2004 ISUZU TF SERIES key

IMMOBILIZER SYSTEM 11A-57

B0023 IMMOBILIZER COIL CIRCUIT (ANTENNA COIL FAULT)
(Only 4JA1-T Engine)
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed? 
Go to Step 2
Go to Immobilizer
System Check
2 Check the immobilizer coil (antenna) circuit.
1. Key position is “OFF”.
2. Disconnect the immobilizer control unit (ICU).
(immobilizer coil circuit : 3 pin connector)
3. Check the immobilizer coil circuit for an open, short
to ground, or short to voltage.
Also, check the ICU ignition feed circuit for an open or
short to ground and the ICU ground circuit for an
open.
Was a problem found? 
Go to Step 3
Go to Step 4
3 Repair or replace the immobilizer coil (antenna).
Was the action complete? 
Verify repair 
4 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0023 stored? 
Go to Step 5
Verify repair
5 Replace the immobilizer control unit (ICU).
IMPORTANT:
The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair 

11A-58 IMMOBILIZER SYSTEM

B0024 WRONG TRANSPONDER KEY (Only 4JA1-T Engine)
Step Action Value(s) Yes No
1
W as the "Immobilizer System Check" performed?

Go to Step 2
Go to Immobilizer
System Check
2 Check the key.
Is a key peculiar to a vehicle?

Go to Step 3
Refer to
Diagnostic Aids
3 Check the immobilizer programming functions.

Transponder (Key).
W as a problem found?

Go to Step 4
Go to Step 5
4 Perform the immobilizer programming functions.
 Transponder (Key).
(Refer to "Important information on Programming")
W as the action complete?

Go to Step 5

5 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0024 stored?

Go to Step 6
Verify repair
6 Replace the transponder (Key).
IMPORTANT
: The replacement transponder (key)
must be programmed the security data by scan tool.
Was the action complete?

Go to Step 7

7 Recheck the DTC.
1. Key position is “OFF” and keep the position for
more than 30 seconds.
2. Key position is “ON”.
3. Check the DTC on scan tool.
Is DTC B0024 stored?

Go to Step 8
Verify repair
8 Replace the immobilizer control unit (ICU).
IMPORTANT
: The replacement ICU must be
programmed the security data by scan tool.
W as the action complete?

Verify repair

IMMOBILIZER SYSTEM 11A-59

B0055 EEPROM ERROR
Step Action Value(s) Yes No
1
Was the "Immobilizer System Check" performed? 
Go to Step 2
Go to Immobilizer
System Check
2 Recheck the DTC.
1. Key position is “OFF”.
2. Install the scan tool on vehicle.
3. Key position is “ON”.
4. Check the DTC on scan tool.
Is DTC B0055 stored? 
Go to Step 3
Refer to
Diagnostic Aids
3 Check the immobilizer control unit (ICU) circuit.
1. Ignition "OFF," disconnect the ICU.
2. Check the ICU circuit for an open, short to ground,
or short to voltage.
Also, check the ICU ignition feed circuit for an open or
short to ground and the ICU ground circuit for an
open.
Was a problem found? 
Go to Step 4
Go to Step 5
4 Repair or replace the immobilizer unit (ICU) circuit.
Was the action complete? 
Verify repair

5 Replace the immobilizer control unit (ICU).
IMPORTANT: The replacement ICU must be
programmed the security data by scan tool.
Was the action complete? 
Verify repair 

ANTITHEFT SYSTEM 11B – 1
SECTION 11B
ANTITHEFT SYSTEM
CONTENTS
PAGE
Service Precaution ........................................................................................................ 11B – 3
General Description ...................................................................................................... 11B – 4
Activating the anti-theft system.............................................................................. 11B – 4
Antitheft system alarm operating conditions ........................................................ 11B – 4
Function of a keyless entry system ......................................................................... 11B – 4
Status LED ................................................................................................................. 11B – 4
Hazard relay ............................................................................................................... 11B – 4
Switches .................................................................................................................... 11B – 4
Receiver......................................................................................................................11B – 5
Range of communication ......................................................................................... 11B – 5
Diagnosis ................................................................................................................... 11B – 5
Transmitter (into remote key) .................................................................................. 11B – 5
Transmitter (into remote key) power ...................................................................... 11B – 5
Super lock .................................................................................................................. 11B – 5
No proper transmitter is available, what should be done for the system ?........ 11B – 6
DIAGRAMS AND SCHEMATICS ................................................................................... 11B – 7
SYSTEM WIRING DIAGRAMS .................................................................................. 11B – 7
COMPONENT WIRING LOCATORS (LHD) ............................................................... 11B – 8
WIRING DIAGRAM (LHD).......................................................................................... 11B – 9
WIRING DIAGRAM (LHD).......................................................................................... 11B – 10
WIRING DIAGRAM (LHD).......................................................................................... 11B – 11
WIRING DIAGRAM (LHD).......................................................................................... 11B – 12
WIRING DIAGRAM (RHD with keyless) ................................................................... 11B – 13
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 14
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 15
WIRING DIAGRAM (RHD) ......................................................................................... 11B – 16
WIRING DIAGRAM (RHD) ......................................................................................... 11B – 17
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 18
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 19
WIRING DIAGRAM (Super Lock).............................................................................. 11B – 20
Antitheft control unit (A) .......................................................................................... 11B – 21

