2004 INFINITI QX56 battery

AT-222
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
2. CHECK 4TH POSITION SWITCH CIRCUIT
With CONSULT-II
1. Turn ignition switch “ON”.
2. Select "ECU INPUT SIGNALS" in "DATA MONITOR" mode for
"A/T" with CONSULT-II.
3. Read out "OD CONT SW" switch moving selector lever to each
position.
Without CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine)
2. Check voltage between A/T device harness connector terminal
and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. CHECK A/T FLUID LEVEL
Check the A/T fluid level again. Refer to AT- 1 3 , "
Checking A/T Fluid"
.
OK or NG
OK >> GO TO 4.
NG >> Refill ATF.
Monitor item Condition Display value
OD CONT SWWhen setting the selector
lever to "4" and "3" posi-
tion.ON
When setting selector
lever to other positions.OFF
LCIA0339E
Item Connector No.Te r m i n a l N o .
(Wire color)ConditionData
(Approx.)
4th position
switchM2031 (SB) -
GroundWhen setting
the selector
lever to "4"
and "3" posi-
tion.0V
When setting
selector lever
to other posi-
tions.Battery volt-
age
LCIA0340E
SAT6 3 8A

AT-228
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
2. CHECK 1ST POSITION SWITCH CIRCUIT
With CONSULT-II
1. Turn ignition switch “ON”.
2. Select "ECU INPUT SIGNALS" in "DATA MONITOR" mode for
"A/T" with CONSULT-II.
3. Read out "1 POSITION SW" switch moving selector lever to
each position.
Without CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine)
2. Check voltage between A/T device harness connector terminal
and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
3. CHECK A/T FLUID LEVEL
Check the A/T fluid level again. Refer to AT- 1 3 , "
Checking A/T Fluid"
.
OK or NG
OK >> GO TO 4.
NG >> Refill ATF.
Monitor item Condition Display value
1 POSITION SWWhen setting the selector
lever to "1" position.ON
When setting selector
lever to other positions.OFF
LCIA0339E
Item Connector No.Te r m i n a l N o .
(Wire color)ConditionData
(Approx.)
1st position
switchM2037 (Y/G) -
GroundWhen setting
the selector
lever to "1"
position.0V
When setting
selector lever
to other posi-
tions.Battery volt-
age
LCIA0341E
SAT6 3 8A

AT-230
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
9. DETECT MALFUNCTIONING ITEM

Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-68,
"Symptom Chart" (Symptom No.17).
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
Vehicle Does Not Decelerate By Engine BrakeUCS002J 2
SYMPTOM:
No engine brake is applied when the gear is shifted from the 22 to 11 .
DIAGNOSTIC PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Perform self-diagnosis.
Do the self-diagnosis results indicate PNP switch, ATF pressure switch 5?
YES >> Check the malfunctioning system. Refer to AT-109, "DTC P0705 PARK/NEUTRAL POSITION
SWITCH" , AT-181, "DTC P1845 ATF PRESSURE SWITCH 5" .
NO >> GO TO 2.
2. CHECK 1ST POSITION SWITCH CIRCUIT
With CONSULT-II
1. Turn ignition switch “ON”.
2. Select "ECU INPUT SIGNALS" in "DATA MONITOR" mode for
"A/T" with CONSULT-II.
3. Read out "OVERDRIVE SW" switch moving selector lever to
each position.
Without CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine)
2. Check voltage between A/T device harness connector terminal
and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
Monitor item Condition Display value
1 POSITION SWWhen setting the selector
lever to "1" position.ON
When setting selector
lever to other positions.OFF
LCIA0339E
Item Connector No.Te r m i n a l N o .
(Wire color)ConditionData
(Approx.)
1st position
switchM2037 (Y/G) -
GroundWhen setting
the selector
lever to "1"
position.0V
When setting
selector lever
to other posi-
tions.Battery volt-
age
LCIA0341E

AT-238
A/T SHIFT LOCK SYSTEM
Revision: August 20072004 QX56
Shift Lock Control Unit Reference ValuesUCS002J 9
SHIFT LOCK HARNESS CONNECTOR TERMINALS LAYOUT
SHIFT LOCK CONTROL UNIT INSPECTION TABLE
Data are reference values.
NOTE:
Confirm that the pointer swings only momentarily because the output time is so short. If the inspection is done with an oscilloscope, it
should be observed that the power source voltage lasts for 3.5 to 10 ms.
LCIA0327E
TER-
MINAL
NO.WIRE
COLORITEM CONDITIONVOLTAGE
(V)
1 Y/R Power sourceIgnition switch: “ON” Battery voltage
Ignition switch: “OFF” Battery voltage
2L/R Detention switch
(for key)When selector lever is not in "P" position with key inserted. Battery voltage
Except the above Approx. 0V
3GRDetention switch
(for shift)When selector lever is not in "P" position Battery voltage
Except the above Approx. 0V
4 R/G Stop lamp switchWhen brake pedal is depressed Battery voltage
When brake pedal is released Approx. 0V
5W/RVehicle speed sig-
nal——
——
6 G/R Ignition signalIgnition switch: “OFF” Approx. 0V
Ignition switch: “ON” Battery voltage
7 R/W Shift lock solenoidWhen brake pedal is depressed with ignition switch "ON". Approx. 0V
When brake pedal is depressed. Battery voltage
8 B Ground — Approx. 0V
9 G/W Key lock solenoidWhen the selector lever is set to a position other than the “P”
position, and the key switch is turned from “ON” to “OFF”Battery voltage for
approx. 0.1 sec.
(Note)
Except the above Approx. 0V
10 W/G Key unlock solenoidWhen ignition switch is not in "ON” position with key inserted.Battery voltage for
approx. 0.1 sec.
(Note)
Except the above Approx. 0V

