2004 ISUZU TF SERIES battery

7A2-62 DIAGNOSIS (JR405E)
DTC P1860 (Flash Code 36) Lock-up Duty Solenoid Failure

Control Valve

TCM
B17
B23
BLK
Lock-up Solenoid

Terminal
Assembly
VIO
Line Pressure Solenoid

E54 (4)
(6)H23 (14)
(6)C95 (17)
(23)
BLK
VIO


Setting Condition:

The lock-up duty solenoid signal is open circuit or short circuit.
(The voltage different from the output ON/OFF signals was detected while the TCM monitors the solenoid output voltage.)

Fail Safe:

The lock-up is inhibited.

Possible Cause:

Lock-up duty solenoid malfunction.

Open (Off) circuit or short (On) circuit of the lock-up duty solenoid.

Open circuit, short circuit to battery or short circuit to ground between lock-up duty solenoid terminal 4 and TCM
terminal B17 (C95).

Insufficient ground condition of the lock-up duty solenoid.

Poor connection of each connector.

DIAGNOSIS (JR405E) 7A2-65

Setting Condition:

During the running, the low & reverse brake pressure switch does not turn on though hydraulic pressure is
supposed to be generated in the low & reverse brake.
(All pre-setting conditions are met for 2.5 seconds, Low & reverse brake duty solenoid 0% and low & reverse
brake pressure switch off in R range)
Or

During the running, the low & reverse brake switch does not turn off though no hydraulic pressure is supposed to
be generated in the low & reverse brake.
(All pre-setting conditions are met for 2.5 seconds, 4th gear, all pressure switch on and gear ratio 0.652 - 0.735
in D range.)

Fail Safe:

No fail safe function

Possible Cause:

Low & reverse brake duty solenoid malfunction.

Low & reverse brake pressure switch wire open circuit or short circuit.

Open circuit, short circuit to battery or short circuit to ground between low & reverse brake pressure switch
terminal 12 and TCM terminal B12 (C95).

Low & reverse brake hydraulic circuit malfunction in the control valve.

Poor connection of each connector.

Reference:
When the low & reverse brake pressure switch is operated, following signal is outputted.
Measurement terminal: B12 (C95) and B22 (C95)
-At other than R rage or L range in 1st gear: More than 10V
-At R range or L range in 1 st gear: Less than 1V

DIAGNOSIS (JR405E) 7A2-69

Setting Condition:

During the running, the 2-4 brake pressure switch does not turn on though hydraulic pressure is supposed to be
generated in 2-4 brake.
(All pre-setting conditions are met for 2.5 seconds, 2-4 brake pressure switch off, high clutch pressure switch on
and gear ratio more than 0.65 or less than 0.74 with 4th gear in D range.)
Or

During the running, the 2-4 brake switch does not turn off though no hydraulic pressure is supposed to be
generated in the 2-4 brake.
(All pre-setting conditions are met for 2.5 seconds, 2-4 brake pressure switch on in D or N range.)

Fail Safe:

No fail safe function

Possible Cause:

2-4 brake duty solenoid malfunction.

2-4 brake pressure switch wire open circuit or short circuit.

Open circuit, short circuit to battery or short circuit to ground between 2-4 brake pressure switch terminal 7 and
TCM terminal B1 (C95).

2-4 brake hydraulic circuit malfunction in the control valve.

Poor connection of each connector.

Reference:
When the 2-4 brake pressure switch is operated, following signal is outputted.
Measurement terminal: B1 (C95) and B22 (C95)
-At other than 2nd or 4th gear: More than 10V
-At 2nd or 4th gear: Less than 1V

DIAGNOSIS (JR405E) 7A2-73

Setting Condition:

During the running, the high clutch pressure switch does not turn on though hydraulic pressure is supposed to be
generated in high clutch.
(All pre-setting conditions are met for 2.5 seconds, high clutch pressure switch off, 2-4 brake pressure switch on
and gear ratio more than 0.65 or less than 0.74 with 4th gear in D range.)
Or

During the running, the high clutch pressure switch does not turn off though no hydraulic pressure is supposed
to be generated in the high clutch.
(All pre-setting conditions are met for 2.5 seconds, high clutch pressure switch on in P, R or N range.)

Fail Safe:

No fail safe function

Possible Cause:

High clutch duty solenoid malfunction.

High clutch pressure switch open circuit or short circuit.

Open circuit, short circuit to battery or short circuit to ground of the harness between high clutch pressure switch
terminal 1 and TCM terminal B20 (C95).

