2004 INFINITI QX56 brake light

EC-8Revision: August 2007
INDEX FOR DTC
2004 QX56
INDEX FOR DTCPFP:00024
Alphabetical IndexUBS00GZ3
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-135, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
×:Applicable —: Not applicable
Items
(CONSULT-II screen terms)DTC*
1
TripMIL lighting
upReference page
CONSULT-II
GST*
2ECM*3
A/F SEN1 (B1) P1271 1271 2×EC-429
A/F SEN1 (B1) P1272 1272 2×EC-437
A/F SEN1 (B1) P1273 1273 2×EC-445
A/F SEN1 (B1) P1274 1274 2×EC-454
A/F SEN1 (B1) P1276 1276 2×EC-463
A/F SEN1 (B1) P1278 1278 2×EC-472
A/F SEN1 (B1) P1279 1279 2×EC-484
A/F SEN1 (B2) P1281 1281 2×EC-429
A/F SEN1 (B2) P1282 1282 2×EC-437
A/F SEN1 (B2) P1283 1283 2×EC-445
A/F SEN1 (B2) P1284 1284 2×EC-454
A/F SEN1 (B2) P1286 1286 2×EC-463
A/F SEN1 (B2) P1288 1288 2×EC-472
A/F SEN1 (B2) P1289 1289 2×EC-484
A/F SEN1 HTR (B1) P1031 1031 2×EC-354
A/F SEN1 HTR (B1) P1032 1032 2×EC-354
A/F SEN1 HTR (B2) P1051 1051 2×EC-354
A/F SEN1 HTR (B2) P1052 1052 2×EC-354
ACC COMMAND VALUE*7P1568 1568 1 —EC-524
A/T INTERLOCK P1730 1730 1×AT-139
A/T TCC S/V FNCTN P0744 0744 2×AT-121
APP SEN 1/CIRC P2122 2122 1×EC-556
APP SEN 1/CIRC P2123 2123 1×EC-556
APP SEN 2/CIRC P2127 2127 1×EC-562
APP SEN 2/CIRC P2128 2128 1×EC-562
APP SENSOR P2138 2138 1×EC-576
ASCD BRAKE SW P1572 1572 1 —EC-525, EC-534
ASCD SW P1564 1564 1 —EC-510, EC-517
ASCD VHL SPD SEN*6P1574 1574 1 —EC-542, EC-544
ATF TEMP SEN/CIRC P0710 0710 2×AT-131
BRAKE SW/CIRCUIT P1805 1805 2 —EC-551
CAN COMM CIRCUIT U1000
1000*41×EC-135
CAN COMM CIRCUIT U1001
1001*42—EC-135
CKP SEN/CIRCUIT P0335 0335 2×EC-255
CLOSED LOOP-B1 P1148 1148 1×EC-407
CLOSED LOOP-B2 P1168 1168 1×EC-407

