2004 ISUZU TF SERIES lock

DIAGNOSIS (JR405E) 7A2-3
PAGE
No. B12: NOISE OR VIBRATION IS GENERATED AT STARTING..................................7A2-107
No. C1: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFTED UP TO 1st TO 2
nd........7A2-108
No. C2: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFTED UP TO 2nd TO 3
rd.......7A2-108
No. C3: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFTED UP TO 3rd TO 4
th........7A2-108
No. C4: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN ................................7A2-108
OR KICK-DOWN TO 4th TO 3
rd.................................................................................7A2-108
No. C5: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN OR KICK-DOWN
TO 4th TO 2
nd..............................................................................................................................7A2-108
No. C6: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN OR KICK-DOWN
TO 3rd TO 2
nd.............................................................................................................................7A2-108
No. C7: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN TO 4th OR 3
rd
TO 1
st............................................................................................................................................7A2-108
No. C8: ENGINE RACE UP (SLIP) OTHERS.........................................................................7A2-108
No. C9: BARKING FEEL WHEN GEAR IS SHIFTED UP TO 1st TO 2
nd.........................7A2-111
No. C10: BARKING FEEL WHEN GEAR IS SHIFTED UP TO 2nd TO 3
rd......................7A2-111
No. C11: BARKING FEEL WHEN GEAR IS SHIFTED UP TO 3rd TO 4
th.......................7A2-111
No. C12: LARGE SHOCK WHEN GEAR IS SHIFTED TO 1st TO 2
ND OR 2nd TO 1st..7A2-114
No. C13: LARGE SHOCK WHEN GEAR IS SHIFTED TO 2nd TO 3
rd OR 3rd TO 2nd.7A2-114
No. C14: LARGE SHOCK WHEN GEAR IS SHIFTED TO 3rd TO 4th TO 3
rd................7A2-114
No. C15: LARGE SHOCK WHEN KICK-DOWN....................................................................7A2-114
No. C16: LARGE SHOCK WHEN NO ACCELERATION.....................................................7A2-114
No. C17: LARGE SHOCK WHEN GEAR IS SHIFTED DOWN TO 2nd TO
1st IN L RANGE..........................................................................................................................7A2-114
No. C18: LARGE SHOCK (OTHER)........................................................................................7A2-114
No. C19: LARGE SHOCK WHEN VEHICLE SPEED IS DOWNED BY NO
ACCELERATOR PANEL OR VEHICLE IS STOPPED........................................................7A2-114
No. C20: LARGE LOCK-UP SHOCK.......................................................................................7A2-114
No. C21: SHIFT DOWN OR ENGINE OVER-RUN WHEN THE ACCELERATION
PANE IS STEPPED ON IN 4th GEAR....................................................................................7A2-114
NO. D1: FAULTY GEAR SHIFTING (DIFFERENT FROM SHIFT PATTERN)............... 7A2-115
NO. D2: GEAR IS SHIFTED FREQUENTLY ................................................................. 7A2-120

7A2-4 DIAGNOSIS (JR405E)
PAGE
NO. D3: GEAR SHIFT POINT IS LOW OR HIGH AT ALL POINT................................. 7A2-120
NO. D4: GEAR SHIFT POINT IS LOW OR HIGH AT LIMITED POINT ......................... 7A2-120
NO. D5: NO KICK-DOWN .............................................................................................. 7A2-120
NO. E1: NO GEAR SHIFT .............................................................................................. 7A2-121
NO. E2: ONLY 4TH GEAR (O/D) IS NOT SELECTABLE ............................................. 7A2-124
NO. E3: GEAR IS SHIFTED 2ND TO 3RD IN 2 RANGE ............................................... 7A2-126
NO. E4: GEAR IS SHIFTED 1ST TO 2ND IN L RANGE................................................ 7A2-126
NO. E5: GEAR IS SHIFTED 3RD TO 4TH IN 3 RANGE................................................ 7A2-126
NO. F1: LOW MAXIMUM SPEED OR POOR ACCELERATION ................................... 7A2-127
NO. F2: ENGINE RACES UP DURING ACCELERATION (SLIP) ................................. 7A2-130
NO. F3: NOISE OR VIBRATION DURING THE RUNNING IN R, D, 3, 2 OR L
RANGE .......................................................................................................................... 7A2-130
NO. F4: ENGINE BRAKE DOES NOT APPLY IN L RANGE......................................... 7A2-130
NO. F5: ENGINE STALLS BEFORE VEHICLE STOPS FROM RUNNING ................... 7A2-131
NO. G1: VEHICLE MOVES IN P RANGE OR PARKING GEAR IS NOT
DISENGAGED OTHER THAN P RANGE ..................................................................... 7A2-131
NO. G2: CREEP FORCE IS LARGE.............................................................................. 7A2-131
NO. G3: CREEP FORCE IS SMALL .............................................................................. 7A2-132
NO. G4: LARGE NOISE DURING IDLING WITH THE VEHICLE IN STOP STATE ...... 7A2-133
NO. H1: JUDDER OCCURS AT THE LOCK-UP ........................................................... 7A2-133
NO. H2: LARGE LOCK-UP SHOCK .............................................................................. 7A2-133
NO. H3: LOCK-UP POINT IS HIGH OR LOW ............................................................... 7A2-133
NO. I1: NO LOCK-UP .................................................................................................... 7A2-134
NO. J1: OIL LEAKS FROM BREATHER ....................................................................... 7A2-136
NO. J2: OIL LEAKS BETWEEN ENGINE AND CONVERTER HOUSING .................... 7A2-136
NO. J3: OIL LEAKS BETWEEN MAIN CASE AND CONVERTER HOUSING.............. 7A2-136
NO. J4: OIL LEAKS BETWEEN MAIN CASE AND REAR HOUSING .......................... 7A2-136
NO. J5: OIL LEAKS FROM OIL PAN ............................................................................ 7A2-136
NO. J6: OIL LEAKS FROM MANUAL SHAFT OIL SEAL ............................................. 7A2-136
NO. J7: OIL LEAKS FROM OIL COOLER PIPE JOINT................................................ 7A2-136
NO. Z1: TRANSMISSION OVERHEAT .......................................................................... 7A2-136
NO. Z2: MODE LAMP (POWER DRIVE OR 3RD START) DOES NOT LIGHT UP
WHEN THE POWER MODE OR 3RD START MODE IS TURNED ON........................ 7A2-137