High clutch hydraulic circuit malfunction in the control valve.

Poor connection of each connector.

Reference:
When the high clutch pressure switch is operated, following signal is outputted.
Measurement terminal: B20 (C95) and B22 (C95)
-At other than 3rd or 4th gear: More than 10V
-At 3rd or 4th gear: Less than 1V

7A2-82 DIAGNOSIS (JR405E)
DTC P0602 Programming Error

Setting Condition:

When reprogramming operation is stopped under Service Programming System (SPS).

When non programmed TCM (blank TCM) is used without Service Programming System (SPS).

Fail Safe:

Lock-up is inhibited.

All solenoid operations stop (OFF) and the gear is fixed to the 3rd.

Possible Cause:

Low battery voltage while Service Programming System (SPS) is operated.

No programmed TCM (blank TCM) is used.

Recover DTC:
Reprogram the TCM using with Service Programming System (SPS).

DIAGNOSIS (JR405E) 7A2-99
Step Action Yes No
6 Inspect the output voltage and throttle opening signal of the throttle
position sensor using a Tech 2 or circuit tester.
Is a voltage value in proportion to the throttle opening output?



TPSTCM
A16
C56
(28)C94
(16) RED/ WHT
C56
(49)
(38)
(57)
(69)ECM
A47 (GND)
A35 (Output)
A26
A55 (+5V)
A69 (I dl e SW)
Go to Step 7
Repair the defect or
replace.
7 Check of power supply to and earth of TCM.
Are the power supply and earth proper?



TCM
A1 (+B)
B5
B15
H23
(15)C95
(5)
(15) BLK/YEL
BLK BLK Battery
C94
(1)
BLK
Go to Step 8
Check the power
source harness and
earth harness (bolt
tightening to the
body).
8 Is the stall revolution correct in D, 3, 2 and L range? Refer the
STALL TEST section in this manual.
Go to Step 6
Repair the defect or
replace.
9 Is the line pressure correct? Refer the LINE PRESSURE TEST
section in this manual. Trouble in the AT
assembly or control
valve.
Repair the defect or
replace.

7A2-102 DIAGNOSIS (JR405E)
Step Action Yes No
6 Inspect the output voltage and throttle opening signal of the
throttle position sensor using a Tech 2 or circuit tester.
Is a voltage value in proportion to the throttle opening output?



TPSTCM
A16
C56
(28)C94
(16) RED/ WHT
C56
(49)
(38)
(57)
(69)ECM
A47 ( GND)
A35 (Out put)
A26
A55 (+5V)
A69 (I dl e SW)
Go to Step 7
Repair the defect or
replace.
7 Check of power supply to and earth of TCM.
Are the power supply and earth proper?



TCM
A1 (+B)
B5
B15
H23
(15)C95
(5)
(15) BLK/YEL
BLK BLK Battery
C94
(1)
BLK
Go to Step 8
Check the power
source harness and
earth harness (bolt
tightening to the
body).
8 Is the stall revolution correct in D, 3, 2 and L range? Refer the
STALL TEST section in this manual.
Go to Step 9
Repair the defect or
replace.
9 Is the line pressure correct? Refer the LINE PRESSURE TEST
section in this manual.
Trouble in the AT
assembly or control
valve.
Repair the defect or
replace.

7A2-110 DIAGNOSIS (JR405E)
Step Action Yes No
6 Inspect the output voltage and throttle opening signal of the
throttle position sensor using a Tech 2 or circuit tester.
Is a voltage value in proportion to the throttle opening output?



TPSTCM
A16
C56
(28)C94
(16) RED/ WHT
C56
(49)
(38)
(57)
(69)ECM
A47 (GND)
A35 (Out put )
A26
A55 (+5V)
A69 (I dl e SW)
Go to Step 7
Repair the defect or
replace.
7 Check of power supply to and earth of TCM.
Are the power supply and earth proper?




TCM
A1 (+B)
B5
B15
H23
(15)C95
(5)
(15) BLK/YEL
BLK BLK Battery
C94
(1)
BLK
Go to Step 8
Check the power
source harness and
earth harness (bolt
tightening to the
body).
8 Is the stall revolution correct in D, 3, 2 and L range? Refer the
STALL TEST section in this manual.
Go to Step 9
Repair the defect or
replace.
9 Is the line pressure correct? Refer the LINE PRESSURE TEST
section in this manual.
Trouble in the AT
assembly or control
valve.
Repair the defect or
replace.