EC-14Revision: August 2007
INDEX FOR DTC
2004 QX56
P1052 1052 A/F SEN1 HTR (B2) 2×EC-354
P1065 1065 ECM BACK UP/CIRCUIT 2×EC-361
P1121 1121 ETC ACTR 1×EC-365
P1122 1122 ETC FUNCTION/CIRC 1×EC-367
P1124 1124 ETC MOT PWR 1×EC-373
P1126 1126 ETC MOT PWR 1×EC-373
P1128 1128 ETC MOT 1×EC-378
P1146 1146 HO2S2 (B1) 2×EC-383
P1147 1147 HO2S2 (B1) 2×EC-395
P1148 1148 CLOSED LOOP-B1 1×EC-407
P1166 1166 HO2S2 (B2) 2×EC-383
P1167 1167 HO2S2 (B2) 2×EC-395
P1168 1168 CLOSED LOOP-B2 1×EC-407
P1211 1211 TCS C/U FUNCTN 2 —EC-408
P1212 1212 TCS/CIRC 2 —EC-409
P1217 1217 ENG OVER TEMP 1×EC-410
P1225 1225 CTP LEARNING 2 —EC-420
P1226 1226 CTP LEARNING 2 —EC-422
P1229 1229 SENSOR POWER/CIRC 1×EC-424
P1271 1271 A/F SENSOR (B1) 2×EC-429
P1272 1272 A/F SENSOR (B1) 2×EC-437
P1273 1273 A/F SENSOR (B1) 2×EC-445
P1274 1274 A/F SENSOR (B1) 2×EC-454
P1276 1276 A/F SENSOR (B1) 2×EC-463
P1278 1278 A/F SENSOR (B1) 2×EC-472
P1279 1279 A/F SENSOR (B1) 2×EC-484
P1281 1281 A/F SENSOR (B2) 2×EC-429
P1282 1282 A/F SENSOR (B2) 2×EC-437
P1283 1283 A/F SENSOR (B2) 2×EC-445
P1284 1284 A/F SENSOR (B2) 2×EC-454
P1286 1286 A/F SENSOR (B2) 2×EC-463
P1288 1288 A/F SENSOR (B2) 2×EC-472
P1289 1289 A/F SENSOR (B2) 2×EC-484
P1444 1444 PURG VOLUME CONT/V 2×EC-496
P1446 1446 VENT CONTROL VALVE 2×EC-504
P1564 1564 ASCD SW 1 —EC-510, EC-517
P1568 1568
ACC COMMAND VALUE*71—EC-524
P1572 1572 ASCD BRAKE SW 1 —EC-525, EC-544
P1574 1574
ASCD VHL SPD SEN*61—EC-542, EC-517
P1610 - P1615 1610 - 1615 NATS MALFUNCTION 2 —BL-138
P1706 1706 P-N POS SW/CIRCUIT 2×EC-546
P1716 1716 TURBINE REV S/CIRC 2×AT-134
DTC*1
Items
(CONSULT-II screen terms)TripMIL lighting
upReference page
CONSULT-II
GST*
2ECM*3

INDEX FOR DTC
EC-15
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: August 20072004 QX56
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results). This number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-II.
*5: When the fail-safe operations for both self-diagnoses occur at the same time, the MIL illuminates.
*6: 2WD models
*7: Models with ICC systemP1730 1730 A/T INTERLOCK 1×AT- 1 3 9
P1752 1752 I/C SOLENOID/CIRC 1×AT- 1 4 5
P1754 1754 I/C SOLENOID FNCTN 1×AT- 1 4 8
P1757 1757 FR/B SOLENOID/CIRC 1×AT- 1 5 1
P1759 1759 FR/B SOLENOID FNCT 1×AT- 1 5 4
P1762 1762 D/C SOLENOID/CIRC 1×AT- 1 5 7
P1764 1764 D/C SOLENOID FNCTN 1×AT- 1 6 0
P1767 1767 HLR/C SOL/CIRC 1×AT- 1 6 3
P1769 1769 HLR/C SOL FNCTN 1×AT- 1 6 6
P1772 1772 LC/B SOLENOID/CIRC 1×AT- 1 6 9
P1774 1774 LC/B SOLENOID FNCT 1×AT- 1 7 2
P1805 1805 BRAKE SW/CIRCUIT 2 —EC-551
P2122 2122 APP SEN 1/CIRC 1×EC-556
P2123 2123 APP SEN 1/CIRC 1×EC-556
P2127 2127 APP SEN 2/CIRC 1×EC-562
P2128 2128 APP SEN 2/CIRC 1×EC-562
P2135 2135 TP SENSOR 1×EC-569
P2138 2138 APP SENSOR 1×EC-576
DTC*1
Items
(CONSULT-II screen terms)TripMIL lighting
upReference page
CONSULT-II
GST*
2ECM*3

BASIC SERVICE PROCEDURE
EC-45
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: August 20072004 QX56
On vehicles equipped with daytime light systems, if the parking brake is applied before the engine
is started, the headlamp will not be illuminated.

