2004 INFINITI FX35 Fuel system

EC-8Revision: 2004 November 2004 FX35/FX45 PREPARATION .......................................................674
Special Service Tools ...........................................674
Commercial Service Tools ....................................675
ENGINE CONTROL SYSTEM ................................676
System Diagram ...................................................676
Vacuum Hose Drawing .........................................677
System Chart ........................................................678
Multiport Fuel Injection (MFI) System ...................679
Electronic Ignition (EI) System .............................681
Nissan Torque Demand (NTD) Control System ....682
Air Conditioning Cut Control .................................683
Fuel Cut Control (at No Load and High Engine
Speed) ..................................................................683
CAN communication .............................................684
BASIC SERVICE PROCEDURE .............................685
Idle Speed and Ignition Timing Check ..................685
Idle Speed/Ignition Timing/Idle Mixture Ratio
Adjustment ............................................................687
Accelerator Pedal Released Position Learning ....698
Throttle Valve Closed Position Learning ...............698
Idle Air Volume Learning ......................................698
Fuel Pressure Check ............................................700
ON BOARD DIAGNOSTIC (OBD) SYSTEM ..........703
Introduction ...........................................................703
Two Trip Detection Logic ......................................703
Emission-related Diagnostic Information ..............704
IVIS (Infiniti Vehicle Immobilizer System — NATS) .717
Malfunction Indicator Lamp (MIL) .........................717
OBD System Operation Chart ..............................721
TROUBLE DIAGNOSIS ..........................................726
Trouble Diagnosis Introduction .............................726
DTC Inspection Priority Chart ...............................729
Fail-safe Chart ......................................................731
Basic Inspection ...................................................733
Symptom Matrix Chart ..........................................738
Engine Control Component Parts Location ..........742
Circuit Diagram .....................................................748
ECM Harness Connector Terminal Layout ...........750
ECM Terminals and Reference Value ...................750
CONSULT-II Function ...........................................759
Generic Scan Tool (GST) Function .......................772
CONSULT-II Reference Value in Data Monitor .....775
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................778
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .780
Description ............................................................780
Testing Condition ..................................................780
Inspection Procedure ............................................780
Diagnostic Procedure ...........................................781
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................784
Description ............................................................784
Diagnostic Procedure ...........................................784
POWER SUPPLY AND GROUND CIRCUIT ...........785
Wiring Diagram .....................................................785
Diagnostic Procedure ...........................................786
Ground Inspection ................................................791
DTC U1000, U1001 CAN COMMUNICATION LINE .792
Description ............................................................792On Board Diagnosis Logic ....................................792
DTC Confirmation Procedure ................................792
Wiring Diagram .....................................................793
Diagnostic Procedure ............................................794
DTC P0011, P0021 IVT CONTROL .........................795
Description ............................................................795
CONSULT-II Reference Value in Data Monitor Mode
.796
On Board Diagnosis Logic ....................................796
DTC Confirmation Procedure ................................797
Wiring Diagram .....................................................798
Diagnostic Procedure ............................................801
Component Inspection ..........................................805
Removal and Installation .......................................805
DTC P0031, P0032, P0051, P0052 HO2S1 HEATER .806
Description ............................................................806
CONSULT-II Reference Value in Data Monitor Mode
.806
On Board Diagnosis Logic ....................................806
DTC Confirmation Procedure ................................807
Wiring Diagram .....................................................808
Diagnostic Procedure ............................................811
Component Inspection ..........................................813
Removal and Installation .......................................813
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .814
Description ............................................................814
CONSULT-II Reference Value in Data Monitor Mode
.814
On Board Diagnosis Logic ....................................814
DTC Confirmation Procedure ................................815
Wiring Diagram .....................................................816
Diagnostic Procedure ............................................819
Component Inspection ..........................................821
Removal and Installation .......................................821
DTC P0101 MAF SENSOR .....................................822
Component Description ........................................822
CONSULT-II Reference Value in Data Monitor Mode
.822
On Board Diagnosis Logic ....................................822
DTC Confirmation Procedure ................................823
Overall Function Check .........................................824
Wiring Diagram .....................................................825
Diagnostic Procedure ............................................826
Component Inspection ..........................................829
Removal and Installation .......................................829
DTC P0102, P0103 MAF SENSOR .........................830
Component Description ........................................830
CONSULT-II Reference Value in Data Monitor Mode
.830
On Board Diagnosis Logic ....................................830
DTC Confirmation Procedure ................................831
Wiring Diagram .....................................................832
Diagnostic Procedure ............................................833
Component Inspection ..........................................836
Removal and Installation .......................................836
DTC P0112, P0113 IAT SENSOR ............................837
Component Description ........................................837
On Board Diagnosis Logic ....................................837
DTC Confirmation Procedure ................................837

