2004 ISUZU TF SERIES ignition

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-19

5. Connect the Tech 2 SAE 16/19 adapter to the
vehicle DLC (1).






060r300015
6. The vehicle ignition turns on.
7. Verify the Tech 2 power up display.





060RW009
NOTE: The RS232 Loop back connector is only to use
for diagnosis of Tech 2 and refer to user guide of the
Tech 2.

8. The power up screen is displayed when you
power up the tester with the Isuzu systems
PCMCIA card. Follow the operating procedure
below.




060R100102

7A2-28 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

2.Demand of Data
1.
Connect Tech-2 to the vehicle. When activated by
turning on the power of Tech-2, push the "Enter"
switch.
2.
Turn on the ignition switch (without starting the
engine)
3.
In the main menu of Diagnostic Tester, push "F1:
Service Programming System (SPS)".
4.
Push "F0: Request Info" of Tech-2.

5.
Where vehicle data has been already saved in
Tech-2, the existing data come on display. In this
instance, as Tech-2 starts asking whether to keep
the data or to continue obtaining anew data from
the control unit, choose either of them.





6.
If you select “continue ”, you have to select “Model
Year ”, “Vehicle Type ”, “Controller Type (Engine) ”.
7.
After that. then push button and turn Ignition
switch tuned on, off, on following Tech-2 display.
Tech-2 will read information from controller afte
r
this procedure.
8.
During obtaining information, Tech-2 is receiving
information from the control unit chosen. In
replacing the control unit, please be sure to
undertake "Obtaining Information" from the new
unit. With VIN not being programmed into the new
control unit at the time of shipment, "obtaining
information" is not complete (because the vehicle
model, engine model and model year are specified
from VIN). For the procedure get additional
information on vehicles, instruction will be
provided in dialog form, when TIS2000 is in
operation.
9.
Following instructions by Tech-2, push the "Exit"
switch of Tech-2, turn off the ignition of the vehicle
and turn off the power of Tech-2, thereby
removing from the vehicle.

3.Data Exchange
1.
Connect Tech-2 to P/C, turn on the power and
click the "Next" button of P/C.
2.
Check VIN of the vehicle and choose "Next".
3.
When a lack of data is asked from among the
following menu, enter accordingly.
Select following Menu

Model Year

Model

Engine type

Transmission type

Destination code (vehicles for general
export)*1

Immobiliser
* 1: How to read the destination code
"Destination code can be read from ID Plate affixed on
vehicles, while on VIN plate the destination code is
described at the right-hand edge of Body Type line. In
Fig.-3, the destination code can be read as "EK4"
(Europe).

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-29





4.
After choosing the data, click the "Next" button.
5.
When all the necessary information is entered, the
"details" of software within the database that
match the entered data will appear fo
r
confirmation. Click the "Program" switch and then
download the new software onto Tech-2.
6. "Data Transfer" comes on display. The progress o
f
downloading will be displayed on the screen in the
form of bar graph.
7.
Upon finishing the data transfer, turn off the powe
r
of Tech-2, removing from P/C.


4. Programming of ECM 1.
Check to see if batteries are fully charged, while
ABS connectors shall be removed from the
vehicle.
2.
Connect Tech-2 to Vehicle Diagnostic Connectors.
3.
Turn on the power of Tech-2 and the title screen
comes on display.
4.
Turn on the ignition (without allowing the engine to
start)
5.
On the title screen of Tech-2, push the "Enter"
button.
6.
Choose "F: Service Programming System" on the
main screen and then choose "Fl: Programming".
7.
While data is being transferred, "Downloading"
will be displayed on the Tech-2 screen.
8.
Upon finishing the data transfer, Tech-2 will
display "Reprogramming Successful". Push the
"Exit" button to bring program to completion.

9.
Following "Procedure 2: Demand of Data", try ove
r
again "Information Obtaining" and check to
confirm if the data has been correctly re-loaded.
10. Upon finishing confirmation, turn off the ignition o
f
the vehicle and then turn off the power of Tech-2,
removing from the vehicle.

