ECU
connector C-26, lower clockspring connector C-307 and driver-side air bag
module connector C-305. See DRIVER
-SIDE AIR BAG MODULE &
CLOCKSPRING
under REMOVAL & INSTALLATION. Connect negative
battery cable. Using scan tool, erase then retrieve DTCs. If DTC 21 is
retrieved, go to next step. If DTC 21 is not retrieved, system is normal at this
time.
4. Disconnect negative battery cable. Connect Resistor Harness (MB991866) to
terminals of upper clockspring connector C-306 by backprobing connector.
Connect Load Resistor (MB991865) to resistor harness. Connect negative
battery cable. Using scan tool, erase then retrieve DTCs. If DTC 21 is
retrieved, go to next step. If DTC 21 is not retrieved, replace driver-side air bag
module. Go to step 8 .
5. Disconnect negative battery cable. Connect resistor harness and load resistor to
terminals No. 3 and 4 of clockspring connector C-307 by backprobing
connector. See Fig. 24
. Connect negative battery cable. Using scan tool, erase
then retrieve DTCs. If DTC 21 is retrieved, go to next step. If DTC 21 is not
retrieved, replace clockspring. Go to step 8 .
6. Disconnect SRS ECU connector C-26 and clockspring connector C-307. Insert
a cable tie or similar insulator between terminals No. 11 (Yellow/Black wire)
and No. 12 (Yellow wire) of SRS ECU connector to release shorting bar. See
Fig. 21
. Check for continuity between terminals No. 11 and 12. If continuity
exists, go to next step. If continuity does not exist, erase, then retrieve DTCs
using scan tool. If DTC 21 is retrieved, replace SRS ECU. Go to step 8 .
7. Check wire harness between SRS ECU connector C-26 and lower clockspring
connector C-307 for a short circuit. If wire harness is okay, go to next step. If
wire harness has a short circuit, replace wire harness. Go to next step

2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

go to next step. If DTC 22 is not retrieved, replace driver-side air bag module.
Go to step 4 .
2. Disconnect negative battery cable. Disconnect clockspring connector C-307.
Connect resistor harness to clockspring connector C-307 by backprobing
connector terminals No. 3 and 4. See Fig. 24
. Connect negative battery cable.
Using scan tool, erase then retrieve DTCs. If DTC 22 is retrieved, go to next
step. If DTC 22 is not retrieved, replace clockspring. Go to step 4 .
3. Disconnect SRS ECU connector C-26 and clockspring connector C-307. See
SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL &
INSTALLATION. Measure resistance between connector C-26, terminal No.
11 (Yellow/Black wire) and clockspring connector C-307, terminal No. 3.
Measure resistance between connector C-26, terminal No. 12 (Yellow wire)
and clockspring connector C-307, terminal No. 4. If resistance is less than 2
ohms in each circuit, recheck for DTCs. If DTC 22 is retrieved, replace SRS
ECU. Go to next step. If resistance is more than 2 ohms in either wire, replace
wire harness between SRS ECU and clockspring. Go to next step.
4. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 22 is retrieved, go to step 1 . If DTC 22 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 24: PASSENGER-SIDE AIR BAG MODULE SHORT CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM
. If
DTC 34 is retrieved, go to next step. If DTC 34 is not retrieved, go to step 3 .
2. Inspect SRS ECU connector C-26. See SRS ELECTRONIC CONTROL
UNIT (SRS ECU)
under REMOVAL & INSTALLATION. See Fig. 19
. If
connector is not connected properly, connect properly. Go to step 7 . If
connector is connected properly, go to next step.
3. Disconnect negative battery cable. Disconnect, then reconnect passenger-side
air bag module connector C-09 and SRS ECU connector C-26. See
PASSENGER
-SIDE AIR BAG MODULE
under REMOVAL &
INSTALLATION. Connect negative battery cable. Using scan tool, erase then
retrieve DTCs. If DTC 24 is retrieved, go to next step. If DTC 24 is not
retrieved, s
ystem is normal at this time.

