2004 ISUZU TF SERIES brakes

BRAKES 5C-41











Thickness of Disc Pad
Thickness (t) mm(in)

Standard Limit
10.0 (0.394) 1.8 (0.071)

Replace the front disc pad whenever the pad wear indicator
makes a squeaking noise or when the pad is worn to within 1.8
mm of the shoe table.

All four brake pads should be replaced together.

302R300019


Seal and Boot
The dust seal, dust boot and ring seal are to be replaced each
time the caliper is overhauled.
Discard thee used rubber parts.

5C-42 BRAKES
REASSEMBLY
CALIPER ASSEMBLY


Disassembly Steps
1. Body ; caliper
2. Ring seal
3. Dust seal ; piston
4. Piston
5. Bleeder
6. Cap





Important Operations
1. Body ; Caliper
2. Ring Seal
Apply clean brake fluid to the ring seal and cylinder wall, then
insert the ring seal into the cylinder.
Ensure that the piston ring seal are not twisted in the caliper
bore grooves.

BRAKES 5C-43

3. Dust seal ; Piston
Install the dust seal on the pistons.
4. Piston
Apply clean brake fluid to the piston, the dust seal is certainly
put into the slot on the piston and attach the caliper.
When inserting the piston into the cylinder, use finger pressure
only. Do not use a mallet or other impact tools, since damage
to the cylinder wall or ring seal can result.
The movement of a caliper piston into a caliper bore should be
smooth and even. If a caliper piston is frozen or difficult to
bottom, the caliper requires overhaul or replacement.
RTW35CSH000701
When not entering with a finger, insert a discarded inner brake
pad (2) or block of wood in front of the pistons. Using 2 large
C-clamps (1) installed over the body of the caliper (3) and
against the brake pad or block of wood, slowly bottom the
pistons evenly into the bores.
Insert the dust seal ring into the dust seal.
CAUTION:
Piston made by plastic material.
Don’t must be hit on the piston by hammer etc. and don’t
grasp to face of piston by pliers.


5. Bleeder
Torque Nm(kgfm/Ibin)
9 – 16 (0.9 – 1.6 / 78 - 139)

6. Cap

5C-44 BRAKES
REAR DRUM BRAKE ASSEMBLY
DISASSEMBLY

First, disassemble the brake drum. Then disassemble the rear brake assembly.
Refer to the “REAR AXLE ” section for the brake drum disassembly procedure.

RTW35CMF000201

MAJOR COMPONENTS
Disassembly Steps

1. Spring ; adjuster
2. Ring ; Adjuster lever
3. Lever ; adjuster

4. Spring ; Shoe hold
5. Pin ; Shoe hold

6. Spring ; Shoe to shoe, lower
7. Adjuster assembly
8. Spring ; shoe to shoe, upper
9. Shoe ; leading

10. Shoe ; trailing
11. Spring ; lever return
12. Retainer
13. Washer ; lever
14. Lever ; parking
15. Bolt ; wheel cylinder
16. Wheel cylinder assembly
17. Cover
18. Back plate

MINOR COMPONENTS
Disassembly Steps
Wheel Cylinder Assembly (14)

19. Piston
20. Cup
21. Boot ; piston

22. Return spring
23. Bleeder
24. Cap ; bleeder

BRAKES 5C-45

P1010008


Important Operations
4. Spring ; shoe hold
Push the shoe hold spring toward the brake shoe and hold it.
Rotate the spring to remove it from the shoe hold pin.


6. Spring ; shoe to shoe, lower
Slide the brake shoes and lower spring toward the ground.
Remove the lower spring.


INSPECTION AND REPAIR
Make necessary correction or parts replacement if wear damage or any other abnormal conditions are found
through inspection.





Brake drum


Back plate


Brake lining


Wheel cylinder body


Piston

Piston cup

Return spring



Visual check
Inspect the following parts for wear scuffs, scratches,
corrosion, stains, deterioration, or other abnormal conditions.





Thickness of the Brake Lining
Thickness mm(in)
standard (T) Limit (t)
4

2 5.0 (0.197) 1.0 (0.039)
4

2 HIGH RIDE
4

4 5.0 (0.197) 1.0 (0.039)

5C-46 BRAKES



Clean wheel Cylinder Parts
Always use clean brake fluid to clean wheel cylinder parts.
Note:
Do not use mineral-vase cleaning solvents such as
gasoline, kerosene, acetone, paint thinner, or carbon
tetrachloride.



Piston Cups
Inspect the piston cups for wear, distortion, fatigue, fatigue or
other abnormal conditions.



Measuring the Brake Drum
mm(in)
Standard Limit
Inside diameter 254 (10.000) 255.5 (10.059)
Run out 0.08 (0.003) 0.15 (0.006)
Inside diameter 295 (11.614) 296.5 (11.673)TFR (HIGH RIDE)
TFS Run out 0.08 (0.003) 0.15(0.006)
TFR

BRAKES 5C-47
REASSEMBLY

RTW35CMF000301

MINOR COMPONENTS
Reassembly Steps
Wheel cylinder Assembly (7)

1. Piston assembly
2. Cup ; piston
3. Return spring



4. Boot ; piston

5. Bleeder
6. Cap ; bleeder

MAJOR COMPONENTS
Reassembly Steps

7. Back plate
8. Cover

9. Wheel cylinder assembly

10. Bolt ; wheel cylinder

11. Shoe ; leading

12. Lever ; parking

13. Washer ; lever

14. Retainer
15. Spring ; lever return



16. Shoe ; trailing

17. Spring ; shoe to shoe, upper

18. Adjust assembly
19. Spring ; shoe to shoe ; lower

20. Lever ; adjuster

21. Ring ; Adjuster lever
22. Spring ; shoe hold

23. Pin ; shoe hold

24. spring ; adjuster

5C-48 BRAKES



Important Operations
Note :


Wash the disassembled parts in clean brake fluid.


Use compressed air to clean the ports.


Protect the disassembled part surfaces from dust and othe
r
foreign material contamination.


Before reassembly, check the part surfaces for dust and
other foreign material contamination.


Be sure to replace the designated parts with new ones.

4. Piston Assembly
Install new piston cups on each piston so that the flared end of
the cups are turned to the inboard side of the pistons.
Attach the return spring and the boot to the piston.
Be sure to use new piston cup and boot.




Apply brake fluid to the piston and the inner face of the
boots.


Note the direction of piston cup.



5. Bleeder ; Wheel Cylinder
Torque Nm(kgfm/Ibin)
6 - 8 (0.6 – 0.8 / 52 - 69)



9. Wheel Cylinder Assembly
10. Bolt ; Wheel cylinder
Torque N
m(kgf
m/Ib
ft)
7 - 11 (0.7 – 1.1 / 61 - 95)