7A2-32 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

Clear DTC
NOTE: If you clear the DTC (Diagnostic Trouble
Codes) you will not be able to read any codes recorded
during the last occurrence.
NOTE: To use the DTC again to identify a problem,
you will need to reproduce the fault or the problem.
This may require a new test drive or just turning the
ignition on (this depends on the nature of the fault).
1. IF you have a Tech 2:
1. Connect the Tech 2 if it is still not connected go
through Tech 2 OBD CONNECTION.
2. Push “F1: Clear DTC Information" in the
Application Menu and answer “Yes" to the
question “Do you want to clear DTC's?"
a. When a malfunction still exists and the Tech 2 displays “AW30-40 CODES NOT
CLEARED". This means that the problem is
still there or that the recovery was not done.
Please go to DTC CHECK.
b. When a malfunction has been repaired and the recovery is done the Tech 2 displays
“ AW30-40LE CODES CLEARED".
2. When you have no Tech 2, the storaged trouble
codes can be cleared by shorting the terminals
No.11 and No.4 or 5 (ground) of data link connecto
r
with a lead wire for 1  6 seconds.
DTC Check
1. Diagnostic Trouble Codes (DTC) have been
identified by Tech 2.
2. You have written the list of the DTCs. The order o
f
the malfunctions has no meanings for this TCM.
Usually only one or two malfunctions should be set
for a given problem.
3. Check directly the DTCs you identified. The DTCs
are sorted by number. Refer to Diagnostic Trouble
Code (DTC) Identification in this section.
TCM Precaution
The TCM can be damaged by:
1. The electrostatic discharge
2. The short circuit of some terminals to voltage or to
ground.
Electrostatic Discharge Damage Description: 1. Electronic components used to control systems are often designed to carry very low voltage, and
are very susceptible to damage caused by
electrostatic discharge. It is possible for less than
100 volts of static electricity to cause damage to
some electronic components. By comparison, it
takes as much as 4,000 volts for a person to even
feel the zap of a static discharge.
2. There are several ways for a person to become
statically charged. The most common methods o
f
charging are by friction and induction. An example
of charging by friction is a person sliding across a
car seat, in which a charge of as much as 25,000
volts can build up. Charging by induction occurs
when a person with well insulated shoes stands
near a highly charged object and momentarily
touches ground. Charges for the same polarity are
drained off, leaving the person highly charged with
the opposite polarity. Static charges of either type
can cause damage, therefore, it is important to
use care when handling and testing electronic
components.
NOTE: To prevent possible electrostatic discharge
damage:
1. Do not touch the TCM connector pins or soldered
components on the TCM circuit board.
2. Be sure to follow the guidelines listed below i
f
servicing any of these electronic components:
3. Do not open the replacement part package until it is time to install the part.
4. Avoid touching electrical terminals of the part.
5. Before removing the part from its package, ground
the package to a known good ground on the
vehicle.
6.
Always touch a known good ground before handling
the part. This step should be repeated before
installing the part if the part has been handled
while sliding across the seat, while sitting down
from a standing position or while walking some
distance.
Information On TCM
1. The Transmission Control Module (TCM) is located
in the place of a clutch pedal and is the control
center of the electronic transmission control
system.
2. The TCM must be maintained at a temperature below 85

C (185

F) at all times. This is most
essential if the vehicle is put through a paint baking
process. The TCM will become inoperative if its
temperature exceeds 85

C (185

F). Therefore, it is
recommended that the TCM be removed or that
temporary insulation be placed around the TCM
during the time the vehicle is in a paint oven o
r
other high temperature process.
3. The TCM is designed to process the various inputs and then respond by sending the appropriate
electrical signals to control transmission upshift,
downshift, shift feel and torque converter clutch
engagement.
4. The TCM constantly interprets information from the
various sensors, and controls the systems that
affect transmission and vehicle performance. By
analyzing operational problems, the TCM is able to

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-35

DTC P0560 (FLASHING CODE 25) System Voltage Error



RTW37ALF000701
Circuit Description
The Transmission Control Module (TCM) monitors the
system voltage on the ignition feed terminal to the
TCM. A system voltage DTC will set whenever the
voltage is below or above a calibrated value.
Condition for setting the DTC
When the TCM detects following conditions.

