2004 MITSUBISHI ENDEAVOR wiring

Fig. 132: Identifying Connector D
-08
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are harness connectors D-08 and C-11 in good condition?
YES: Go to Step 22.
NO: Repair or replace the damaged component(s). The woofer should
sound.
STEP 22. Check the wiring harness between woofer connector D-08
(terminals 1 and 2) and audio amplifier connector C-11 (terminals 8 and
18)

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 135: Identifying Connector C
-112

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the wiring harness between woofer connector D-08 (terminals 1 and
2) and audio amplifier connector C-11 (terminals 8 and 18) in good
condition?
YES: Replace the audio amplifier. The woofer should sound.
NO: Repair the wiring harness. The woofer should sound.
INSPECTION PROCEDURE 8: Noise is Present while Moving (AM). DIAGNOSIS
STEP 1. Ask the driver about the noise.
1. Find out the following information from the owner.
2. Place where the noise occurs.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 145: Identifying Connectors

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
CIRCUIT OPERATION Power is continuously supplied to the radio and CD player. TECHNICAL DESCRIPTION (COMMENT) The cause is probably a faulty radio and CD player memory backup power supply
system circuit. TROUBLESHOOTING HINTS
Damaged wiring harness or connector Malfunction of the radio and CD player
DIAGNOSIS Required Special Tool:
MB991223: Harness set
STEP 1. Measure at radio and CD player or radio, CD player and CD
changer connector C-105 in order to check the power supply circuit to the
radio and CD player (through the battery).
1. Disconnect radio and CD player or radio, CD player and CD changer
connector
C-105, and measure at the wirin
g harness side.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 148: Identifying Connector C
-105

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is radio and CD player or radio, CD player and CD changer connector
C-105 in good condition?
YES: Go to Step 3.
NO: Repair or replace the damaged component(s). Check that a memory
is retained.
STEP 3. Check the wiring harness between radio and CD player or radio,
CD
player and CD chan
ger connector C-105 (terminal 21) and the batter
y.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Q: Is the wiring harness between radio and CD player or radio, CD player
and CD changer connector C-105 (terminal 21) and the battery in good
condition?
YES: Repair or replace the radio and CD player or radio, CD player and
CD changer. Check that a memory is retained.
NO: Repair the wiring harness. Check that a memory is retained.
INSPECTION PROCEDURE 23: CD can not be Inserted. DIAGNOSIS
STEP 1. Check that a CD has been already loaded.
Q: Has a CD been already loaded?
YES: Take out the CD (If the CD can not be ejected, refer to
INSPECTION PROCEDURE 27
). Check that a CD can be inserted.
NO: Go to Step 2.
STEP 2. Check how a CD is inserted.
Ensure that the ignition switch is at 'ACC' or 'ON'.
Q: If you try to load the CD, does the CD stops halfway and then rejected?
YES: Refer to INSPECTION PROCEDURE 27
.
NO: Go to Step 3.
STEP 3. Check after the CD is loaded.
NOTE: If you try to load a CD when the ignition switch is at the
positions other than 'ACC' or 'ON,' the CD will not be
inserted completely and then rejected.
NOTE: Even though the CD is loaded, 'E01' (vehicles with
center display low type) or 'ERROR 01' (vehicles with
center display middle type) sometimes displayed with
the CD rejected because of vibration/shock or dew on

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 162: Removing/Installing Amplifier

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
REMOVAL SERVICE POINTS << A >> AMPLIFIER REMOVAL Move the audio amplifier wiring harness to one side, and then maneuver out the
audio amplifier.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Radio With Tape Player & Cd Player - Endeavor

Fig. 4: Identifying Connector

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
CIRCUIT OPERATION Power is supplied from the battery directly to the M-bus adapter. TECHNICAL DESCRIPTION (COMMENT) The cause is probably a faulty M-bus adapter power supply circuit system. TROUBLESHOOTING HINTS
Damaged wiring harness or connector Damaged DIN cable Malfunction of the M-bus adapter Malfunction of the rear display unit (overhead type)

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Video Entertainment System - Endeavor

NO: Replace the DIN cable.
STEP 8. Measure the resistance value at rear display connector D-36.
1. Disconnect the connector, and measure at the wiring harness side.
Fig. 8: Identifying D
-36 Connector Terminals

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Resistance between rear display connector D-36 terminal No.2 and body
ground
OK: 2 ohm or less

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Video Entertainment System - Endeavor