EC-9
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: 2004 November 2004 FX35/FX45Wiring Diagram .................................................... 839
Diagnostic Procedure ........................................... 840
Component Inspection ......................................... 841
Removal and Installation ...................................... 841
DTC P0117, P0118 ECT SENSOR ......................... 842
Component Description ........................................ 842
On Board Diagnosis Logic ................................... 842
DTC Confirmation Procedure ............................... 843
Wiring Diagram .................................................... 844
Diagnostic Procedure ........................................... 845
Component Inspection ......................................... 846
Removal and Installation ...................................... 847
DTC P0122, P0123 TP SENSOR ........................... 848
Component Description ........................................ 848
CONSULT-II Reference Value in Data Monitor Mode
. 848
On Board Diagnosis Logic ................................... 848
DTC Confirmation Procedure ............................... 849
Wiring Diagram .................................................... 850
Diagnostic Procedure ........................................... 851
Component Inspection ......................................... 854
Removal and Installation ...................................... 854
DTC P0125 ECT SENSOR ..................................... 855
Component Description ........................................ 855
On Board Diagnosis Logic ................................... 855
DTC Confirmation Procedure ............................... 856
Diagnostic Procedure ........................................... 856
Component Inspection ......................................... 857
Removal and Installation ...................................... 857
DTC P0127 IAT SENSOR ....................................... 858
Component Description ........................................ 858
On Board Diagnosis Logic ................................... 858
DTC Confirmation Procedure ............................... 858
Diagnostic Procedure ........................................... 859
Component Inspection ......................................... 860
Removal and Installation ...................................... 860
DTC P0128 THERMOSTAT FUNCTION ................ 861
On Board Diagnosis Logic ................................... 861
DTC Confirmation Procedure ............................... 861
Diagnostic Procedure ........................................... 861
Component Inspection ......................................... 862
Removal and Installation ...................................... 862
DTC P0132, P0152 HO2S1 .................................... 863
Component Description ........................................ 863
CONSULT-II Reference Value in Data Monitor Mode
. 863
On Board Diagnosis Logic ................................... 863
DTC Confirmation Procedure ............................... 864
Wiring Diagram .................................................... 865
Diagnostic Procedure ........................................... 868
Component Inspection ......................................... 870
Removal and Installation ...................................... 871
DTC P0133, P0153 HO2S1 .................................... 872
Component Description ........................................ 872
CONSULT-II Reference Value in Data Monitor Mode
. 872
On Board Diagnosis Logic ................................... 872
DTC Confirmation Procedure ............................... 873
Overall Function Check ........................................ 874Wiring Diagram .....................................................875
Diagnostic Procedure ...........................................878
Component Inspection ..........................................882
Removal and Installation ......................................883
DTC P0134, P0154 HO2S1 .....................................884
Component Description ........................................884
CONSULT-II Reference Value in Data Monitor Mode
.884
On Board Diagnosis Logic ....................................884
DTC Confirmation Procedure ...............................885
Overall Function Check ........................................886
Wiring Diagram .....................................................887
Diagnostic Procedure ...........................................890
Component Inspection ..........................................892
Removal and Installation ......................................893
DTC P0138, P0158 HO2S2 .....................................894
Component Description ........................................894
CONSULT-II Reference Value in Data Monitor Mode
.894
On Board Diagnosis Logic ....................................894
DTC Confirmation Procedure ...............................895
Wiring Diagram .....................................................896
Diagnostic Procedure ...........................................899
Component Inspection ..........................................901
Removal and Installation ......................................902
DTC P0139, P0159 HO2S2 .....................................903
Component Description ........................................903
CONSULT-II Reference Value in Data Monitor Mode
.903
On Board Diagnosis Logic ....................................903
DTC Confirmation Procedure ...............................904
Overall Function Check ........................................904
Wiring Diagram .....................................................906
Diagnostic Procedure ...........................................909
Component Inspection ..........................................912
Removal and Installation ......................................913
DTC P0171, P0174 FUEL INJECTION SYSTEM
FUNCTION ..............................................................914
On Board Diagnosis Logic ....................................914
DTC Confirmation Procedure ...............................914
Wiring Diagram .....................................................916
Diagnostic Procedure ...........................................918
DTC P0172, P0175 FUEL INJECTION SYSTEM
FUNCTION ..............................................................923
On Board Diagnosis Logic ....................................923
DTC Confirmation Procedure ...............................923
Wiring Diagram .....................................................925
Diagnostic Procedure ...........................................927
DTC P0181 FTT SENSOR ......................................931
Component Description ........................................931
On Board Diagnosis Logic ....................................931
DTC Confirmation Procedure ...............................931
Wiring Diagram .....................................................933
Diagnostic Procedure ...........................................934
Component Inspection ..........................................936
Removal and Installation ......................................936
DTC P0182, P0183 FTT SENSOR ..........................937
Component Description ........................................937
On Board Diagnosis Logic ....................................937