7A2-12 DIAGNOSIS (JR405E)
F0: Diagnostic Trouble Code
F0: Read DTC Infor As Stored By ECU
F1: Clear DTC Information
F1: Data Display
F2: Snapshot
F3: Miscellaneous Test
F0: Lamp
F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmission Check Light Test
F1: Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid
F4: Programming
F0: Program VIN
F1: Lock ECU

F0: Diagnostic Trouble Code
The purpose of the "Diagnostic Trouble Codes" mode is to
display stored trouble code in the TCM.
When "Clear DTC Information" is selected, a "Clear DTC
Information", warning screen appears. This screen informs you
that by cleaning DTC's "all stored DTC information in the TCM
will be erased".
After clearing codes, confirm system operation by test driving
the vehicle.

F1: Data Display
The purpose of the "Data Display" mode is to continuously
monitor data parameters.
The current actual values of all important sensors and signals
in the system are display through F1mode.
See the "Typical Scan Data" section.

F2: Snapshot
"Snapshot" allows you to focus on making the condition occur,
rather than trying to view all of the data in anticipation of the
fault. The snapshot will collect parameter information around a
trigger point that you select.

F3: Miscellaneous Test:
The purpose of "Miscellaneous Test" mode is to check for
correct operation of electronic system actuators.

F4: Programming (Factory Use Only):
The purpose of "Programming" is to program VIN in the ECM
and lock the programmed data.

7A2-14 DIAGNOSIS (JR405E)
MISCELLANEOUS TEST
The state of each circuit can be tested by using miscellaneous test menus. Especially when DTC cannot be
detected, a faulty circuit can be diagnosed by testing each circuit by means of these menus.
Even DTC has been detected, the circuit tests using these menus could help discriminate between a mechanical
trouble and an electrical trouble.

Connect Tech 2 and select "Powertrain", "JR 405E" & "Miscellaneous Test".
F0: Lamps
The circuit is normal if the warning light in the meter panel comes on and goes out in accordance with Tech 2
instruction.

Lamps

F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Tempeature Lamp Test
F3: Transmission Check Light Test


F0: Power Lamp Test


Power Lamp Test

Power Lamp Off



 Press "Active" key.
Then, "POWER DRIVE" indicator lamp is turned on in the meter panel.
 Press "Inactive" key.
Then, "POWER DRIVE" indicator lamp is turned off in the
meter panel.
 Press "Quit" Key to cancel the test.
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmisstion Check Light Test
Test procedure is same as "F0: Power Lamp Test".
The circuit is normal if the warning light in the meter panel
comes on and goes out in accordance with Tech 2 instruction.

F1: Solenoids
The circuit is normal if clicking sound is generated in accordance with Tech 2 instruction.

Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid

DIAGNOSIS (JR405E) 7A2-15
F0: Low & Reverse Brake Solenoid

Low & Reverse Brake Solenoid

Low & Reverse Brake Duty 0%



 Press "Active" key.
Then, duty datio is indicated 100 % and "clicking sound" is
generated from the transmission control valve.
 Press "Inactive" key.
Then, duty datio is indicated 0 % and "clicking sound" is
generated from the transmission control valve.
 Press "Quit" Key to cancel the test.

F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Brake Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid

Test procedure is same as "F0: Low & Revese Brake
Solenoid"
The circuit is normal if clicking sound is generated in
accordance with Tech 2 instruction.