2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

4. Disconnect negative battery cable. Disconnect passenger-side air bag connector
C-09. Connect Resistor Harness (MB991866) to connector C-09 by
backprobing connector. Connect Load Resistor (MB991865) to resistor
harness. Connect negative battery cable. Using scan tool, erase then retrieve
DTCs. If DTC 24, is retrieved, go to next step. If DTC 24 is not retrieved,
replace passenger-side air bag module. Go to step 7 .
5. Disconnect SRS ECU connector C-26. Disconnect passenger-side air bag
module connector C-09. Insert a cable tie or similar insulator between
terminals No. 9 (Yellow/Green wire) and No. 10 (Yellow/Red wire) of SRS
ECU connector C-26 to release shorting bar. See Fig. 21
. Check for continuity
between terminals. If continuity exists, go to next step. If continuity does not
exist, erase, then retrieve DTCs using scan tool. If DTC 24 is retrieved, replace
SRS ECU. Go to step 7 .
6. Check wire harness between SRS ECU and passenger-side air bag module for
damage. If wire harness is okay, go to next step. Replace wire harness, if
damaged. Go to next step.
7. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 24 is retrieved, go to step 1 . If DTC 24 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 25: PASSENGER-SIDE AIR BAG MODULE OPEN CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM
. Go
to next step.
2. Disconnect passenger-side air bag module connector C-09. See PASSENGER
-
SIDE AIR BAG MODULE
under REMOVAL & INSTALLATION. See Fig.
19 . Connect Resistor Harness (MB991866) to connector C-09 by backprobing
connector. Connect Load Resistor (MB991865) to resistor harness. Connect
negative battery cable. Using scan tool, erase then retrieve DTCs. If DTC 25 is
retrieved, go to next step. If DTC 25 is not retrieved, replace passenger-side air
bag module. Go to step 4 .
3. Measure resistance of Yellow/Red and Yellow/Green wires between SRS ECU
connector C-26, terminals No. 9 and 10 and passenger-side air bag module
connector
C-09, terminals No. 1 and 2. See Fig. 21
. If resistance is less than 2

2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

ohms in each wire, go to next step. If resistance is more than 2 ohms in either
wire, replace wire harness. Go to next step.
4. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 25 is retrieved, go to step 1 . If DTC 25 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 26: DRIVER-SIDE SEAT BELT PRETENSIONER SHORT CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable SRS.
See DISABLING & ACTIVATING AIR BAG SYSTEM
. If DTC 34 is
retrieved, go to next step. If DTC 34 is not retrieved, go to step 3 .
2. Inspect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL
UNIT (SRS ECU)
under REMOVAL & INSTALLATION. See Fig. 19
. If
connector is connected properly, go to next step. If connector is not connected
properly, connect properly and go to step 7 .
3. Disconnect negative battery cable. Disconnect, then reconnect SRS ECU
connector C-25 and driver-side seat belt pretensioner connector D-24. See
SEAT BELT PRETENSIONER
under REMOVAL & INSTALLATION.
Connect negative battery cable. Using scan tool, check for DTCs. If DTC 26 is
retrieved, go to next step. If DTC 26 is not retrieved, system is normal at this
time.
4. Disconnect negative battery cable. Connect Load Resistor (MB991865) to
Resistor Harness (MB991884). Connect resistor harness to driver-side seat belt
pretensioner connector D-24. Connect negative battery cable. Using scan tool,
check for DTCs. If DTC 26 is retrieved, go to next step. If DTC 26 is not
retrieved, replace driver-side seat belt pretensioner.
5. Disconnect SRS ECU connector C-25 and driver-side seat belt connector D-24.
Insert a cable tie or similar insulator between terminals No. 29 (Red/Blue wire)
and No. 30 (Red/Yellow wire) of SRS ECU connector to release shorting bar.
See Fig. 21
. If continuity exists between terminals No. 29 and 30, go to next
ste
p. If continuit
y does not exist, between terminals No. 29 and 30, erase, then
NOTE: Ensure shorting bar in SRS ECU connector is released by
using a cable tie or similar non conducting item to release
shorting bar before performing electrical measurements.
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

retrieve DTCs using scan tool. If DTC 26 is retrieved, replace SRS ECU. Go to
step 7 .
6. Measure continuity of Red and Red/White wires between SRS ECU connector
C-25, terminals No. 29 and 30 and driver-side seat belt pretensioner connector
D-26, terminals No. 1 and 2. See Fig. 25
. If continuity does not exist in both
wires, replace wire harness between driver-side seat belt pretensioner and SRS
ECU. Go to next step. If continuity exists in both wires, go to next step.
7. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 26 is retrieved, go to step 1 . If DTC 26 is not
retrieved, system is normal at this time. Intermittent condition may exist.
Fig. 25: Identifying Seat Belt Pretensioner Connector D
-24 & D
-32 Terminals

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
DTC 27: DRIVER-SIDE SEAT BELT PRETENSIONER OPEN CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable SRS.
See DISABLING & ACTIVATING AIR BAG SYSTEM
. Go to next ste
p.
NOTE: Ensure shorting bar in SRS ECU connector is released by
using a cable tie or similar non conducting item to release
shorting bar before performing electrical measurements.
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

2. Disconnect driver-side seat belt pretensioner connector D-24. See SEAT
BELT PRETENSIONER
under REMOVAL & INSTALLATION. See Fig.
19 . Connect Load Resistor (MB991865) to Resistor Harness (MB991884).
Connect resistor harness to driver-side seat belt pretensioner connector.
Connect negative battery cable. Using scan tool, check for DTCs. If DTC 27 is
retrieved, go to next step. If DTC 27 is not retrieved, replace driver-side seat
belt pretensioner.
3. Disconnect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION. Measure
resistance of Red/Blue wire between SRS ECU connector C-25, terminal No.
29 and driver-side seat belt pretensioner connector D-26, terminal No. 1. See
Fig. 21
& Fig. 25
. Measure resistance of Red/Yellow wire between SRS ECU
connector terminal No. 30 and driver-side seat belt pretensioner connector D-
26, terminal No. 2. If resistance is 2 ohms or less in both wires, erase, then
retrieve DTCs using scan tool. If DTC 27 is retrieved, replace SRS ECU. Go to
next step. If resistance is more than 2 ohms in either wire, replace wire harness
between SRS ECU and seat belt pretensioner. Go to next step.
4. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 27 is retrieved, go to step 1 . If DTC 27 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 28: PASSENGER-SIDE SEAT BELT PRETENSIONER SHORT CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable SRS.
See DISABLING & ACTIVATING AIR BAG SYSTEM
. If DTC 34 is
retrieved, go to next step. If DTC 34 is not retrieved, go to step 3 .
2. Inspect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL
UNIT (SRS ECU)
under REMOVAL & INSTALLATION. See Fig. 19
. If
connector is connected properly, go to next step. If connector is not connected
properly, connect properly. Go to step 7 .
3. Disconnect ne
gative batter
y cable. Disconnect SRS ECU connector
C-25 and
NOTE: Ensure shorting bar in SRS ECU connector is released by
using a cable tie or similar non conducting item to release
shorting bar before performing electrical measurements.
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

