2004 ISUZU TF SERIES lock

7A2-82 DIAGNOSIS (JR405E)
DTC P0602 Programming Error

Setting Condition:

When reprogramming operation is stopped under Service Programming System (SPS).

When non programmed TCM (blank TCM) is used without Service Programming System (SPS).

Fail Safe:

Lock-up is inhibited.

All solenoid operations stop (OFF) and the gear is fixed to the 3rd.

Possible Cause:

Low battery voltage while Service Programming System (SPS) is operated.

No programmed TCM (blank TCM) is used.

Recover DTC:
Reprogram the TCM using with Service Programming System (SPS).

7A2-86 DIAGNOSIS (JR405E)
Symptom Condition Description
Large shock when gear is shifted to 3rd to
4th or 4th to 3rd
Large shock is felt when the accelerator
pedal is stepped on for acceleration and the
gear is shifted up or down.
C14
Large shock when kick-down Large shock is felt when the accelerator
pedal is stepped on for kick-down. C15
Large shock when no acceleration Large shock is felt when the accelerator
pedal is not stepped on. C16
Large shock when gear is shifted down to
2nd to 1st in L range
Large shock is felt when the shift lever is
selected in L range. C17
Large shock (other)
Large shock is felt when the accelerator
pedal is stepped on for acceleration and the
gear is shifted up or down.
C18

Large shock when vehicle speed is downed
by no accelerator pedal or vehicle is
stopped.
Large shock is felt when the accelerator
pedal is not stepped on. C19
Large lock-up shock Large shock is felt at lock-up. C20
Shift down or engine over-run when the
accelerator pedal is stepped on in 4th gear
Shift down or engine over-run above the
kick-down area. C21

DIAGNOSIS (JR405E) 7A2-89
Symptom Condition Description
Faulty during the
running Low maximum speed or poor acceleration Starting acceleration is poor. F1
Acceleration is slow though the accelerator
pedal is stepped on during the running.
Engine races up during acceleration (slip)
The engine speeds up but vehicle speed
does not increase when the accelerator
pedal is stepped on at the starting.
F2

Only the engine speeds up but vehicle
speed does not increase when the
accelerator pedal is stepped on for
acceleration during the running.

Noise or vibration during the running in R, D,
3, 2, or L range
Noise or vibration is generated in the vicinity
of AT during the running. F3
Engine brake does not in apply L range
The engine brake does not apply, allowing
the vehicle to run freely when the
accelerator pedal is released at low speed in
L range.
F4
Engine stalls before vehicle stops from
running
The engine stalls simultaneously with the
vehicle stop when the brake pedal is
stepped on to stop the vehicle during the
running.
F5
Faulty in the
stopping
Vehicle moves in P range, or parking gear is
not disengaged other than P range
Vehicle moves though it stops at a slope
and P range is selected. G1

The engine stalls and vehicle does not move
though other than P range is selected and
the accelerator pedal is stepped on.

Creep force is large
Vehicle accelerates in D, 3, 2, L, and R
ranges though the accelerator pedal is not
stepped on.
G2
Creep force is small Vehicle does not move though a run range
is selected on a flat road during the idling. G3
Large noise during idling with the vehicle in
stop state
The transmission is noisy during the idling
speed in all ranges. G4
Faulty lock-up Judder occurs at the lock-up The vehicle body judders at lock-up. H1
Large lock-up shock Large shock is felt at lock-up. H2
Lock-up point is high or low Lock-up point is excessive high or low. H3
No lock-up No lock-up Lockup is not performed in spite of the lock-
up area. I1

DIAGNOSIS (JR405E) 7A2-97
No. B2: Poor Acceleration at Starting

Description:

Starting acceleration is poor.

Diagnosis Hints:

In addition to the low engine output, faulty gear shifting of AT or fixing at the 3rd position may be possible.
Therefore, in case of such a trouble that "maximum speed is low, and acceleration is poor", it should be cleared
up whether the trouble is originated from the engine system of AT system by a running test, inspection of stall
revolution, etc.

Possible Cause:

Clogged air cleaner, out of injection timing, dropped compression pressure, etc.

Fixing at 3rd position (fail-safe activated).
Since the gear is fixed at the 3rd position because of the fail-safe function, a trouble that "Maximum
speed is low, and acceleration is poor" is resulted. In this case, the DTC is memorized.
When TCM stops operation because of faulty TCM ground, the gear is fixed at the 3rd position because
of a mechanical reason. In this case, no DTC is memorized.

Disordered inhibitor switch.

Incorrect properties of throttle opening signal (serial communication) of throttle position sensor.
Throttle opening signal (serial communication) of the throttle position sensor does not change in
proportion to the throttle opening. In this case, fixing at the high or low gear results in such a trouble
that "Maximum Speed is Low and Acceleration is Poor".

Slip of clutch (low clutch, high clutch).

If slip of clutch is caused, a DTC (gear ratio error) is stored.

Dropped line pressure.

Trouble in the torque converter system (faulty operation).

Step Action Yes No
1 Test Drive.
Is the gear smoothly shifted in the order of 1st to 2nd, 2nd to 3rd,
3rd to 4th gear and lock up?

Clogged air cleaner,
out of injection
timing, dropped
compression
pressure, etc.

Go to Step 2
2 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 3 Go to Step 3
3 Are any DTCs stored?
Go to DTC Chart Go to Step 4

7A2-104 DIAGNOSIS (JR405E)
No. B5: Engine Stalls When Selecting From N Range to
R, D, 3, 2 or L Range

Description:

The engine stalls when selecting from N or P range to a run range during the engine idling.