Steering wheel: Neutral (Straight-ahead position)

Vehicle speed: Stopped

Transmission: Warmed-up
For models with CONSULT-II, drive vehicle until “FLUID TEMP SE” in “DATA MONITOR” mode of “A/T”
system indicates less than 0.9V.
For models without CONSULT-II, drive vehicle for 10 minutes.
OPERATION PROCEDURE
With CONSULT-II
1. Perform EC-44, "Accelerator Pedal Released Position Learning" .
2. Perform EC-44, "
Throttle Valve Closed Position Learning" .
3. Start engine and warm it up to normal operating temperature.
4. Check that all items listed under the topic PREPARATION (previously mentioned) are in good order.
5. Select “IDLE AIR VOL LEARN” in “WORK SUPPORT” mode.
6. Touch “START” and wait 20 seconds.
7. Make sure that “CMPLT” is displayed on CONSULT-II screen. If
“CMPLT” is not displayed, Idle Air Volume Learning will not be
carried out successfully. In this case, find the cause of the inci-
dent by referring to the Diagnostic Procedure below.
8. Rev up the engine two or three times and make sure that idle
speed and ignition timing are within the specifications.
Without CONSULT-II
NOTE:

It is better to count the time accurately with a clock.

It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit
has a malfunction.
1. Perform EC-44, "
Accelerator Pedal Released Position Learning" .
SEF 2 17 Z
SEF 4 54 Y
ITEM SPECIFICATION
Idle speed 650±50 rpm (in P or N position)
Ignition timing 15±5° BTDC (in P or N position)
MBIB0238E

ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-53
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: August 20072004 QX56
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results). This number is controlled by NISSAN.
*4: When the fail-safe operations for both self-diagnoses occur at the same time, the MIL illuminates.
*5: The trouble shooting for this DTC needs CONSULT-II.
*6: SRT code will not be set if the self-diagnostic result is NG.
*7: 2WD models
*8: Models with ICC system
DTC AND 1ST TRIP DTC
The 1st trip DTC (whose number is the same as the DTC number) is displayed for the latest self-diagnostic
result obtained. If the ECM memory was cleared previously, and the 1st trip DTC did not reoccur, the 1st trip
DTC will not be displayed.
If a malfunction is detected during the 1st trip, the 1st trip DTC is stored in the ECM memory. The MIL will not
light up (two trip detection logic). If the same malfunction is not detected in the 2nd trip (meeting the required
driving pattern), the 1st trip DTC is cleared from the ECM memory. If the same malfunction is detected in the
2nd trip, both the 1st trip DTC and DTC are stored in the ECM memory and the MIL lights up. In other words,
the DTC is stored in the ECM memory and the MIL lights up when the same malfunction occurs in two consec-
utive trips. If a 1st trip DTC is stored and a non-diagnostic operation is performed between the 1st and 2nd
trips, only the 1st trip DTC will continue to be stored. For malfunctions that blink or light up the MIL during the
1st trip, the DTC and 1st trip DTC are stored in the ECM memory.
Procedures for clearing the DTC and the 1st trip DTC from the ECM memory are described in EC-62, "
HOW
TO ERASE EMISSION-RELATED DIAGNOSTIC INFORMATION" .
For malfunctions in which 1st trip DTCs are displayed, refer to EC-50, "
EMISSION-RELATED DIAGNOSTIC
INFORMATION ITEMS" . These items are required by legal regulations to continuously monitor the system/
component. In addition, the items monitored non-continuously are also displayed on CONSULT-II.
NATS MALFUNCTIONP1610 -
P16151610 - 1615 — —×BL-138
P-N POS SW/CIRCUIT P1706 1706 — —×EC-546
TURBINE REV S/CIRC P1716 1716 — —×AT- 1 3 4
A/T INTERLOCK P1730 1730 — — —AT- 1 3 9
I/C SOLENOID/CIRC P1752 1752 — — —AT- 1 4 5
I/C SOLENOID FNCTN P1754 1754 — — —AT- 1 4 8
FR/B SOLENOID/CIRC P1757 1757 — — —AT- 1 5 1
FR/B SOLENOID/CIRC P1759 1759 — — —AT- 1 5 4
D/C SOLENOID/CIRC P1762 1762 — — —AT- 1 5 7
D/C SOLENOID FNCTN P1764 1764 — — —AT- 1 6 0
HLR/C SOL/CIRC P1767 1767 — — —AT- 1 6 3
HLR/C SOL FNCTN P1769 1769 — — —AT- 1 6 6
LC/B SOLENOID/CIRC P1772 1772 — — —AT- 1 6 9
LC/B SOLENOID FNCT P1774 1774 — — —AT- 1 7 2
BRAKE SW/CIRCUIT P1805 1805 — —×EC-551
APP SEN 1/CIRC P2122 2122 — — —EC-556
APP SEN 1/CIRC P2123 2123 — — —EC-556
APP SEN 2/CIRC P2127 2127 — — —EC-562
APP SEN 2/CIRC P2128 2128 — — —EC-562
TP SENSOR P2135 2135 — — —EC-569
APP SENSOR P2138 2138 — — —EC-576
Items
(CONSULT-II screen terms)DTC*
1
SRT codeTest value/
Test limit
(GST only)1st trip DTCReference
page CONSULT-II
GST*
2ECM*3

