2004 ISUZU TF SERIES oil pressure

7A2-20 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)




RTW37ALH000101

Once the test vehicle has been identified an
“ Application (Powertrain) Menu" screen appears.
Please select the appropriate application.
The following table shows, which functions are used fo
r
the available equipment versions.



F0: Diagnostic Trouble Codes

F0: Read DTC Info As stored By ECU

F1: Clear DTC Information

F2: DTC Information
F1: Data Display
F2: Snap Shot
F3: Miscllaneous Tests

F0: Lamps

F0: Power Lamp Test
F1: 3rd start Lamp Test
F2: AT Oil Temperature Lamp
F3: Check Light
F1: Solenoids

F0: Shift solenoid A (S1)
F1: Shift Solenoid B (S2)
F2: Pressure Control Solenoid (PCS)

7A2-22 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

TRANSMISSION DATA
ITEM UNIT ENGIN RUNNING AT IDLE
Current Gear 1 st/2 nd/3 rd/4 th 1 st
Target Gear 1 st/2 nd/3 rd/4 th 1 st
Vehicle Speed km/h 0 km/h
AT Output Speed (Automatic Transmission) RPM 0 RPM
AT Input Speed (Automatic Transmission) RPM 675725 RPM
Engine Speed RPM 675725 RPM
Throttle Position Sensor Signal % 0.007.00%
AT Oil Temperature (Automatic Transmission) C Depends on conditions
TCM Status Transfer Low /Transfer High Transfer HI
Desired PC Solenoid Pressure (STH) kPa 34.397.0 kPa
Desired PC Solenoid Current (STH) mA 8351020 mA
PC Solenoid Actual Current (STH) mA 8351020 mA
Gear Ratio : 1 Depends on uper hood
TCC Slip Speed RPM 0 RPM
Shift Position Actual P/R/N/L/2/3 P
Inhibitor Switch P/R/N/L/2/3 P
Transmission Check Light On/Off Off
AT Oil Temperature Lamp (Automatic
Transmission) On/Off Off
3 rd Start Lamp On/Off Off
Power Lamp On/Off Off
Shift Solenoid S1 On/Off On
Shift Solenoid S2 On/Off On
Shift Solenoid S3 On/Off Off
Diag Switch Condition On/Off Off
Power Switch On/Off Off
Brake Switch On/Off Off
Cruise Switch On/Off Off
4L Signal On/Off Off
3 rd Start Switch On/Off Off
Coolant Temperature C Depends on conditions
Torque Request (timing Retard) CA 0 CA
Garage Shift Mode On/Off Off
CAN TPS % 0.00%
CAN Signal Valid Counter (ECM)
— 0  255
CAN Signal Valid Counter (TCM) — 0  255

7A2-34 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

TCM Diagnostic Trouble Codes
The following table lists the diagnostic trouble codes supported by this vehicle application. If any DTCs not listed here
are displayed by a scan tool, the scan tool data may by faulty; notify the scan tool manufacture of any DTCs
displayed that are not included in the following table.
DTC
NUMBER FLASH
CODE DTC NAME
“CHECK
TRANS"
P0560 25 System Voltage Error —
P0602 63 Transmission Control Module (TCM) Programming Error —
P0705 17 Transmission Range Sensor Circuit Malfunction ON
P0712 15 Transmission Oil Temperature Sensor Circuit Low Input ON
P0713 16 Transmission Oil Temperature Sensor Circuit Hight Input ON
P0717 14 Input Speed Sensor Signal Error ON
P0722 11 Output Speed Sensor Signal Error ON
P0743 33 Torque Converter Clutch Electrical ON
P0748 35 Pressure Control Solenoid Electrical ON
P0753 31 Shift Solenoid S1 Electrical ON
P0758 32 Shift Solenoid S2 Electrical ON
P1767 67 ECM CAN (Control Area Network) Invalid ON
P1790 61 Transmission Control Module ROM Checksum Error ON
P1791 62 Transmission Control Module RAM Error ON
U2104 65 CAN (Control Area Network) BUSS OFF ON

ON-VEHICLE SERVICE (AW30–40LE) 7A3-1
TRANSMISSION
ON-VEHICLE SERVICE (AW30–40LE)
CONTENTS

Service Precaution .................................................
7A3-2
Location of Clutch, Brake, One-Way Clutch
and Solenoid ........................................................
7A3-3
Operation of Clutch, Brake and One-Way
Clutch ....................................................................
7A3-4
Trnasmission Indentification ..............................
7A3-4
Speed Change and Lock-Up Pattern ...............
7A3-5
Overdrive and Lock-Up Operating
Conditions ............................................................
7A3-5
Diagnosis .................................................................
7A3-6
Basic Troubleshooting ........................................
7A3-6
Manual Shifting Test ...........................................
7A3-12
Stall Test ..............................................................
7A3-12
Time Lag Test .....................................................
7A3-13
Hydraulic Test ......................................................
7A3-14
Road Test .............................................................
7A3-15
Shift Pont Chart and Lock-Up Point Chart ..........
7A3-19
Shift Pont Chart ...................................................
7A3-19
Lock-Up Point Chart ...........................................
7A3-20
Transmission Fluid Level and Condition .............
7A3-21
Inspection .............................................................
7A3-21
ATF Replacement ..................................................
7A3-22
Inspection .............................................................
7A3-22
Neutral Start Switch (Mode Switch) .....................
7A3-23
Inspection .............................................................
7A3-23
Removal ...............................................................
7A3-23
Installation ............................................................
7A3-23
Brake Signal ............................................................
7A3-24
Inspection .............................................................
7A3-24
Input and Output Revolution Sensor ....................
7A3-25
Inspection .............................................................
7A3-25
Pattern Select Switch .............................................
7A3-25
Inspection .............................................................
7A3-25
Solenoid ...................................................................
7A3-26
Inspection .............................................................
7A3-26