Diagnosis Hints:

As causes attributable to the engine, faulty idle up, insufficient engine output, etc. are considered.

As a cause of the AT system, faulty lockup piston system (lockup engine stall) is considered.

If the oil through resistance increases remarkably due to clogged oil cooler or some other reason, or if the ATF
level decreases, the lock-up piston works causing the engine stall.

Possible Cause:

Disordered idling speed, faulty idle up, faulty engine output, shortage output.

Insufficient ATF quantity (dropped level).

Clogged oil cooler (foreign substance mixed in).

Faulty lock-up piston (clogged oil passage of solenoid drive circuit, faulty operation).

Step Action Yes No
1 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Check of engine idle up speed
Does the idle speed increase when the air conditioning or other
electric load is turned on?
Go to Step 5
Repair the defect or
replace.

DIAGNOSIS (JR405E) 7A2-105
Step Action Yes No
5 Inspection of electrical or mechanical fault
When the D range is selected from D at idling speed, is the signal
to the lock-up solenoid turned off using the Tech 2 or circuit
tester?
Control Valve

TCM
B17
B23 BLK Lock-up Solenoid

Te rm i n a l
Assembly
VIO Line Pressure Solenoid

E54
(4)
(6)H23
(14)
(6)C95
(17)
(23) BLK
VIO
TCM terminal
Lock-upB17
At lock-up Approx. 2.2 - 9.0 V (AC range)
At unlock-up Approx. 1.0 - 2.0 V (AC range)
Go to Step 6
Find a cause to turn
on the lockup
solenoid
6 Check of clogging of oil cooler
When blowing the oil cooler outlet with air, does some foreign
substance come out?
Clean or replace the
oil cooler.
Go to Step 7
Clogged lock-up
solenoid oil
passage. Faulty
operation of lock-up
piston.
Faulty control valve.
7 Is the stall revolution correct in D, 3, 2 and L range? Refer the
STALL TEST section in this manual.
Go to Step 8
Repair the defect or
replace.
8 Is the line pressure correct? Refer the LINE PRESSURE TEST
section in this manual.
Trouble in the AT
assembly or control
valve.
Repair the defect or
replace.

7A2-114 DIAGNOSIS (JR405E)
No. C12: Large Shock When Gear is Shifted to 1st to 2nd or 2nd
to 1st
No. C13: Large Shock When Gear is Shifted to 2nd to 3rd or 3rd to
2nd
No. C14: Large Shock When Gear is Shifted to 3rd to 4th or 4th to
3rd
No. C15: Large Shock When Kick-down
No. C16: Large Shock When No Acceleration
No. C17: Large Shock When Gear is Shifted Down to 2nd to 1st in
L Range
No. C18: Large Shock (Other)
No. C19: Large Shock When Vehicle Speed is Downed by No
Accelerator Pedal or Vehicle is Stopped

Description:

Large shock is felt when the accelerator pedal is stepped on for acceleration and the gear is shifted up or down.

Large shock is felt when the accelerator pedal is stepped on for kick-down.

Large shock is felt when the accelerator pedal is not stepped on.

Large shock is felt when the shift lever is selected in L range.

Diagnosis Hints:

Basically same causes as "No. C1 - C8: Engine races up (slip)" are considered.






No. C20: Large lock-up shock

Description:

Large shock is felt at lock-up.

Diagnosis Hints:

Out of properties of input sensor or faulty lock-up piston pressure system are considered.

Trouble diagnosis flow is basically the same as "No. I1: No lock-up".






No. C21: Shift Down or Engine Over-run When The Accelerator
Pedal is Stepped on in 4th Gear

Description:

Shift down or engine over-run above the kick-down area.

Diagnosis Hints:

Basically same causes as "No. C1 - C8: Engine races up (slip)" are considered.

DIAGNOSIS (JR405E) 7A2-127
No. F1: Low Maximum Speed or Poor Acceleration

Description:

Starting acceleration is poor.

Acceleration is slow though the accelerator pedal is stepped on during the running.

Diagnosis Hints:

In addition to the low engine output, faulty gear shifting of AT or fixing at the 3rd position may be possible.
Therefore, in case of such a trouble that "maximum speed is low, and acceleration is poor", it should be cleared
up whether the trouble is originated from the engine system of AT system by a running test, inspection of stall
revolution, etc.

Possible Cause:

Clogged air cleaner, out of injection timing, dropped compression pressure, etc.

Fixing at 3rd position (fail-safe activated).
Since the gear is fixed at the 3rd position because of the fail-safe function, a trouble that "Maximum
speed is low, and acceleration is poor" is resulted. In this case, the DTC is memorized.
When TCM stops operation because of faulty TCM ground, the gear is fixed at the 3rd position because
of a mechanical reason. In this case, no DTC is memorized.

Disordered inhibitor switch .

Incorrect properties of throttle opening signal (serial communication) of throttle position sensor.
Throttle opening signal (serial communication) of the throttle position sensor does not change in
proportion to the throttle opening. In this case, fixing at the high or low gear results in such a trouble
that "Maximum Speed is Low and Acceleration is Poor".

Slip of clutch (low clutch, high clutch).

If slip of clutch is caused, a DTC (gear ratio error) is stored.

Dropped line pressure.

Trouble in the torque converter system (faulty operation).

Step Action Yes No
1 Test Drive.
Is the gear smoothly shifted in the order of 1st to 2nd, 2nd to 3rd,
3rd to 4th gear and lock up?
Clogged air
cleaner, out of
injection timing,
dropped
compression
pressure, etc. Go to Step 2
2 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 3 Go to Step 3
3 Are any DTCs stored?
Go to DTC Chart Go to Step 4