TROUBLE DIAGNOSIS
EC-77
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: August 20072004 QX56
Fail-safe ChartUBS00GZY
When the DTC listed below is detected, the ECM enters fail-safe mode and the MIL lights up.
2
P0037 P0038 P0057 P0058 Heated oxygen sensor 2 heater

P0138 P0139 P0158 P0159 P1146 P1147 P1166 P1167 Heated oxygen sensor 2

P0441 EVAP control system purge flow monitoring

P0444 P0445 P1444 EVAP canister purge volume control solenoid valve

P0447 P1446 EVAP canister vent control valve

P0451 P0452 P0453 EVAP control system pressure sensor

P0550 Power steering pressure sensor

P0700 P0710 P0720 P0740 P0744 P0745 P1706 P1716 P1730 P1752 P1754 P1757 P1759 P1762 P1764 P1767
P1769 P1772 P1774 A/T related sensors and solenoid valves

P1031 P1032 P1051 P1052 A/F sensor 1 heater

P1065 ECM power supply

P1122 Electric throttle control function

P1124 P1126 P1128 Electric throttle control actuator

P1217 Engine over temperature (OVERHEAT)

P1271 P1272 P1273 P1274 P1276 P1278 P1279 P1281 P1282 P1283 P1284 P1286 P1288 P1289 A/F sensor 1

P1805 Brake switch
3

P0171 P0172 P0174 P0175 Fuel injection system function

P0300 - P0308 Misfire

P0420 P0430 Three way catalyst function

P0442 P0456 EVAP control system (SMALL LEAK, VERY SMALL LEAK)

P0455 EVAP control system (GROSS LEAK)

P0506 P0507 Idle speed control system

P1121 Electric throttle control actuator

P1148 P1168 Closed loop control

P1211 TCS control unit

P1212 TCS communication line

P1564 ICC steering switch/ASCD steering switch

P1568 ICC command value

P1572 ICC brake switch/ASCD brake switch

P1574 ICC vehicle speed sensor/ASCD vehicle speed sensor Priority Detected items (DTC)
DTC No. Detected items Engine operating condition in fail-safe mode
P0101
P0102
P0103Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118Engine coolant tempera-
ture sensor circuitEngine coolant temperature will be determined by ECM based on the time after turning
ignition switch ON or START.
CONSULT-II displays the engine coolant temperature decided by ECM.
ConditionEngine coolant temperature decided
(CONSULT-II display)
Just as ignition switch is turned
ON or START40°C (104°F)
More than approx. 4 minutes after
ignition ON or START80°C (176°F)
Except as shown above40 - 80°C (104 - 176°F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.

TROUBLE DIAGNOSIS
EC-109
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: August 20072004 QX56P/N POSI SW
[ON/OFF]××
Indicates [ON/OFF] condition from the park/
neutral position (PNP) switch signal.
PW/ST SIGNAL
[ON/OFF]××

[ON/OFF] condition of the power steering sys-
tem (determined by the signal voltage of the
power steering pressure sensor signal) is indi-
cated.
LOAD SIGNAL
[ON/OFF]××

Indicates [ON/OFF] condition from the electri-
cal load signal.
ON: Rear window defogger switch is ON and/
or lighting switch is in 2nd position.
OFF: Both rear window defogger switch and
lighting switch are OFF.
IGNITION SW
[ON/OFF]

Indicates [ON/OFF] condition from ignition
switch signal.
HEATER FAN SW
[ON/OFF]

Indicates [ON/OFF] condition from the heater
fan switch signal.
BRAKE SW
[ON/OFF]

Indicates [ON/OFF] condition from the stop
lamp switch signal.
INJ PULSE-B1
[msec]×