ATF Temperature Sensor ......................................
7A3-27
Inspection .............................................................
7A3-27
Select Lever ....................................................... 7A3-28 Remove or Disconnect .......................................
7A3-28
Install or Connect .................................................
7A3-29
Shift Cable ......................................................... 7A3-31
Remove or Disconnect .......................................
7A3-31
Install or Connect .................................................
7A3-32
Torque specifications ..........................................
7A3-33
Transmission Control Module (TCM) ...................
7A3-34
Removal ................................................................
7A3-34
Installation .............................................................
7A3-34
Shift Solenoid and Lock-Up Solenoid ...................
7A3-35
Removal ................................................................
7A3-35
Installation .............................................................
7A3-36
Valve Body Assembly and Pressure Control Solenoid .................................................
7A3-37
Removal ................................................................
7A3-37
Installation .............................................................
7A3-39
Rear Oil Seal (Adapter Housing, 4

4) .................
7A3-40
Removal ................................................................
7A3-40
Installation .............................................................
7A3-40
Rear Oil Seal (Extension Housing, 4
2) ..............
7A3-41
Removal ................................................................
7A3-41
Installation .............................................................
7A3-41
Transmission Assembly .........................................
7A3-42
Transmission and Associated Parts .................
7A3-42
Removal ................................................................
7A3-43
Installation .............................................................
7A3-46
Major Components ..............................................
7A3-50

7A3-14 ON-VEHICLE SERVICE (AW30 –40LE)

Measure Time Lag
1. Fully apply the parking brake.
2. Start the engine. Check idling speed (A/C OFF).
3. Shift the shift lever from “N" to “D" range. Using a
stopwatch, measure the time it takes from shifting
the lever until the shock is felt.
Time lag: Less than 0.7 seconds
4. In same manner, measure the time lag for “N"


“R".
Time lag: Less than 1.2 seconds
Evaluation
1. If “N" 
“ D" time lag is longer than specified:

Line pressure too low
 Forward clutch malfunction
 No.2 one-way clutch not operating properly
2. If “N" 
“ R" time lag is longer than specified:

Line pressure too low
 Direct clutch malfunction
 No.3 brake malfunction
3. If both time lag is longer than specified:

Line pressure too low

Hydraulic Test



RUW37ALH000201
Preparation

1. Warm up the transmission fluid.
2. Remove the transmission case test plug and mount the hydraulic pressure gauge.
Oil pressure gauge: J –29770 –A
NOTE: Perform the test at normal operation fluid
temperature (50 – 80 
C or 122 – 176 
F).

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-15

Measure Line Pressure
1. Fully apply the parking brake and chock the four
wheels.
2. Start the engine and check idling rpm.
3. Shift into “D" range, step down strongly on the brake
pedal with your left foot and, while manipulating the
accelerator pedal with the right foot, measure the
line pressures at the engine speeds specified in the
table.
4. In the same manner, perform the test in “R" range.


Line pressure kPa (kg/cm2/psi) Engine
speed “D" range “R" range
Idling 323 – 382
(3.3 – 3.9/47 – 55) 500 – 598
(5.1 – 6.1/73 – 87)
Stall 1,137 – 1,274 (11.6–13.0/165–185) 1,499 – 1,833
(15.3–18.7/218–266)
Evaluation
1. If the measured values at all ranges are higher than
specified:

Pressure control solenoid defective
 Primary regulator valve defective
2. If the measured values at all ranges are lower than
specified:

Primary regulator valve defective
 Oil pump defective
 Pressure control solenoid defective
3. If pressure is low in “D" range only:

“ D" range circuit fluid leakage
4. If pressure is low in “R" range only:

“ R" range circuit fluid leakage
Road Test
NOTE: Perform the test at normal operation fluid
temperature (50 – 80 
C or 122 – 176 
F).
“D" Range Test in “NORMAL", and
“POWER" Pattern Ranges
Shift into the “D" range and hold the accelerator pedal
constant at the 50% and 100% throttle valve opening
positions.
Push in one of the pattern selector buttons and check
the following:

1. 1 –2, 2 –3, 3 –OD and lock-up, up-shifts should take
place, and shift points should conform to those
shown in the automatic shift diagram.


RUA370MH000101




RUA37ASH000101

7A3-26 ON-VEHICLE SERVICE (AW30 –40LE)

Solenoid
Inspection

1. Resistance check

Using an ohmmeter, check the resistance
between each terminals (S1/S2/SL) and body.
Solenoid S1, S2 and lock-up solenoid SL
resistance:
11 – 15






(at 20
 
C)
(Reference) 12 – 16






(at 40
 
C)

Using an ohmmeter, check the resistance
between each terminals (STH) and (STHG).
Pressure control solenoid resistance:
5 – 5.6






(at 20
 
C)
(Reference) 5.4 – 6.1






(at 40
 
C)



220L100001
NOTE: If the pressure control solenoid resistance is not
within speciation, replace the valve body assembly.



2. Operation check
Check the solenoid operation by blowing into an oil
hole as shown in the figure.
Solenoid S1 and S2 (Normal close type)


When battery terminal is disconnected No air leaks
When battery terminal is
connected Air passes through

Lock-up solenoid SL (Normal open type)



When battery terminal is disconnected Air passes through
When battery terminal is
connected No air leaks





244RX00001




244RY00005

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-37

Valve Body Assembly and Pressure Control Solenoid





244RY00009
Removal
Preparation:


Disconnect negative ( –) battery cable.
 Drain the fluid.
Refer to ATF REPLACEMENT in this section.
1. Remove the nineteen bolts and oil pan.