A/T SHIFT LOCK SYSTEM
AT-239
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
Component InspectionUCS002J A
SHIFT LOCK SOLENOID

Check operation by applying battery voltage to the A/T device.
CAUTION:
Be sure to apply the voltage of the correct polarity to the
respective terminals. Otherwise, the part may be damaged.
DETENTION SWITCH
For key:

Check continuity between terminals of the A/T device.
DETENTION SWITCH
For shift:

Check continuity between terminals of the A/T device.
KEY LOCK SOLENOID
Key lock

Check operation by applying battery voltage to key switch and
key lock solenoid.
CAUTION:
Be careful not to cause burnout of the harness.
Connector No. Terminal No.
M203 9 (Battery voltage) - 10 (Ground)
LCIA0328E
ConditionConnector
No.Terminal No. Continuity
When selector lever is “P”
position.
M203 5 - 6No
When selector lever is not “P”
position.Ye s
LIIA1599E
ConditionConnector
No.Terminal No. Continuity
When selector lever is “P”
position.
M203 3 - 4No
When selector lever is not “P”
position.Ye s
WCIA0401E
Connector No. Terminal No. (Wire color)
M27 1 (Battery voltage) - 2 (Ground)
WCIA0240E

AT-240
A/T SHIFT LOCK SYSTEM
Revision: August 20072004 QX56
Key unlock

Check operation by applying battery voltage to key switch and
key lock solenoid.
CAUTION:
Be careful not to cause burnout of the harness.
KEY SWITCH

Check continuity between terminals of the key switch and key
lock solenoid.
STOP LAMP SWITCH

Check continuity between terminals of the stop lamp switch.
Check stop lamp switch after adjusting brake pedal.
Connector No. Terminal No. (Wire color)
M27 2 (Battery voltage) - 1 (Ground)
WCIA0241E
Condition Connector No.Te r m i n a l N o .
(Wire color)Continuity
Key inserted
M27 3 - 4Ye s
Key withdrawn No
WCIA0242E
ConditionConnector
No.Te r m i n a l N o .
(Wire color)Continuity
When brake pedal is depressed
E38 3 - 4Ye s
When brake pedal is released No
SCIA2126E

AT-242
ON-VEHICLE SERVICE
Revision: August 20072004 QX56
CONTROL VALVE WITH TCM REMOVAL AND INSTALLATION
Removal
1. Disconnect negative battery terminal
2. Drain ATF through drain plug.
3. Disconnect A/T assembly harness connector.
4. Remove snap ring from A/T assembly harness connector.
5. Push A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
6. Remove oil pan and oil pan gasket.
7. Check foreign materials in oil pan to help determine causes of
malfunction. If the A/T fluid is very dark, smells burned, or con-
tains foreign particles, frictional material (clutches, band) may
need replacement. A tacky film that will not wipe clean indicates
varnish build up. Varnish can cause valves, servo, and clutches
to stick and can inhibit pump pressure.

If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to AT- 1 5 , "
A/T Fluid Cooler Cleaning" .
SCIA5021E
SCIA5022E
SCIA2308E
SCIA5199E

AT-248
ON-VEHICLE SERVICE
Revision: August 20072004 QX56
b. Install oil pan (with oil pan gasket) to transmission case.
CAUTION:

Install it so that drain plug comes to the position as
shown in the figure.

Be careful not to pinch harnesses.

Complete remove all moisture, oil and old gasket, etc.
From oil pan mounting surfaces.
c. Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to AT-241, "
COMPONENTS" .
CAUTION:
Do not reuse oil pan mounting bolts.
14. Install drain plug to oil pan. Tighten drain plug to the specified
torque. Refer to AT-241, "
COMPONENTS" .
CAUTION:
Do not reuse drain plug gasket.
15. Pull up A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
16. Install snap ring to A/T assembly harness connector.
17. Connect A/T assembly harness connector.
18. Pour ATF into transmission assembly. Refer to AT - 1 3 , "
Chang-
ing A/T Fluid" .
19. Connect the negative battery terminal
SCIA2308E
SCIA2492E
SCIA5038E
SCIA5039E