Ignition voltage is less than 9V or more than 18V.
 Engine speed is more than 600 rpm.
Action Taken When The DTC Sets

DTC stored.

Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.

The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.

7A2-36 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.
DTC P0560 – System Voltage Error
Step Action Value(s) YES NO
1
Was the powertrain On-Board Diagnostic (OBD)
System Check performed? — Go to Step 2 Go to OBD
System Check
2 Using a DVM, measure the battery voltage at the
battery.
Is the battery voltage greater than the specified
value? 11.5 V Go to Step 3 Charge battery,
then go to Step
3
3

1. Install a Tech 2.

2. Select “Ignition Volts" on the Tech 2.
3. Start the engine and raise the engine speed to the
specified value.

4. Load the electrical system by turning on the
headlights, high blower, etc.
Is the ignition voltage approximately equal to the
specified value? 2000 RPM
12.8-14.1 VGo to Step 4 Go to
Starting/Chargi
ng
4

1. Ignition “OFF".

2. Disconnect the TCM connector at the TCM.

3. Using a DVM, measure the battery voltage at the
TCM connector C-94.
Is it approximately equal to battery voltage? — Check for
excessive
curren draw
with ignition
“OFF" engine
“OFF". Go to Step 5
5

1. Check for faulty connections at the TCM harness
terminals.

2. Repair as necessary.
Was a repair necessary? — Verify repair Go to Step 6
6 Check for an open battery feed circuit to the TCM.
Is the action complete? — Verify repair Go to Step 7
7 Replace the TCM.
Important:
The replacement TCM must be
programmed. (Refer to SPS for procedure.)
Is the action complete? — Verify repair —

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-37

DTC P0602 (FLASHING CODE 63) Transmission Control Module (TCM)
Programming Error
Circuit Description
The Service Programming System (SPS) updates the
flash calibration files that are stored in a Transmission
Control Module (TCM). The calibration file
custom-tailors a module to a certain vehicle. The
calibration file contains data for things such as spark
curves and fuel control. When troubleshooting a
driveability problem, diagnosis may call fo
r
reprogramming the controller with newer calibration
information to correct a customer concern and Vehicle
Identification Number (VIN).
Condition for setting the DTC
When the TCM is not written VIN No.
Action Taken When The DTC Sets

DTC stored.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.
Diagnostic Aids
DTC P0602 is indicated when the TCM does not written
VIN No. A security lock is performed by SPS. And not
replace the TCM when DTC P0602 can repair by SPS.

7A2-40 TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)

Condition 2 ("Short"):
When the TCM detects 2 times or more signals o
f
range sensor more than 0.025 sec at following
conditions.

Vehicle speed is more than 19 mph.
 Engine speed is more than 1500 rpm.
Action Taken When The DTC Sets

No 3rd start mode.
 No slope control.

The TCM judges always D range position of range
sensor at "Condition 1".

The TCM judges the position of range sensor with
following priority at "Condition 2".

There is a priority in order of D, 3, 2, L, R, N, and P.

Check Trans ON.

DTC stored.
Conditions For Clearing The DTC

The DTC can be cleared from the TCM history by
using a scan tool.
 The DTC will be cleared from history when the
vehicle has achieved 40 warm-up cycles without a
failure reported.

After more than 1 second has elapsed after the
ignition key has been turned “ON", short between
No.11 and No.4 (ground) of DLC (Data Link
Connector). Then, after 1 second, but within 6
seconds, discontinue shorting.

Diagnostic Aids

Inspect the wiring for poor electrical connection at
the TCM. Look for possible bent, backed out,
deformed or damaged terminals. Check for weak
terminal tension as well. Also check for a chafed wire
that could short to bare metal or other wiring.
Inspect for a broken wire inside the insulation.

When diagnosing for a possible intermittent short o
r
open condition, move the wiring harness while
observing test equipment for a change.
 Check range sensor for proper mounting and
adjustment.