2004 ISUZU TF SERIES switch

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-75


 No detect DTC P1767.

No detect DTC P0560.

No detect DTC P0712, 0713.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring. Inspect
for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.

Inspect the wiring for EMI (Erectro-Magnetic
Interference). Check that all wires are properly
routed away from coil, and generator. Also check fo
r
improperly installed electrical options. When this test
is performed, turn “OFF" on electronic auto parts
switches to improperly for a noise preventing.

ON-VEHICLE SERVICE (AW30–40LE) 7A3-1
TRANSMISSION
ON-VEHICLE SERVICE (AW30–40LE)
CONTENTS

Service Precaution .................................................
7A3-2
Location of Clutch, Brake, One-Way Clutch
and Solenoid ........................................................
7A3-3
Operation of Clutch, Brake and One-Way
Clutch ....................................................................
7A3-4
Trnasmission Indentification ..............................
7A3-4
Speed Change and Lock-Up Pattern ...............
7A3-5
Overdrive and Lock-Up Operating
Conditions ............................................................
7A3-5
Diagnosis .................................................................
7A3-6
Basic Troubleshooting ........................................
7A3-6
Manual Shifting Test ...........................................
7A3-12
Stall Test ..............................................................
7A3-12
Time Lag Test .....................................................
7A3-13
Hydraulic Test ......................................................
7A3-14
Road Test .............................................................
7A3-15
Shift Pont Chart and Lock-Up Point Chart ..........
7A3-19
Shift Pont Chart ...................................................
7A3-19
Lock-Up Point Chart ...........................................
7A3-20
Transmission Fluid Level and Condition .............
7A3-21
Inspection .............................................................
7A3-21
ATF Replacement ..................................................
7A3-22
Inspection .............................................................
7A3-22
Neutral Start Switch (Mode Switch) .....................
7A3-23
Inspection .............................................................
7A3-23
Removal ...............................................................
7A3-23
Installation ............................................................
7A3-23
Brake Signal ............................................................
7A3-24
Inspection .............................................................
7A3-24
Input and Output Revolution Sensor ....................
7A3-25
Inspection .............................................................
7A3-25
Pattern Select Switch .............................................
7A3-25
Inspection .............................................................
7A3-25
Solenoid ...................................................................
7A3-26
Inspection .............................................................
7A3-26

ATF Temperature Sensor ......................................
7A3-27
Inspection .............................................................
7A3-27
Select Lever ....................................................... 7A3-28 Remove or Disconnect .......................................
7A3-28
Install or Connect .................................................
7A3-29
Shift Cable ......................................................... 7A3-31
Remove or Disconnect .......................................
7A3-31
Install or Connect .................................................
7A3-32
Torque specifications ..........................................
7A3-33
Transmission Control Module (TCM) ...................
7A3-34
Removal ................................................................
7A3-34
Installation .............................................................
7A3-34
Shift Solenoid and Lock-Up Solenoid ...................
7A3-35
Removal ................................................................
7A3-35
Installation .............................................................
7A3-36
Valve Body Assembly and Pressure Control Solenoid .................................................
7A3-37
Removal ................................................................
7A3-37
Installation .............................................................
7A3-39
Rear Oil Seal (Adapter Housing, 4

4) .................
7A3-40
Removal ................................................................
7A3-40
Installation .............................................................
7A3-40
Rear Oil Seal (Extension Housing, 4
2) ..............
7A3-41
Removal ................................................................
7A3-41
Installation .............................................................
7A3-41
Transmission Assembly .........................................
7A3-42
Transmission and Associated Parts .................
7A3-42
Removal ................................................................
7A3-43
Installation .............................................................
7A3-46
Major Components ..............................................
7A3-50

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-5

Speed Change and Lock-Up Pattern
If you select a speed as shown below by specifying
respective positions of transmission shift lever, transfe
r
switch and pattern select switch, the transmission
control computer controls speed change and lock-up
operations based on the specified pattern in accordance
with the degree of throttle opening and vehicle speed.
Pattern select sw. position Transmission shift position


D 3 2 L
NORMAL, POWER 1st 
[2nd] 
[3rd] 
[O/D] 1st 
[2nd] 
[3rd] 1st 
2nd
(3rd) 1st
(2nd)
3rd START 3rd fixing — —

[ ]: The lock-up operation is available.
( ): Transmission is shifted at high speed to prevent overrun.


Overdrive and Lock-Up Operating Conditions
The overdrive and lock-up clutch operate if the following
conditions are satisfied.
Overdrive Lock-up clutch
Shift pattern position
NORMAL NORMAL
Transmission shift position
D range 
Brake lamp switch
— OFF
Throttle opening
Fully closed Except fully closed
Accelerator About 52 km/h (32 mph) or more 2nd: About 76 km/h (47 mph) or
more
Vehicle speed Deceleration About 42 km/h (26 mph) or more 3rd: About 56 km/h (35 mph) or more
O/D: About 67 km/h (42 mph) or
more

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-23

Neutral Start Switch (Mode Switch)
Inspection
With a circuit tester, make a continuity test on the
neutral start switch with the moving piece set in each
position.