7A2-34 DIAGNOSIS (JR405E)


Flash Code
(P-Code)

CHECK TRANS Flash Pattern

Description
CHECK
TRANS
Warning

34 (P0768) Low Clutch Duty Solenoid FailureON


35 (P0748) Line Pressure Solenoid Failure ON


36 (P1860) Lock-up Duty Solenoid Failure ON


41 (P0731) 1stGearRatioError ON


42 (P0732) 2ndGearRatioError ON


43 (P0733) 3rdGearRatioError ON


44 (P0734) 4thGearRatioError ON


51 (P1750) ON

Low & Reverse Brake Fail-safe
Valve Failure

52 (P1755) 2-4BrakeFail-safeValveFailure ON


- (P0602) No Flash Code ECU Programming Error ON

DIAGNOSIS (JR405E) 7A2-35
FAIL-SAFEFUNCTION
Fail-Safe Condition
Flash Code
(P-Code)

Description
CHECK
TRANS
Warning

Gear Shift
Solenoid
Line
Pressure
Solenoid

Lock-up

Remark
11
(P0722)
Vehicle peed Sensor No
Signal ON 3rdFix All Stop - Inhibited
13
(P0727)
Engine Revolution Sensor
No Signal ON - - - Inhibited
14
(P0717)
Turbine Speed Sensor No
Signal ON 3rdFix All Stop - Inhibited
15
(P0710)
ATF Temperature Sensor
Failure OFF 3,2,L - - Inhibited*1
16
(P0560)
System Voltage Failure ON 3rdFix All Stop - Inhibited*2
17
(P0705)
Inhibitor Switch Failure ON 3rdFix All Stop - Inhibited
22
(P1120)
Throttle Signal Failure ON 3rdFix All Stop - Inhibited
25
(P1875)
GND Return Circuit
Failure ON 3rdFix All Stop - Inhibited*2
26
(P1853)
Low & Reverse Brake
Pressure Switch Failure ON No Fail-safe Function
27
(P1858)
2-4 Brake Pressure
Switch Failure ON No Fail-safe Function
28
(P1863)
High Clutch Pressure
Switch Failure ON No Fail-safe Function
31
(P0753)
Low & Reverse Brake
Duty Solenoid Failure ON 3rdFix All Stop - Inhibited
32
(P0758)
2-4 Brake Duty Solenoid
Failure ON 3rdFix All Stop - Inhibited
33
(P0763)
High Clutch Duty Solenoid
Failure ON 3rdFix All Stop - Inhibited
34
(P0768)
Low Clutch Duty Solenoid
Failure ON 3rdFix All Stop - Inhibited
35
(P0748)
Line Pressure Solenoid
Failure ON - - Stop -
36
(P1860)
Lock-up Duty Solenoid
Failure ON - - - Inhibited
41
(P0731)
1stGearRatioError ON No Fail-safe Function
42
(P0732)
2ndGearRatioError ON No Fail-safe Function
43
(P0733)
3rdGearRatioError ON No Fail-safe Function
44
(P0734)
4thGearRatioError ON No Fail-safe Function
51
(P1750)
Low & Reverse Brake
Fail-safe Valve Failure ON 3rdFix All Stop - Inhibited
52
(P1755)
2-4 Brake Fail-safe Valve
Failure ON 3rdFix All Stop - Inhibited
-
(P0602)
ECU Programming Error ON No Fail-safe Function
*1: When the engine speed is more than 470 rpm for 10 minuets, the lock-up and gear shift to 4th (over-drive) are
allowed.
*2: In case of fail-safe valve failure, gear shift to 4th (over-drive) is inhibited.

7A2-36 DIAGNOSIS (JR405E)
DTC P0722 (Flash Code 11) Vehicle Speed Sensor No Signal


Speed
Sensor
TCM



B13
H23
(4)C95
(13)E30
(2)
(1)
(3)
E10
Key SW
YEL/RED
BLK YEL/RED

Speed Sensor Turbine Sensor

Setting Condition:

When the vehicle speed exceeds 5 km/h with the turbine speed over 1000 rpm for 5 seconds, after 25.5
seconds elapsed in D, 3, 2 or L range.

Fail Safe:

When the vehicle is running, the gear position selected at the trouble detection is held and the lock-up is
inhibited.

After the vehicle stopped, all solenoid operations stop (OFF) and the gear is fixed to the 3rd.

Possible Cause:

Speed sensor malfunction.

Sensor wheel (parking gear) malfunction.

Large sensing gap between speed sensor and sensor wheel (parking gear).

Sensor wire open circuit, short circuit to battery or short circuit to ground between speed sensor terminal 1 and
TCM terminal B13 (C95).

Sensor wire open circuit or short circuit to ground of the harness between speed sensor terminal 2 and power
supply circuit.

Sensor wire open circuit or short circuit to battery between speed sensor terminal 3 and ground circuit.

Poor connection of each connector.