EC-11
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: 2004 November 2004 FX35/FX45DTC P0456 EVAP CONTROL SYSTEM ...............1030
On Board Diagnosis Logic ..................................1030
DTC Confirmation Procedure ..............................1031
Overall Function Check .......................................1032
Diagnostic Procedure ..........................................1033
DTC P0460 FUEL LEVEL SENSOR .....................1040
Component Description .......................................1040
On Board Diagnosis Logic ..................................1040
DTC Confirmation Procedure ..............................1040
Diagnostic Procedure ..........................................1041
Removal and Installation .....................................1041
DTC P0461 FUEL LEVEL SENSOR .....................1042
Component Description .......................................1042
On Board Diagnosis Logic ..................................1042
Overall Function Check .......................................1042
Diagnostic Procedure ..........................................1043
Removal and Installation .....................................1043
DTC P0462, P0463 FUEL LEVEL SENSOR CIR-
CUIT .......................................................................1044
Component Description .......................................1044
On Board Diagnosis Logic ..................................1044
DTC Confirmation Procedure ..............................1044
Diagnostic Procedure ..........................................1045
Removal and Installation .....................................1045
DTC P0500 VSS ....................................................1046
Description ..........................................................1046
On Board Diagnosis Logic ..................................1046
DTC Confirmation Procedure ..............................1046
Overall Function Check .......................................1047
Diagnostic Procedure ..........................................1047
DTC P0506 ISC SYSTEM ......................................1048
Description ..........................................................1048
On Board Diagnosis Logic ..................................1048
DTC Confirmation Procedure ..............................1048
Diagnostic Procedure ..........................................1049
DTC P0507 ISC SYSTEM ......................................1050
Description ..........................................................1050
On Board Diagnosis Logic ..................................1050
DTC Confirmation Procedure ..............................1050
Diagnostic Procedure ..........................................1051
DTC P0550 PSP SENSOR ....................................1052
Component Description .......................................1052
CONSULT-II Reference Value in Data Monitor Mode
1052
On Board Diagnosis Logic ..................................1052
DTC Confirmation Procedure ..............................1052
Wiring Diagram ...................................................1053
Diagnostic Procedure ..........................................1054
Component Inspection ........................................1056
Removal and Installation .....................................1056
DTC P0605 ECM ...................................................1057
Component Description .......................................1057
On Board Diagnosis Logic ..................................1057
DTC Confirmation Procedure ..............................1057
Diagnostic Procedure ..........................................1058
DTC P1065 ECM POWER SUPPLY ......................1060
Component Description .......................................1060
On Board Diagnosis Logic ..................................1060
DTC Confirmation Procedure ..............................1060Wiring Diagram ....................................................1061
Diagnostic Procedure ..........................................1062
DTC P1102 MAF SENSOR ....................................1064
Component Description .......................................1064
CONSULT-II Reference Value in Data Monitor Mode
1064
On Board Diagnosis Logic ...................................1064
DTC Confirmation Procedure ..............................1065
Wiring Diagram ....................................................1066
Diagnostic Procedure ..........................................1067
Component Inspection .........................................1069
Removal and Installation .....................................1069
DTC P1111, P1136 IVT CONTROL SOLENOID
VALVE ....................................................................1070
Component Description .......................................1070
CONSULT-II Reference Value in Data Monitor Mode
1070
On Board Diagnosis Logic ...................................1070
DTC Confirmation Procedure ..............................1070
Wiring Diagram ....................................................1071
Diagnostic Procedure ..........................................1074
Component Inspection .........................................1076
Removal and Installation .....................................1076
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR ............................................................1077
Component Description .......................................1077
On Board Diagnosis Logic ...................................1077
DTC Confirmation Procedure ..............................1077
Diagnostic Procedure ..........................................1078
DTC P1122 ELECTRIC THROTTLE CONTROL
FUNCTION .............................................................1079
Description ...........................................................1079
On Board Diagnosis Logic ...................................1079
DTC Confirmation Procedure ..............................1079
Wiring Diagram ....................................................1080
Diagnostic Procedure ..........................................1081
Component Inspection .........................................1084
Removal and Installation .....................................1084
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY ....................................................................1085
Component Description .......................................1085
CONSULT-II Reference Value in Data Monitor Mode
1085
On Board Diagnosis Logic ...................................1085
DTC Confirmation Procedure ..............................1085
Wiring Diagram ....................................................1087
Diagnostic Procedure ..........................................1088
DTC P1128 THROTTLE CONTROL MOTOR ........1090
Component Description .......................................1090
On Board Diagnosis Logic ...................................1090
DTC Confirmation Procedure ..............................1090
Wiring Diagram ....................................................1091
Diagnostic Procedure ..........................................1092
Component Inspection .........................................1093
Removal and Installation .....................................1094
DTC P1140, P1145 IVT CONTROL POSITION SEN-
SOR ........................................................................1095
Component Description .......................................1095
CONSULT-II Reference Value in Data Monitor Mode

