2004 ISUZU TF SERIES key

IMMOBILIZER SYSTEM 11A-41

Step Action Value(s) Yes No
9 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Go to Step 10 
10 Check the immobilizer programming functions.

Immobilizer control unit (ICU).


All transponder (Key).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 11

11 Recheck the DTC.
1. Key position is “OFF” and keep the position for more
than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0003 stored? 
Go to Step 12
Verify repair
12 Replace the transponder (Key).
IMPORTANT:
The replacement transponder (key) must
be programmed the security data by scan tool.
Was the action complete? 
Verify repair 

11A-42 IMMOBILIZER SYSTEM

B0004 IMMOBILIZER COIL CIRCUIT (ANTENNA COIL FAULT)
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed? 
Go to Step 2
Go to Immobilizer
System Check
2 Check the immobilizer coil (antenna) circuit.
1. Key position is “OFF”.
2. Disconnect the immobilizer control unit (ICU).
(immobilizer coil circuit : 3 pin connector)
3. Check the immobilizer coil circuit for an open, short
to ground, or short to voltage.
Also, check the ICU ignition feed circuit for an open or
short to ground and the ICU ground circuit for an
open.
Was a problem found? 
Go to Step 3
Go to Step 4
3 Repair or replace the immobilizer coil (antenna).
Was the action complete? 
Verify repair 
4 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0004 stored? 
Go to Step 5
Verify repair
5 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair


IMMOBILIZER SYSTEM 11A-43

B0005 COMMUNICATION LINE W VOLTAGE LOW
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed? 
Go to Step 2
Go to Immobilizer
System Check
2 Recheck the DTC.
1. Key position is “OFF”.
2. Install the scan tool on vehicle.
3. Key position is “ON”.
4. Check the DTC on scan tool.
Is DTC B0005 stored? 
Go to Step 3
Refer to
Diagnostic Aids
3 Check the immobilizer communication W line circuit.
1. Key position is “OFF”.
2. Disconnect the immobilizer control unit (ICU).
3. Disconnect the engine control module (ECM).
4. Check the immobilizer communication W line
circuit for an open, short to ground, or short to
voltage.
Also, check the ICU and ECM ignition feed circuits for
an open or short to ground and the ICU and ECM
ground circuit for an open.
Was a problem found? 
Go to Step 4
Go to Step 5
4 Repair or replace the immobilizer communication W
line circuit.
Was the action complete? 
Verify repair 
5 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair 

11A-44 IMMOBILIZER SYSTEM

B0006 COMMUNICATION LINE W VOLTAGE HIGH
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed? 
Go to Step 2
Go to Immobilizer
System Check
2 Recheck the DTC.
1. Key position is “OFF”.
2. Install the scan tool on vehicle.
3. Key position is “ON”.
4. Check the DTC on scan tool.
Is DTC B0006 stored? 
Go to Step 3
Refer to
Diagnostic Aids
3 Check the immobilizer communication W line circuit.
1. Key position is “OFF”.
2. Disconnect the immobilizer control unit (ICU).
3. Disconnect the engine control module (ECM).
4. Check the immobilizer communication W line
circuit for an open, short to ground, or short to
voltage.
Also, check the ICU and ECM ignition feed circuits for
an open or short to ground and the ICU and ECM
ground circuit for an open.
Was a problem found? 
Go to Step 4
Go to Step 5
4 Repair or replace the immobilizer communication W
line circuit.
Was the action complete? 
Verify repair 
5 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair 

IMMOBILIZER SYSTEM 11A-45

B0007 NO ENGINE REQUEST RECEIVED
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed? 
Go to Step 2
Go to Immobilizer
System Check
2 Recheck the DTC on ICU.
1. Key position is “OFF”.
2. Install the scan tool on vehicle.
3. Key position is “ON”.
4. Check the DTC on scan tool.
Is DTC B0007 stored? 
Go to Step 3
Refer to
Diagnostic Aids
3 Check the immobilizer communication line circuit.
1. Key position is “OFF”.
2. Disconnect the immobilizer control unit (ICU).
3. Disconnect the engine control module (ECM).
4. Check the immobilizer communication line circuit
for an open, short to ground, or short to voltage.
Also, check the ICU and ECM ignition feed circuits for
an open or short to ground and the ICU and ECM
ground circuit for an open.
Was a problem found? 
Go to Step 4
Go to Step 5
4 Repair or replace the immobilizer communication line
circuit.
Was the action complete? 
Verify repair 
5 Recheck the DTC on ICU.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0007 stored? 
Go to Step 6
Verify repair
6 Recheck the DTC on ECM.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Are below DTCs stored?
P1649 (6VE1, C24SE) , P1611/P1614 (4JH1-TC) 
Go to Step 7
Go to Step 9
7 Perform the immobilizer programming functions.
(Refer to "Important information on Programming")


Engine control module (ECM).
Was the action complete? 
Go to Step 8
Go to Step 11
8 Recheck the DTC on ECM.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Are below DTCs stored?
P1649 (6VE1, C24SE) , P1611/P1614 (4JH1-TC) 
Go to Step 11
Go to Step 12

11A-46 IMMOBILIZER SYSTEM

Step Action Value(s) Yes No
9 Check the immobilizer programming functions.

Engine control module (ECM).
If a problem is found, repair as necessary.
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 10
Go to Step 11
10 Recheck the DTC on ECM.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Are below DTCs stored?
P1649 (6VE1, C24SE), P1611/P1614 (4JH1-TC) 
Go to Step 11
Go to Step 12
11 Replace the engine control module (ECM).
IMPORTANT:
The replacement ECM must be
programmed the security data by scan tool.
Was the action complete? 
Go to Step 12 
12 Recheck the DTC on ECM.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Are below DTCs stored?
P1626 (6VE1, C24SE), P1612/P1613 (4JH1-TC) 
Go to Step 13
Go to Step 2
13 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair


IMMOBILIZER SYSTEM 11A-47

B0008 WRONG TRANSPONDER KEY
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed? 
Go to Step 2
Go to Immobilizer
System Check
2 Check the key.
Is a key peculiar to a vehicle? 
Go to Step 3
Refer to
Diagnostic Aids
3 Check the immobilizer programming functions.


Transponder (Key).
Was a problem found? 
Go to Step 4
Go to Step 5
4 Perform the immobilizer programming functions.

Transponder (Key).
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 5 
5 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0008 stored? 
Go to Step 6
Verify repair
6 Replace the transponder (Key).
IMPORTANT
: The replacement transponder (key)
must be programmed the security data by scan tool.
Was the action complete? 
Go to Step 7 
7 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0008 stored? 
Go to Step 8
Verify repair
8 Replace the immobilizer control unit (ICU).
IMPORTANT
: The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair


11A-48 IMMOBILIZER SYSTEM

B0009 NO TRANSPONDER KEY PROGRAMMED
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed? 
Go to Step 2
Go to Immobilizer
System Check
2 Check the key.
Is a key peculiar to a vehicle? 
Go to Step 3
Refer to
Diagnostic Aids
3 Check the immobilizer programming functions.


Transponder (Key).
Was a problem found? 
Go to Step 4
Go to Step 5
4 Perform the immobilizer programming functions.


Transponder (Key).
(Refer to "Important information on Programming")
Was the action complete? 
Go to Step 5 
5 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0009 stored? 
Go to Step 6
Verify repair
6 Replace the transponder (Key).
IMPORTANT:
The replacement transponder (key)
must be programmed the security data by scan tool.
Was the action complete? 
Go to Step 7 
7 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0009 stored? 
Go to Step 8
Verify repair
8 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair