2004 ISUZU TF SERIES length

UNIT REPAIR (JR405E) 7A4-47
Free length – 36.4 mm (1.433 in)
Linear diameter – 1.2 mm (0.047 in)


21C&L-SUB31

Reassembly steps
Coat the parts with ATF before installing them.
1. Bearing
Install the bearing into the low clutch drum.


22C&L-SUB30

2. Snap ring
Install the snap ring to the low clutch drum.


23C&L-SUB28

3. Low one-way clutch
Install the low one-way clutch to the low clutch drum.


24C&L-SUB33

NOTE:
The flanged side of the low one-way clutch must face the
outside.

UNIT REPAIR (JR405E) 7A4-57

11CASE-AY01

5. Oil seal
Using a screwdriver, remove the oil seal from the
transmission case.




Inspection
2 – 4 brake drive plate
Measure the 2-4 brake drive plate facing thickness at 3
points and calculate the average value.
If the average value is less than the specified limit, the 2-4
brake drive plate must be replaced.
2 – 4 brake drive plate facing thickness:
Standard = 2.0 mm (0.079 in)
Limit = 1.8 mm (0.071 in)
Low and reverse brake drive plate
Measure the low and reverse brake drive plate facing
thickness at 3 points and calculate the average value.
If the average value is less than the specified limit, the lo
w
and reverse drive plate must be replaced.
Low and reverse brake drive plate facing thickness:
Standard = 2.0 mm (0.079 in)
Limit = 1.8 mm (0.071 in)
2 – 4 brake return spring

Check the number of effective 2-4 brake return spring
coils.
Effective return spring coils (Standard): 10.2

Measure the 2-4 brake return spring outside diameter,
free length, and linear diameter.
If any of the measured values exceed the specified limit,
the 2-4 brake return spring must be replaced.
2 – 4 brake return spring measurements (Standard):
Outside diameter = 6.9 mm (0.272 in)
Free length = 22.5 mm (0.886 in)
Linear diameter = 1.1 mm (0.043 in)
Low and reverse brake return spring

Check the number of effective low and reverse brake
return spring coils.
Effective return spring coils (standard): 4.8

Measure the low and reverse brake return spring outside
diameter, free length, and linear diameter.
If any of the measured values exceed the specified limit,
the low and reverse return spring must be replaced.
Low and reverse brake return spring measurements
(Standard):
Outside diameter = 11.2 mm (0.441 in)

7A4-58 UNIT REPAIR (JR405E)
Free length = 22.3 mm (0.878 in)
Linear diameter = 1.1 mm (0.043 in)


12CASE-AY06

Reassembly steps
1. Oil seal, manual shaft, and manual plate

Use the oil seal installer to force the manual plate oil
seal into place.
Oil seal installer: 5-8840-2758-0


14CASE-AY21



Install the manual shaft together with the manual plate.


15CASE-AY26



Drive the spring pin into the transmission case.


16CASE-AY37

2. Parking rod

Rotate the manual plate while installing the parking rod.

UNIT REPAIR (JR405E) 7A4-81

43ASSY119

20.Control valve assembly


Align the manual valve and the manual plate of the
transmission case.











Install the control valve assembly and tighten the 12
fixing bolts to the specified torque.
Number of bolts Length Color
10 (A) 40 mm (1.57 in) Gold
2 (B) 30 mm (1.18 in) Gold

44ASSY121


Torque: 8 N 


m (69 Ib 


in)



45CV29



Connect the harness assembly and control valve
assembly connectors.

7A4-84 UNIT REPAIR (JR405E)

SERVICE STANDARD
Name BESCO ATF II or ATF III ATF
Quantity L 9.2 – 9.6
Seal ring clearance mm (in) 0.10 – 0.25 (0.0039 – 0.0098)
Housing and inner rotor side clearance mm (in) 0.02 – 0.04 (0.0008 – 0.0016)
Oil pump
Outer rotor and crescent clearance mm (in) 0.02 – 0.15 (0.0008 – 0.0059)
Number of drive plate / driven plate 7/7
Standard mm (in) 2.0 (0.079)Drive plate facing thickness
Limit mm (in) 1.8 (0.071)
Retaining plate and snap ring clearance mm (in) 0.9 – 1.3 (0.035 – 0.051)
3.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)
Available low clutch retaining plate thickness mm (in)
4.8 (0.189)
Number of coil 9.9
Outside diameter mm (in) 9.7 (0.382)
Free length mm (in) 36.4 (1.433)
Low clutch
Return spring
Linear diameter mm (in) 1.2 (0.047)
Number of drive plate / driven plate 5/5
Standard mm (in) 2.0 (0.079)Drive plate facing thickness
Limit mm (in) 1.8 (0.071)
Retaining plate and snap ring clearance mm (in) 1.2 – 1.6 (0.047 – 0.063)
4.6 (0.181)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205)
Available high clutch retaining plate thickness mm (in)
5.4 (0.213)
Number of coil 10.2
Outside diameter mm (in) 8.0 (0.315)
Free length mm (in) 27.1 (1.067)
High clutch
Return spring
Linear diameter mm (in) 1.1 (0.043)
Number of drive plate / driven plate 2/2
Standard mm (in) 2.0 (0.079)Drive plate facing thickness
Limit mm (in) 1.8 (0.071)
Retaining plate and snap ring clearance mm (in) 0.6 – 0.9 (0.0236 – 0.035)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205)
Reverse clutch
Available reverse clutch retaining plate thickness mm (in)
5.4 (0.213)
Low one-way
clutch Seal ring clearance mm (in) 0.10 – 0.25 (0.0039 – 0.0098)
Number of drive plate / driven plate 6/6
Standard mm (in) 2.0 (0.079)Drive plate facing thickness
Limit mm (in) 1.8 (0.071)
Retaining plate and snap ring clearance mm (in) 0.7 – 1.1 (0.028 – 0.043)
5.2 (0.205)
5.4 (0.213)
5.6 (0.220)
5.8 (0.228)
Low & reverse
brake
Available low & reverse brake retaining plate
thickness mm (in)
6.0 (0.236)

UNIT REPAIR (JR405E) 7A4-85

SERVICE STANDARD (Cont’d)
Number of coil 4.8
Outside diameter mm (in) 11.2 (0.441)
Free length mm (in) 22.3 (0.878)
Return spring
Linear diameter mm (in) 1.1 (0.043)
Number of drive / driven plate 5/5
Standard mm (in) 2.0 (0.079)Drive plate facing thickness
Limit mm (in) 1.8 (0.071)
Retaining plate and retaining plate clearance mm (in) 1.0 – 1.4 (0.039 – 0.055)
5.4 (0.213)
5.6 (0.220)
5.8 (0.228)
6.0 (0.236)
6.2 (0.244)
Available 2-4 brake retaining plate thickness mm (in)
6.4 (0.252)
Number of coil 10.2
Outside diameter mm (in) 6.9 (0.272)
Free length mm (in) 22.5 (0.886)
2-4 brake
Return spring
Linear diameter mm (in) 1.1 (0.043)
Output shaft Seal ring clearance mm (in) 0.10 – 0.25 (0.0039 – 0.0098)
Total end play mm (in) 0.25 – 0.55 (0.0098 – 0.0217)
1.4 (0.055)
1.6 (0.063)
1.8 (0.071)
2.0 (0.079)
2.2 (0.087)
Total end play
Available oil pump bearing race thickness mm (in)
2.4 (0.094)
Torque converter end play mm (in) 67.0 (2.638)