EC-14Revision: 2004 November 2004 FX35/FX45CONSULT-II Reference Value in Data Monitor Mode
1255
Wiring Diagram ....................................................1256
Diagnostic Procedure ..........................................1257
Component Inspection .........................................1260
Removal and Installation .....................................1261
IGNITION SIGNAL .................................................1262
Component Description .......................................1262
Wiring Diagram ....................................................1263
Diagnostic Procedure ..........................................1268
Component Inspection .........................................1272
Removal and Installation .....................................1273
INJECTOR CIRCUIT ..............................................1274
Component Description .......................................1274
CONSULT-II Reference Value in Data Monitor Mode
1274
Wiring Diagram ....................................................1275
Diagnostic Procedure ..........................................1276
Component Inspection .........................................1279
Removal and Installation .....................................1279
FUEL PUMP CIRCUIT ...........................................1280
Description ...........................................................1280
CONSULT-II Reference Value in Data Monitor Mode
1280
Wiring Diagram ....................................................1281
Diagnostic Procedure ..........................................1282
Component Inspection .........................................1285
Removal and Installation .....................................1286
REFRIGERANT PRESSURE SENSOR .................1287
Component Description .......................................1287
Wiring Diagram ....................................................1288
Diagnostic Procedure ..........................................1289
Removal and Installation .....................................1291
ELECTRICAL LOAD SIGNAL ...............................1292
Description ...........................................................1292
CONSULT-II Reference Value in Data Monitor Mode
1292
Diagnostic Procedure ..........................................1292
ICC BRAKE SWITCH .............................................1293
Component Description .......................................1293
CONSULT-II Reference Value in Data Monitor Mode
1293
Wiring Diagram ....................................................1294
Diagnostic Procedure ..........................................1295
Component Inspection .........................................1301
ASCD BRAKE SWITCH .........................................1302
Component Description .......................................1302
CONSULT-II Reference Value in Data Monitor Mode
1302Wiring Diagram ....................................................1303
Diagnostic Procedure ...........................................1304
Component Inspection .........................................1308
ASCD INDICATOR .................................................1309
Component Description .......................................1309
CONSULT-II Reference Value in Data Monitor Mode
1309
Wiring Diagram ....................................................1310
Diagnostic Procedure ...........................................1311
SNOW MODE SWITCH ..........................................1312
Description ...........................................................1312
CONSULT-II Reference Value in the Data Monitor
Mode ....................................................................1312
Wiring Diagram ....................................................1313
Diagnostic Procedure ...........................................1314
Component Inspection .........................................1317
MIL AND DATA LINK CONNECTOR .....................1318
Wiring Diagram ....................................................1318
EVAPORATIVE EMISSION SYSTEM ....................1320
Description ...........................................................1320
Component Inspection .........................................1323
Removal and Installation ......................................1324
How to Detect Fuel Vapor Leakage .....................1324
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ...................................................................1327
System Description ..............................................1327
Diagnostic Procedure ...........................................1328
Component Inspection .........................................1330
POSITIVE CRANKCASE VENTILATION ...............1332
Description ...........................................................1332
Component Inspection .........................................1332
AUTOMATIC SPEED CONTROL DEVICE (ASCD) 1334
System Description ..............................................1334
Component Description .......................................1335
SERVICE DATA AND SPECIFICATIONS (SDS) ...1336
Fuel Pressure .......................................................1336
Idle Speed and Ignition Timing .............................1336
Calculated Load Value .........................................1336
Mass Air Flow Sensor ..........................................1336
Intake Air Temperature Sensor ............................1336
Engine Coolant Temperature Sensor ...................1336
Heated Oxygen Sensor 1 Heater .........................1336
Heated Oxygen Sensor 2 Heater .........................1336
Crankshaft Position Sensor (POS) ......................1336
Camshaft Position Sensor (PHASE) ....................1336
Throttle Control Motor ..........................................1336
Injector .................................................................1337
Fuel Pump ............................................................1337

