2004 ISUZU TF SERIES brake

UNIT REPAIR (JR405E) 7A4-23

CONTROL VALVE LOWER BODY

10CV11
Legend
1. Retainer plate, spring, and steel ball
2. Retainer plate, plug, spring, and
pressure regulator valve
3. Retainer plate, spring, and high clutch
accumulator
4. Retainer plate, plug, low and reverse
brake fail valve A, and spring
5. Retainer plate, plug, spring, and fail
valve
6. Retainer plate, plug, low and reverse
brake amp valve, and spring
7. Oil pressure switch
8. Oil filter
9. Solenoid
10. Line pressure solenoid
11. Lock-up solenoid

12. Harness bracket
13. Solenoid fixing plate
14. Harness assembly
15. Retainer plate, plug, spring, and 2-4
brake fail valve A
16. Retainer plate, plug, spring, and low
clutch amp valve B
17. Retainer plate, spring, and torque
converter relief valve
18. Oil strainer
19. Control valve lower body
20. Retainer plate, spring, and 2-4 brake
solenoid accumulator
21. Oil pressure switch

7A4-26 UNIT REPAIR (JR405E)
No. Valve
nomenclature Diameter
(mm / in) Length
(mm / in)Configuration
14 Pressure relief ---- ----

15 Pressure
regulator 16.0 /
0.630 89.5 /
3.524
16 Low and reverse
brake fail (A) 10.0 /
0.394 52.0 /
2.047
17 Fail 12.0 /
0.472 53.5 /
2.106
18 Low and reverse
brake amp 12.0 /
0.472 55.5 /
2.185
19 2 – 4 brake fail
(A) 10.0 /
0.394 65.5 /
2.579
20 Low clutch amp
(B) 12.0 /
0.472 53.0 /
2.087
21 Torque
converter relief 10.0 /
0.394 37.4 /
1.472
22 2 – 4 brake
solenoid
accumulator 14.0 /
0.551 19.5 /
0.768
23 High clutch
accumulator 10.0 /
0.394 31.0 /
1.220

UNIT REPAIR (JR405E) 7A4-27

Spring specifications
No. Valve nomenclature Free length
(mm / in) Outside
diameter (mm
/ in) Linear
diameter (mm
/ in) Number of
coils
14 Pressure relief 49.0 / 1.929 7.6 / 0.299 1.1 / 0.043 17.3
15 Pressure regulator 30.5 / 1.201 14.0 / 0.551 1.4 / 0.055 5.7
16 Low and reverse brake fail (A) 22.0 / 0.866 7.0 / 0.276 0.6 / 0.024 10.0
17 Fail 23.0 / 0.906 11.0 / 0.433 0.5 / 0.020 13.2
18 Low and reverse brake amp 19.5 / 0.768 7.9 / 0.311 0.5 / 0.020 6.9
19 2 – 4 brake fail (A) 24.8 / 0.976 8.5 / 0.335 0.9 / 0.035 7.8
20 Low clutch amp (B) 26.0 / 1.024 11.0 / 0.433 0.5 / 0.020 6.9
21
Torque converter relief More than 47.2
/ 1.858 9.2 / 0.362 1.6 / 0.063 20.2
22 2 – 4 brake solenoid accumulator 31.4 / 1.236 9.8 / 0.386 1.3 / 0.051 9.3
23 High clutch accumulator 51.0 / 2.008 6.5 / 0.256 0.8 / 0.031 23.5

Oil pressure switch
Apply compressed air (392 kPa/4.0 kg/cm2) to the oil pressure
switch to check the oil pressure switch continuity between the
connector and screw.






244L300011

Oil temperature sensor (harness assembly)
Check the oil temperature sensor resistance between harness
terminals 7 and 6 (ground).

Oil temperature sensor resistance: 2,400




2,600 ohms
(20
 )


Solenoid
Measure the resistance of each solenoid.

