2004 ISUZU TF SERIES reverse

DIAGNOSIS (JR405E) 7A2-101
Step Action Yes No
1 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4

If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Are the engine speed and other engine system correct?
Go to Step 5
Repair the defect or
replace.
5 Inspection of electrical or mechanical fault
Is the signal from each pressure switch changed synchronously?
Control Valve

TCM
B1
B12
B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW
Terminal
Assembly
YEL
E54
(7)
(12)
(1)H23
(12)
(10)C95
(1)
(12)
(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW
High Clutch Pressure SWH22
(8)
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressu re SW)
P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VGo to Step 6
Repair the defect or
replace.

7A2-106 DIAGNOSIS (JR405E)
No. B6: Engine Starter Does Not Run in P or N Range
No. B7: Engine Starter Runs Except in P or N Range

Description:

The engine starter does not run though the P or N range is selected.

The engine starter runs though the R or D, 3, 2or L range is selected.

Possible Cause:

Disordered select cable.

Disordered Inhibitor switch, disconnection or short-circuit of inhibitor switch.


No. B8: Extended Time Lag When Shift Lever is Changed to N to D

Description:

The shift time lag is longer than standard value when shift lever is changed to N to D.

Possible Cause:

Forward range line pressure is low.

Slip of low & reverse clutch.

Slip of low one-way clutch.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Faulty low clutch duty solenoid operation.

Shortage or faulty quality of ATF.


No. B9: Extended Time Lag When Shift Lever is Changed to N to R

Description:

The shift time lag is longer than standard value when shift lever is changed to N to R.

Possible Cause:

Reverse range line pressure is low.

Slip of low & reverse brake.

Slip of reverse clutch.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Faulty low & reverse brake duty solenoid operation.

Shortage or faulty quality of ATF.

DIAGNOSIS (JR405E) 7A2-107
No. B10: Brake is Applied in R Range

Description:

Brake is applied suddenly in R range.

Diagnosis Hints:

Basically a trouble in the AT main unit. However, some trouble in the sensor system or output system may have
some influence on the trouble in the main unit and therefore these systems should be also checked to prevent
reproduce of the trouble.

Possible Cause:

Seized clutch (low clutch, high clutch, 2-4 brake).

Shortage or faulty quality of ATF.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Disordered select cable (select indicator light indicates R but the hydraulic system is not in the R range).

Malfunction of parking mechanism.


No. B11: Insufficient Starting or Shaking in D Range

Description:

Insufficient starting or shaking in D range.

Possible Cause:

Slip of clutch (low clutch, low one-way clutch, reverse clutch, low & reverse brake).
If slip of clutch is caused, a DTC (gear ratio error) is stored.

Shortage or faulty quality of ATF.

Dropped line pressure.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).


No. B12: Noise or Vibration is Generated at Starting

Description:

Noise or vibration is generated in the vicinity of AT at starting.

Diagnosis Hints:

Cause other than AT can be also considered. It is effective means to reproduce a running condition using a lift
up, chassis dynamo, etc. to investigate the origin (generating condition) of noise and vibration.
Caution:
Lifting up some unit to test it accompanies danger. Provide safety measures as far as possible and
carry out the test with sufficient care.

Possible Cause:
Following sources of noise or vibration other than the AT can be considered.

Noise from differential gears.

Noise from propeller shaft.

The bearing support in the middle of the propeller shaft has fatigued, and the bend angle of the propeller shaft
has changed, causing vibration at the time of start.

Unbalanced and poor uniformity of tires cause vibration.

DIAGNOSIS (JR405E) 7A2-109
Step Action Yes No
1 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Are the engine speed and other engine system correct?
Go to Step 5
Repair the defect or
replace.
5 Inspection of electrical or mechanical fault
Is the signal from each pressure switch changed synchronously?
Control Valve

TCM
B1
B12
B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW
Terminal
Assembly
YEL
E54
(7)
(12)
(1)H23
(12)
(10)C95
(1)
(12)
(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW
High Clutch Pressure SWH22
(8)
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressu re SW)
P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10V
Go to Step 6
Repair the defect or
replace.

7A2-112 DIAGNOSIS (JR405E)
Step Action Yes No
1
Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 2 Go to Step 2
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is
low, replenish up to
the specified level.

Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of
the clutch is
supposed.
Overhaul the AT
unit.
4 Are the engine speed and other engine system correct?
Go to Step 5
Repair the defect or
replace.
5 Inspection of electrical or mechanical fault
Is the signal from each pressure switch changed synchronously?
Control Valve

TCM
B1
B12
B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW
Te r m i n a l
Assembly
YEL
E54
(7)
(12)
(1)H23
(12)
(10)C95
(1)
(12)
(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW
High Clutch Pressure SWH22
(8)
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressure SW)
P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VGo to Step 6
Repair the defect or
replace.