EC-20
[VQ35DE]
INDEX FOR DTC
Revision: 2004 November 2004 FX35/FX45
P0159 0159 HO2S2 (B2) 2×EC-245
P0171 0171 FUEL SYS-LEAN-B1 2×EC-256
P0172 0172 FUEL SYS-RICH-B1 2×EC-265
P0174 0174 FUEL SYS-LEAN-B2 2×EC-256
P0175 0175 FUEL SYS-RICH-B2 2×EC-265
P0181 0181 FTT SENSOR 2×EC-273
P0182 0182 FTT SEN/CIRCUIT 2×EC-279
P0183 0183 FTT SEN/CIRCUIT 2×EC-279
P0222 0222 TP SEN 1/CIRC 1×EC-284
P0223 0223 TP SEN 1/CIRC 1×EC-284
P0300 0300 MULTI CYL MISFIRE 2×EC-291
P0301 0301 CYL 1 MISFIRE 2×EC-291
P0302 0302 CYL 2 MISFIRE 2×EC-291
P0303 0303 CYL 3 MISFIRE 2×EC-291
P0304 0304 CYL 4 MISFIRE 2×EC-291
P0305 0305 CYL 5 MISFIRE 2×EC-291
P0306 0306 CYL 6 MISFIRE 2×EC-291
P0327 0327 KNOCK SEN/CIRC-B1 2 —EC-297
P0328 0328 KNOCK SEN/CIRC-B1 2 —EC-297
P0335 0335 CKP SEN/CIRCUIT 2×EC-302
P0340 0340 CMP SEN/CIRC-B1 2×EC-308
P0345 0345 CMP SEN/CIRC-B2 2×EC-308
P0420 0420 TW CATALYST SYS-B1 2×EC-316
P0430 0430 TW CATALYST SYS-B2 2×EC-316
P0441 0441 EVAP PURG FLOW/MON 2×EC-321
P0442 0442 EVAP SMALL LEAK 2×EC-326
P0444 0444 PURG VOLUME CONT/V 2×EC-335
P0445 0445 PURG VOLUME CONT/V 2×EC-335
P0447 0447 VENT CONTROL VALVE 2×EC-342
P0451 0451 EVAP SYS PRES SEN 2×EC-349
P0452 0452 EVAP SYS PRES SEN 2×EC-352
P0453 0453 EVAP SYS PRES SEN 2×EC-358
P0455 0455 EVAP GROSS LEAK 2×EC-366
P0456 0456 EVAP VERY SML LEAK 2×EC-374
P0460 0460 FUEL LEV SEN SLOSH 2×EC-384
P0461 0461 FUEL LEVEL SENSOR 2×EC-386
P0462 0462 FUEL LEVL SEN/CIRC 2×EC-388
P0463 0463 FUEL LEVL SEN/CIRC 2×EC-388
P0500 0500
VEH SPEED SEN/CIRC*62×EC-390
P0506 0506 ISC SYSTEM 2×EC-392
P0507 0507 ISC SYSTEM 2×EC-394
P0550 0550 PW ST P SEN/CIRC 2 —EC-396
DTC*1
Items
(CONSULT-II screen terms)TripMIL lighting
upReference page
CONSULT-II
GST*
2ECM*3