RTW37BSH000101
Removal
Preparation:
Disconnect negative ( –) battery cable.
1. Remove the rear side ATF cooler pipe from the
transmission elbow.
2. Disconnect neutral start switch connector.
3. Unstake the lock washer, and then remove the shaft
nut.
4. Remove the neutral start switch.
Installation
To install, follow the removal steps in the reverse order,
noting the following points;
If a engine starts at any selector position except “N ” o
r
“ P ”, the neutral start switch (mode switch) should be
adjusted.
1. Loosen the neutral start switch bolt and set the shift
selector to the “N" range.
2. Align the groove and neutral basic line.
3. Hold in position and tighten the bolt and nut.
Torque:
Nut – 7 N 


m (61 Ib in)
Bolt – 13 N 


m (113 Ib in)
4. Lock the nut with the lock washer tubs at two points.



RUW17ASH013601

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-25

Input and Output Revolution Sensor
Inspection

1. Disconnect the input and output revolution sensor
connector.
2. Use an ohmmeter to measure the resistance between terminals 1 and 2.
Standard resistance
Input revolution sensor: 387 – 473






(at 20

 

C,
4

 
2)
, 560
– 680





(at 20

 

C, 4
 
4)
Output revolution sensor: 560 – 680






(at 20

 

C)




F07RY00018



Pattern Select Switch
Inspection
Inspect that there is continuity between each terminals.




RTW37ASH000501

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-43

Removal
NOTE: Before removing transmission and transfer
assembly from vehicle, change the transfer mode to
2WD using the 4WD push button switch on dash panel.
1. Disconnect battery ground cable.
2. Raise and support vehicle with suitable stands.
3. Remove front propeller shaft.(4WD only)
NOTE: Apply alignment marks on the flange at both
front and rear sides.
4. Remove rear propeller shaft.
NOTE: Apply alignment marks on the flange at the
differential side.


401RS023
5. Remove the middle exhaust pipe.



RTW37ASH0001

6. Disconnect the transfer harness connectors and the
clips.(4WD only)

Speed sensor
 2W-4W shift actuator
NOTE: Avoid turning the vehicle ignition switch to the
ON position when the 2WD-4WD connector is removed
(battery connected).
If the ignition switch must be turned to the ON position,
the controller must first be removed (memory must be
cleared because the CHECK 4WD INDICATOR will
light).
7. Support transfer case with a transmission jack.(4WD only)
8. Remove the transfer case assembly from the
transmission.(4WD only)
9. Disconnect the shift cable.
10. Remove the fuel pipe clips with the fuel pipes from the brackets and put aside it. Remove the fuel pipe
brakets from the transmission.






P1010010
11. Discinnect the transmission harness connectors
and clips.
12. Remove the oil level gauge and the guide tube.
13. Remove the suspension crossmember.

UNIT REPAIR (AW30–40LE) 7A4–3
Major Components (1)
Major Components (1) and Associated parts
RTW 37A M F00 0601
E nd O FCallo ut
Disassembly steps
1. Remove the torque converter.
2. Remov e the select lev er.
Legend
(1) Torque converter
(2) Select lever
(3) Neutral start switch (Mode switch)
(4) Elbow
(5) Oil temperature sensor
(6) Breather hose
(7) Input revolution sensor(8) Output revolution sensor (4
4)
(9) Output revolution sensor (4
2)
(10) Speedometer sensor, speedometer driven gear
and plate (4
2)
(11) Extension housing (4
2)
(12) Adapter housing (4
4)
(13) Transmission assembly

7A4–4 UNIT REPAIR (AW30–40LE)
3. Remove the neutral start switch (Mode switch).
Unstake the lock washer.
Remove the nut and bolt, and then remove the
neutral start switch.
Remove the lock washer.
RTW 37BSH00 010 1
4. Remove the two elbows from transmission case.
24 0RY 0 000 1
5. Remove the oil temperature sensor.
6. Remove the breather hose.
7. Remove the Input revolution sensor.
8. Remove the output revolution sensor (4
4).
9. Remove the output revolution sensor (4
2).
10. Remove the speedometer sensor, speedometer
driven gear and plate (4
2).
11. Remove the ex tension housing (4
2).
12. Remove the adapter housing (4
4).13. Remove the transmission assembly.
Install special tool to the transmission unit.
Holding fix ture: J–37227
Holding fix ture base: J–3289–20
RUW3 7A SH00 3001