11B – 2 ANTITHEFT SYSTEM
Pin-outs ......................................................................................................................11B – 21
Pin- Assignment ........................................................................................................ 11B – 22
lmportant information on Programming .................................................................... 11B – 23
Security code ............................................................................................................. 11B – 23
Entering a code ......................................................................................................... 11B – 23
Tech-2 Scan Tool............................................................................................................ 11B – 24
Tech-2 Features ......................................................................................................... 11B – 25
Getting Started ......................................................................................................... 11B – 25
Operating Procedure................................................................................................. 11B – 26
Menu ..........................................................................................................................11B – 27
DTC ............................................................................................................................. 11B – 27
Clear DTC Information .............................................................................................. 11B – 27
Tech-2 Data Display................................................................................................... 11B – 27
Actuator Test ............................................................................................................. 11B – 27
Unlock / Lock Test..................................................................................................... 11B – 27
Arm / Disarm Signal Test ......................................................................................... 11B – 28
Horn Signal Test ........................................................................................................ 11B – 28
Turn Signal Test......................................................................................................... 11B – 28
Theft LED Test ........................................................................................................... 11B – 28
Programming............................................................................................................. 11B – 29
Erase remote keys..................................................................................................... 11B – 29
Program Remote Keys .............................................................................................. 11B – 30
ProgramAntitheft Waring......................................................................................... 11B – 31
Program Country Code ............................................................................................. 11B – 32
Program Vehicle Options.............................................................................................. 11B – 33
Tech-2 Data List ......................................................................................................... 11B – 34
DIAGNOSIS .................................................................................................................... 11B – 35
Diagnostic procedure................................................................................................ 11B – 35
Clearing Diagnostic Trouble Codes ......................................................................... 11B – 35
Verifying Vehicle Repair............................................................................................ 11B – 35
Diagnostic Aids ......................................................................................................... 11B – 35
Check the condition for system parts ..................................................................... 11B – 35
Check the Electro-Magnetic Interference (EMI) ..................................................... 11B – 35
Check the other items .............................................................................................. 11B – 35
Check the operation.................................................................................................. 11B – 35
Diagnostic Trouble Code (DTC) list.......................................................................... 11B – 36
Antitheft System Check ........................................................................................... 11B – 37
No Antitheft Lamp .................................................................................................... 11B – 38
DTC13 Security code not yet programmed ............................................................ 11B – 39
DTC14 No remote key programmed ....................................................................... 11B – 40
DTC16 Door lock actuators short circuit to ground ............................................... 11B – 41

ANTITHEFT SYSTEM 11B – 3
Service Precaution
WARNING:
THIS VEHICLE HAS A SUPPLEMENTAL RESTRAINT SYSTEM (SRS). REFER TO THE SRS COMPONENT AND
WIRING LOCATION VIEW IN ORDER TO DETERMINE WHETHER YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS WIRING. WHEN YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS WIRING, REFER TO THE SRS SERVICE INFORMATION.
FAILURE TO FOLLOW WARNINGS COULD RESULT IN POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION:
Always use the correct fastener in the proper location. When you replace a fastener, use ONLY the exact
part number for that application. ISUZU will call out those fasteners that require a replacement after
removal. ISUZU will also call out the fasteners that require thread lockers or thread sealant. UNLESS
OTHERWISE SPECIFIED, do not use supplemental coatings (Paints, greases, or other corrosion inhibitors)
on threaded fasteners or fastener joint interfaces. Generally, such coatings adversely affect the fastener
torque and the joint clamping force, and may damage the fastener. When you install fasteners, use the
correct tightening sequence and specifications. Following these instructions can help you avoid damage
to parts and systems.
DTC20 Broken wire to door lock actuators ............................................................ 11B – 42
DTC21 Remote key 1 with random code out of capture range ............................ 11B – 43
DTC22 Remote key 2 with random code out of capture range ............................ 11B – 44
DTC23 Remote key 3 with random code out of capture range ............................ 11B – 45
DTC24 Remote key 4 with random code out of capture range ............................ 11B – 46
DTC25 Remote key 5 with random code out of capture range ............................ 11B – 47
DTC28 Input immobiliser short circuit to ground .................................................. 11B – 48
DTC29 Broken wire to immobiliser ......................................................................... 11B – 49
DTC31 Actuator driver door defect ......................................................................... 11B – 50
DTC32 Actuator passenger door defect .................................................................. 11B – 51
DTC36 Broken wire to driver door........................................................................... 11B – 52
DTC37 Broken wire to passenger door ................................................................... 11B – 53
DTC41 Driver door micro switch unlock defect ..................................................... 11B – 54
DTC42 Driver door micro switch lock defect .......................................................... 11B – 55
DTC43 Driver door micro switch dead lock defect ................................................ 11B – 56
DTC44 Passenger door micro switch lock defect................................................... 11B – 57
DTC45 Passenger door micro switch unlock defect .............................................. 11B – 58
DTC47 Battery voltage for door lock actuators is missing ................................... 11B – 59
DTC50 A/D converter defect or battery voltage less than 9 volt ......................... 11B – 60
DTC51 E E P ROM defect .......................................................................................... 11B – 61
DTC52 E E P ROM not programmed by ISUZU ...................................................... 11B – 62
DTC55 Control unit defect ........................................................................................ 11B – 63
DTC123 Output flasher short circuit to grpund or broken wire ........................... 11B – 64
DTC125 Output alarm horn broken wire ................................................................ 11B – 65