passenger-side seat belt pretensioner connector D-32. See SEAT BELT PRETENSIONER
under REMOVAL & INSTALLATION. Reconnect
connectors. Connect negative battery cable. Using scan tool, check for DTCs.
If DTC 28 is retrieved, go to next step. If DTC 28 is not retrieved, system is
normal at this time.
4. Disconnect negative battery cable. Connect Load Resistor (MB991865) to
Resistor Harness (MB991884). Connect resistor harness to driver-side seat belt
pretensioner connector D-32. Connect negative battery cable. Using scan tool,
check for DTCs. If DTC 28 is retrieved, go to next step. If DTC 28 is not
retrieved, replace passenger-side seat belt pretensioner.
5. Disconnect SRS ECU connector C-25 and passenger-side seat belt connector
D-32. Insert a cable tie or similar insulator between terminals No. 27 (Red
wire) and 28 (Red/White wire) of SRS ECU connector to release shorting bar.
See Fig. 21
. Check for continuity between terminals. If continuity exists, go to
next step. If continuity does not exist, erase, then retrieve DTCs using scan
tool. If DTC 28 is retrieved, replace SRS ECU. Go to step 7 .
6. Measure continuity of Red and Red/White wires between SRS ECU connector
C-25, terminals No. 27 and 28 and passenger-side seat belt pretensioner
connector D-39, terminals No. 1 and 2. See Fig. 25
. If continuity does not
exist in both wires, replace wire harness between SRS ECU and passenger-side
seat belt pretensioner. Go to next step. If continuity exists in both wires, go to
next step.
7. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 28 is retrieved, go to step 1 . If DTC 28 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 29: PASSENGER-SIDE SEAT BELT PRETENSIONER OPEN CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Disable SRS.
See DISABLING & ACTIVATING AIR BAG SYSTEM
. Go to next step.
2. Disconnect
passen
ger-side seat belt
pretensioner connector D-32. See SEAT
NOTE: Ensure shorting bar in SRS ECU connector is released by
using a cable tie or similar non conducting item to release
shorting bar before performing electrical measurements,
2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems

BELT PRETENSIONE
R under REMOVAL & INSTALLATION. See Fig.
19 . Connect Load Resistor (MB991865) to Resistor Harness (MB991884).
Connect resistor harness to passenger-side seat belt pretensioner connector.
Connect negative battery cable. Using scan tool, check for DTCs. If DTC 29 is
retrieved, go to next step. If DTC 29 is not retrieved, replace passenger-side
seat belt pretensioner. Go to step 4 .
3. Disconnect SRS ECU connector C-25. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION. Measure
resistance of Red wire between SRS ECU connector C-25, terminal No. 27 and
driver-side seat belt pretensioner connector D-32, terminal No. 1. See Fig. 25
.
Measure resistance of Red/White wire between SRS ECU connector terminal
No. 28 and driver-side seat belt pretensioner connector D-32, terminal No. 2. If
resistance is 2 ohms or less in both wires, erase, then retrieve DTCs using scan
tool. If DTC 29 is retrieved, replace SRS ECU. If resistance is more than 2
ohms in either wire, replace wire harness between SRS ECU and seat belt
pretensioner.
4. Reconnect all SRS components. Activate air bag system. Using scan tool, erase
then retrieve DTCs. If DTC 29 is retrieved, go to step 1 . If DTC 29 is not
retrieved, system is normal at this time. Intermittent condition may exist.
DTC 31 & 32: SRS ECU CAPACITOR If DTC 31 or 32 is present, replace SRS ECU. See SRS ELECTRONIC CONTROL UNIT (SRS ECU)
under REMOVAL & INSTALLATION.
DTC 34: SRS ECU CONNECTOR LOCK CIRCUIT 1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS
. Check SRS-
ECU connectors C-25 and C-26. See SRS ELECTRONIC CONTROL UNIT
(SRS ECU)
under REMOVAL & INSTALLATION. See Fig. 19
. If
connectors are connected properly, go to next step. If connectors are not
connected properly, connect properly. Go to step 3 .
2. Disconnect and inspect connectors C-25 and C-26. If connectors are damaged,
replace wire harness. Go to next step. If connectors are not damaged, reconnect
connectors. Using scan tool, erase then retrieve DTCs. If DTC 34 is retrieved,
re
place SRS ECU. Go to next ste
p.

2004 Mitsubishi Endeavor Limited
2004 ACCESSORIES/SAFETY EQUIPMENT Mitsubishi - Air Bag Restraint Systems