Resistance:
Brown connector – 3.0
 3.4 ohms (20
 C)
Gray connector – 12.0
 13.2 ohms (20
 C)
White connector – 12.2
 13.4 ohms (20
 C)

Reassembly steps

Coat the parts with ATF before installing them.

Install the control valve to the control valve lower body.

Install the oil filter to the control valve lower body.

UNIT REPAIR (JR405E) 7A4-55
01L&R-CS05
Legend
1. Seal ring
2. Low one-way clutch inner race
3. Return spring
4. Low and reverse brake piston
5. Seal ring
6. Lip seal


7. Transmission case
8. Snap ring
9. Retaining plate
10. Driven plate
11. Drive plate
12. Dish plate



04CASE-AY52

Disassembly steps
1. Harness assembly
Remove the fixing bolt and the harness assembly.

UNIT REPAIR (JR405E) 7A4-57

11CASE-AY01

5. Oil seal
Using a screwdriver, remove the oil seal from the
transmission case.




Inspection
2 – 4 brake drive plate
Measure the 2-4 brake drive plate facing thickness at 3
points and calculate the average value.
If the average value is less than the specified limit, the 2-4
brake drive plate must be replaced.
2 – 4 brake drive plate facing thickness:
Standard = 2.0 mm (0.079 in)
Limit = 1.8 mm (0.071 in)
Low and reverse brake drive plate
Measure the low and reverse brake drive plate facing
thickness at 3 points and calculate the average value.
If the average value is less than the specified limit, the lo
w
and reverse drive plate must be replaced.
Low and reverse brake drive plate facing thickness:
Standard = 2.0 mm (0.079 in)
Limit = 1.8 mm (0.071 in)
2 – 4 brake return spring

Check the number of effective 2-4 brake return spring
coils.
Effective return spring coils (Standard): 10.2

Measure the 2-4 brake return spring outside diameter,
free length, and linear diameter.
If any of the measured values exceed the specified limit,
the 2-4 brake return spring must be replaced.
2 – 4 brake return spring measurements (Standard):
Outside diameter = 6.9 mm (0.272 in)
Free length = 22.5 mm (0.886 in)
Linear diameter = 1.1 mm (0.043 in)
Low and reverse brake return spring

Check the number of effective low and reverse brake
return spring coils.
Effective return spring coils (standard): 4.8

Measure the low and reverse brake return spring outside
diameter, free length, and linear diameter.
If any of the measured values exceed the specified limit,
the low and reverse return spring must be replaced.
Low and reverse brake return spring measurements
(Standard):
Outside diameter = 11.2 mm (0.441 in)

7A4-60 UNIT REPAIR (JR405E)

26L&R01

6. Low and reverse brake piston

Install new seal rings to the low and reverse piston.







RTW47ASH000701
As shown in a figure, sealing lip is attached.

27ASSY004



Install the low and reverse brake piston to the
transmission case.


28ASSY005

7. Return spring

Install the return spring to the low and reverse brake
piston.


29ASSY006

8. Low one-way clutch inner race

Install the low one-way clutch inner race to the
transmission case.

Temporarity tighten the 7 fixing bolts.

UNIT REPAIR (JR405E) 7A4-61

31ASSY074



Tighten each of the bolts a little at a time to the specified
torque.
Be sure that the return spring and the low one-way
clutch inner race installation position does not change as
you tighten the bolts.
Torque: 24 N






m (17 Ib






ft)


32ASSY007

9. Dish plate, driven plate, drive plate, and retaining plate
(low and reverse brake)

Install the dish plate (1) followed by the 6 driven plates
(2) and drive plates (3) sets.


33ASSY008



34ASSY009



35N-SPG02



Install the N-type spring.

7A4-62 UNIT REPAIR (JR405E)





RTW37AMF0001-X



36ASSY10



Install the retaining plate (4).


37ASSY011



Install the snap ring.


38L&R03



Force compressed air (392 kPa/4.0 kg/cm2) through the
oil passages of the transmission case to check low and
reverse brake operation.
If the low and reverse brake does not operate, check the
seal rings for damage and replace if necessary. Also
check that no parts have been installed out of place.