11B – 8 ANTITHEFT SYSTEM
ANTI-THEFT INDICATER SIDE TURN SIGNAL , HAZARD
WARNING LIGHT ; RH
ANTI-THEFT HORN FRT TURN SIGNAL , HAZARD
WARNING LIGHT ; RH
ENGINE HOOD SWANTI-THEFT
CONTROLLERRR DOOR SW ; RH
FRT DOOR LOCKACTUATOR ; RHFRT DOOR KEY SW ; RHFRT DOOR SW ; RH
RR DOOR LOCK ACTUATOR ; RHFRT DOOR SW ; LH
RR DOOR LOCK ACTUATOR ; LH RR DOOR SW ; LH
FRT DOOR LOCKACTUATOR ; LHFRT DOOR KEY SW ; LH
SIDE TURN SIGNAL , HAZARD
WARNING LIGHT ; LH FRT TURN SIGNAL , HAZARD
WARNING LIGHT ; LHRELAY ; HAZARD
RR TURN SIGNAL , HAZARD
WARNING LIGHT ; LH
RAW4C0XF000201
COMPONENT WIRING LOCATORS (LHD)

ANTITHEFT SYSTEM 11B – 11
RTW48AXF025001
A
DOOR SW-DR
B-73
DOOR SW-PASSDOOR SW-RR RHDOOR SW-RR LH
L-7
0.5
B/W0.5
B/W0.5
B/W
0.5
R/G0.5
R/G0.5
R/G 0.5
R/G0.5
R/G
1
ALARMER C/U
(BUZZER)
1=with ALARMER C/U(BUZZER) only0.5
R/G0.5
R/G0.5
R/W
1.25
B
1.25
B
2.0
B
2.0
B
DOME
LIGHTHORN;
ANTI THEFT
L-91
H-72 L-9
2
RR DEF
(1)
WELD
SPLICE MAP
LIGHT
C-109
BODY-CTR
R-62
R-61
R-11
R-101
R-91 2
H-26L-11
L-1
2
H-1210
H-127R-1R-10R-9
0.5
R/B0.5
R/B
0.5
R/B0.5
R/B
2 2 2
9
H-2614
H-2613
H-26
C-11 10A
AUDIO
2 B-56 3
B-624 2
B-62 B-62
3 B-63
P-6P-5
8
BIG.1IG.2 MAIN
20
B/Y8
B/R
3
W/B
3
W3
W/B
3
B/Y
0.5
R/Y0.5
R/W0.5
R/W0.85R/Y
0.85
O/W
0.85O/W 1.25
LG/W 5
W
P-11
C-108 2
C-108
B1 B2
IG1 IG2 ACCOFF
ST
P-10P-2SBF-180A (4JA1/4JH1)
100A (6VE1/C24SE)
DOOR LOCKC-14
20A
ANTI THEFTC-17
10A
ROOM LAMPC-16
10A SBF-540A50A
SBF-9
BODY ENGINE
JANCTION BLOCK
B-56
8
B-43
2B-43
6
H-134
H-257
D-207
D-206H-104
H-247
D-103
D-104B-44
1B-44
2 4
B-445
B-442
C-117
5
H-12 9
B-43 3
B-43B-55
4B-56C-108
4
H-810 C-117
1 6
H-620
AUTO DOOR LOCK SW.
DRIVER SIDE
AUTO DOOR LOCK SW.
PASSENGER SIDE
0.5
LG/R
0.5
LG/R0.5
LG/R 0.5
R/L
0.5
R/L0.5
R/L
(POWER WINDOW SW.)
LOCK UN LOCK
WITH POWER WINDOW
DOOR LOCK
MOTORB ACC
ANTI THEFT C/U(with KEYLESS ENTRY) STARTER
SW.
3
L
POWER
SUPPLY
RTW48AXF025001
WIRING DIAGRAM (LHD)