PRECAUTIONS
EC-23
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2004 November 2004 FX35/FX45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ABS00A2R
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
On Board Diagnostic (OBD) System of Engine and A/TABS006JZ
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:

Be sure to turn the ignition switch OFF and disconnect the negative battery cable before any
repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves,
etc. will cause the MIL to light up.

Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to the open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)

Certain systems and components, especially those related to OBD, may use a new style slide-
locking type harness connector. For description and how to disconnect, refer to PG-74, "
HAR-
NESS CONNECTOR" .

Be sure to route and secure the harnesses properly after work. The interference of the harness
with a bracket, etc. may cause the MIL to light up due to the short circuit.

Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to the malfunction of the EVAP system or fuel injection system,
etc.

Be sure to erase the unnecessary malfunction information (repairs completed) from the ECM and
TCM (Transmission control module) before returning the vehicle to the customer.
PrecautionABS006K0

Always use a 12 volt battery as power source.

Do not attempt to disconnect battery cables while engine is
running.

Before connecting or disconnecting the ECM harness con-
nector, turn ignition switch OFF and disconnect negative
battery cable. Failure to do so may damage the ECM
because battery voltage is applied to ECM even if ignition
switch is turned OFF.

Before removing parts, turn ignition switch OFF and then
disconnect negative battery cable.
SEF289H

EC-26
[VQ35DE]
PRECAUTIONS
Revision: 2004 November 2004 FX35/FX45

Do not operate fuel pump when there is no fuel in lines.

Tighten fuel hose clamps to the specified torque.

Do not depress accelerator pedal when starting.

Immediately after starting, do not rev up engine unneces-
sarily.

Do not rev up engine just prior to shutdown.

When installing C.B. ham radio or a mobile phone, be sure
to observe the following as it may adversely affect elec-
tronic control systems depending on installation location.
–Keep the antenna as far as possible from the electronic
control units.
–Keep the antenna feeder line more than 20 cm (8 in) away
from the harness of electronic controls.
Do not let them run parallel for a long distance.
–Adjust the antenna and feeder line so that the standing-
wave radio can be kept smaller.
–Be sure to ground the radio to vehicle body.
Wiring Diagrams and Trouble DiagnosisABS006K1
When you read wiring diagrams, refer to the following:

GI-15, "How to Read Wiring Diagrams"

PG-3, "POWER SUPPLY ROUTING CIRCUIT" for power distribution circuit
When you perform trouble diagnosis, refer to the following:

GI-11, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES"

GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident"
PBIB1569E
SEF709Y
SEF708Y

EC-28
[VQ35DE]
PREPARATION
Revision: 2004 November 2004 FX35/FX45
Commercial Service ToolsABS006K3
Tool name
(Kent-Moore No.)Description
Leak detector
i.e.: (J-41416)Locating the EVAP leak
EVAP service port
adapter
i.e.: (J-41413-OBD)Applying positive pressure through EVAP service
port
Fuel filler cap adapter
i.e.: (MLR-8382)Checking fuel tank vacuum relief valve opening
pressure
Socket wrench Removing and installing engine coolant
temperature sensor
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12)Reconditioning the exhaust system threads
before installing a new oxygen sensor. Use with
anti-seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for
Zirconia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for
Titania Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL
specification MIL-A-
907)Lubricating oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
S-NT703
S-NT704
S-NT815
S-NT705
AEM488
S-NT779