2004 MITSUBISHI ENDEAVOR 2 ohm

2. Turn the ignition switch to the "ON" position.
3. Use scan tool MB991958 to check the actuator test.
Item 09: Engine TCL Drive.
When the accelerator pedal is depressed at the same time that the
button for actuator test item 09 displayed on scan tool MB991958 is
pressed, the system prevents the engine speed from rising for three
seconds.
4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Disconnect scan tool MB991958.
6. If defective, repair it. (Refer to TCL DIAGNOSIS
- SYMPTOM
PROCEDURE
, TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
).
TCL SWITCH CHECK 1. Remove the TCL switch. (Refer to TCL SWITCH
).
2. Measure the resistance between terminal 1 and terminal 2 when the TCL
switch is pressed or released. If the values measured at the time correspond to
those in the table below, the resistance values are correct.
TESTER CONNECTION
WHEEL SPEED SENSOR CHECK Refer to ON
-VEHICLE SERVICE
. CAUTION: The engine speed increases after the actuator
test because the actuator test continues for only
three seconds. Therefore, release the accelerator
pedal immediately.
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Pressed
1-2
Less than 2 ohms
Released
1-2
Open circuit

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control System (TCL) - Endeavor

2. Check to see that the water is vigorously sprayed when connecting the positive
battery terminal to terminal number 2 and terminal number 1 to the ground. REAR WIPER AND WASHER SWITCH CHECK Check continuity between the switch terminals.
REAR WIPER AND WASHER SWITCH CHECK
Fig. 12: Identifying Rear Wiper And Washer Switch TerminalsSWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
OFF
25-26,25-29
Open circuit
Rear wiper switch
25-26
Less than 2 ohms
Rear washer switch
25-29

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Rear Wiper And Washer - Endeavor

Fig. 12: Checking Low Speed Operation

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
WINDSHIELD WIPER SWITCH CHECK WINDSHIELD WIPER SWITCH CHECK SWITCH POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
OFF
21 - 23, 23 - 30, 23 - 31,
23 - 32
Open circuit
Windshield wiper mist
switch ON
23 - 32
Less than 2 ohms
Windshield intermittent
wiper switch ON
23 - 31
Windshield low-speed wiper
switch ON
23 - 30
Windshield hi
gh-s
peed wi
per

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Windshield Wiper And Washer - Endeavor

Fig. 13: Identifying Windsheild Wiper Switch Terminals

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Measure the resistance value at terminal numbers 27 and 28. The resistance value
should rise smoothly from approximately 0 ohm ("FAST" position) to
approximately 1 kohm ("SLOW" position).
WINDSHIELD WASHER REMOVAL AND INSTALLATION switch ON
21 - 23

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Windshield Wiper And Washer - Endeavor

WINDSHIELD WASHER SWITCH CHECKWINDSHIELD WASHER SWITCH CHECK
Fig. 16: Identifying Windshield Washer Switch Terminals

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
SWITCH POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
OFF
22 - 23
Open circuit
Windshield washer switch
ON
22 - 23
Less than 2 ohms

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Windshield Wiper And Washer - Endeavor