Indicates the actual fuel injection pulse width
compensated by ECM according to the input
signals.
When the engine is stopped, a certain
computed value is indicated.
INJ PULSE-B2
[msec]
IGN TIMING
[BTDC]×

Indicates the ignition timing computed by ECM
according to the input signals.
When the engine is stopped, a certain
value is indicated.
CAL/LD VALUE [%]

“Calculated load value” indicates the value of
the current air flow divided by peak air flow.
MASS AIRFLOW
[g·m/s]

Indicates the mass air flow computed by ECM
according to the signal voltage of the mass air
flow sensor.
PURG VOL C/V
[%]

Indicates the EVAP canister purge volume
control solenoid valve control value computed
by the ECM according to the input signals.

The opening becomes larger as the value
increases.
AIR COND RLY
[ON/OFF]×

The air conditioner relay control condition
(determined by ECM according to the input
signals) is indicated.
FUEL PUMP RLY
[ON/OFF]×

Indicates the fuel pump relay control condition
determined by ECM according to the input sig-
nals.
VENT CONT/V
[ON/OFF]

The control condition of the EVAP canister
vent control valve (determined by ECM
according to the input signals) is indicated.
ON: Closed
OFF: Open
THRTL RELAY
[ON/OFF]

Indicates the throttle control motor relay con-
trol condition determined by the ECM accord-
ing to the input signals.
COOLING FAN
[HI/OFF]

The control condition of the cooling fan (deter-
mined by ECM according to the input signals)
is indicated.
ON: Operating
OFF: Stop Monitored item
[Unit]ECM
INPUT
SIG-
NALSMAIN
SIG-
NALSDescription Remarks

TROUBLE DIAGNOSIS
EC-119
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: August 20072004 QX56
PW/ST SIGNAL
Engine: After warming up, idle
the engineSteering wheel is in neutral position.
(Forward direction)OFF
Steering wheel is turned. ON
LOAD SIGNAL

Ignition switch: ONRear window defogger switch is ON
and/or lighting switch is in 2nd.ON
Rear window defogger switch is OFF
and lighting switch is OFF.OFF
IGNITION SW

Ignition switch: ON → OFF → ON ON → OFF → ON
HEATER FAN SW

Engine: After warming up, idle
the engineHeater fan is operating. ON
Heater fan is not operating OFF
BRAKE SW

Ignition switch: ONBrake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
INJ PULSE-B1
INJ PULSE-B2

Engine: After warming up

Air conditioner switch: OFF

Shift lever: N

no loadIdle 2.0 - 2.8 msec
2,000 rpm 1.9 - 2.9 msec
IGN TIMING

Engine: After warming up

Air conditioner switch: OFF

Shift lever: N

no loadIdle 14° - 18° BTDC
2,000 rpm 25° - 45° BTDC
CAL/LD VALUE

Engine: After warming up

Air conditioner switch: OFF

Shift lever: N

no loadIdle 14% - 33%
2,500 rpm 12% - 25%
MASS AIRFLOW

Engine: After warming up

Air conditioner switch: OFF

Shift lever: N

no loadIdle 3.0 - 9.0 g·m/s
2,500 rpm 9.0 - 28.0 g·m/s
PURG VOL C/V

Engine: After warming up

Air conditioner switch: OFF

Shift lever: N

no loadIdle
(Accelerator pedal is not depressed
even slightly, after starting engine)0%
2,000 rpm —
AIR COND RLY

Engine: After warming up, idle
the engineAir conditioner switch: OFF OFF
Air conditioner switch: ON
(Compressor operates)ON
FUEL PUMP RLY

For 1 second after turning ignition switch ON

Engine running or crankingON

Except above conditions OFF
VENT CONT/V

Ignition switch: ON OFF
THRTL RELAY

Ignition switch: ON ON
COOLING FAN

Engine: After warming up, idle
the engine

Air conditioner switch: OFFEngine coolant temperature is 99°C
(210°F) or lessOFF
Engine coolant temperature is
between 100°C (212°F) and 104°C
(219°F) at vehicle speed less than 40
km/h (25 MPH)ON
Engine coolant temperature is 105°C
(221°F) or moreON MONITOR ITEM CONDITION SPECIFICATION