DIAGNOSIS (JR405E) 7A2-117
Step Action Yes No
5 Inspection of electrical or mechanical fault
Is signal to each solenoid and pressure switch changed
synchronously to the faulty gear shift?

Control Valve


TCM


B1





B12





B20 RED/YEL
WHT/BLK 2-4 Brake Pressure SW

Terminal
Assembly
YEL
E54

(7)





(12)





(1) H23

(12)





(10)C95

(1)





(12)





(20) RED/YEL
YEL
WHT/BLK
L&R Brake Pressure SW

High Clutch Pressure SW

H22

(8)
Control Valve

TCM
B6
B7
B8
B9
B22 (GND) BLU/BLK
WHT/BLU L&R Brake Solen oid

Te r m i n a l
Assembly
BLK/YEL
RED
2-4 Brake Solenoid

High Clutch Solenoid

Low Clu tch S olen oid

E54
(5)
(9)
(10)
(3)
(11)H23
(11)
(5)
(7)
(2)
(1)
GRY/REDC95
(6)
(7)
(8)
(9)
(22) BLU/BLK
BLK/YEL
RED
WHT/BLU
GRY/RED
Range TCM terminal
GearB20
(High clutch
pressure SW)B1
(2-4 brake pressure
SW)B12 (Low & reverse
brake pressure SW)P - More than 10V More than 10V More than 10VR Reverse More than 10V More than 10V -N - More than 10V More than 10V More than 10VD, 3, 2 1st More than 10V More than 10V More than 10V2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10VL 1st More than 10V More than 10V -2nd More than 10V - More than 10V3rd - More than 10V More than 10V4th - - More than 10V
Range TCM terminal
GearB8
(High clutch
solenoid)B9
(Low clutch
solenoid)B7
(2 -4 b rake
solenoid)B6
(Lo w & reve rs e
brake solenoid)P - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)Approx. 6.2V
(AC ra ng e)
R Reverse Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)-
N - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
D, 3, 2 1st Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
2nd Approx. 6.8V
(AC range)- - Approx. 6.8V
(AC ra ng e)
3rd - - Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
4th - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC ra ng e)
L 1st Approx. 6.8V
(AC range)- Approx. 6.8V
(AC range)-
2nd Approx. 6.8V
(AC range)- - Approx. 6.8V
(AC ra ng e)
3rd - - Approx. 6.8V
(AC range)Approx. 6.8V
(AC ra ng e)
4th - Approx. 6.8V
(AC range)- Approx. 6.8V
(AC ra ng e)
Go to Step 6
In case of fault in
the machine
system, repair that
portion or replace
the unit.
Slip of clutch or fault
of control valve.

7A2-130 DIAGNOSIS (JR405E)
No. F2: Engine Races Up During Acceleration (Slip)

Description:

The engine speed up when the accelerator pedal is stepped on for acceleration and the gear is shifted up or
down.

Only the engine speeds up but vehicle speed does not increase when the accelerator pedal is stepped on for
acceleration during the running.

Diagnosis Hints:

Basically same causes as "No. C1 - C8: Engine races up (slip) by shift up or shift down" are considered.
When the condition of No. C1-C8 grows worse, symptom of No. F2 results.




No. F3: Noise or Vibration During the Running in R, D, 3, 2 or L Range

Description:

Noise or vibration is generated in the vicinity of AT during the running.

Diagnosis Hints:

Cause other than AT can be also considered. It is effective means to reproduce a running condition using a lift
up, chassis dynamo, etc. to investigate the origin (generating condition) of noise and vibration.
Caution:
Lifting up some unit to test it accompanies danger. Provide safety measures as far as possible and
carry out the test with sufficient care.

Possible Cause:
Following sources of noise or vibration other than the AT can be considered.

Noise from differential gears.

Noise from propeller shaft.

The bearing support in the middle of the propeller shaft has fatigued, and the bend angle of the propeller shaft
has changed, causing vibration at the time of start.

Unbalanced and poor uniformity of tires cause vibration.




No. F4: Engine Brake Does Not Apply in L Range

Description:

The engine brake does not apply, allowing the vehicle to run freely when the accelerator pedal is released at low
speed in L range.

Possible Cause:

Slip of clutch (low & reverse brake)
If slip of clutch is caused, a DTC (gear ratio error) is stored.

Faulty input/output signal system.
Low & reverse brake duty solenoid

Faulty control valve (faulty operation, sticking).

DIAGNOSIS (JR405E) 7A2-139
No. Z11: Abnormal Oil Pressure

Description:

Oil pressure is low or high.

Possible Cause:

Basically, the same cause as "No. C1 - C8: Engine races up (slip) by shift up or shift down" is considered.

In case of oil pressure is low, faulty oil pump is considered.




No. Z12: Reverse Buzzer Does Not Ring

Description:

Reverse buzzer does not ring in R range.

Possible Cause:

Disordered select cable.

Disordered select lever.

Disordered inhibitor switch.