2004 INFINITI FX35 pg power

POWER SEAT
SE-93
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2004 November 2004 FX35/FX45
POWER SEATPFP:87016
Automatic Drive Positioner Interlocking Power SeatAIS003L4
A trouble diagnosis of a automatic drive positioner interlocking power seat is refer toSE-11, "AUTOMATIC
DRIVE POSITIONER" .

SE-94
POWER SEAT
Revision: 2004 November 2004 FX35/FX45
SchematicAIS003LF
TIWM0302E

POWER SEAT
SE-95
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2004 November 2004 FX35/FX45
Wiring Diagram–SEAT– / For Driver SeatAIS002X1
TIWM0303E

SE-96
POWER SEAT
Revision: 2004 November 2004 FX35/FX45
TIWM0304E

POWER SEAT
SE-97
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2004 November 2004 FX35/FX45
Wiring Diagram–SEAT– / For Passenger SeatAIS002X2
TIWM0305E

SE-102
FRONT SEAT
Revision: 2004 November 2004 FX35/FX45
1. Headrest 2. Headrest holder (Free) 3. Headrest holder (Looked)
4. Seatback pad 5. Seatback trim 6. Seat cushion inner finisher
7. Screw 8. Power seat switch assembly 9. Seat cushion trim
10. Seat cushion pad 11. Seatback garnish 12. Nut
13. Side air bag module 14. Clip (C101) 15. Inner cloth stay
16. Lumber support device 17. Bolt 18. Seatback frame
19. Reclining device assembly 20. Seat cushion frame 21. Seat harness assembly
22. Seat adjust assembly 23. Clip (C103) 24. Seat adjust assembly cover
25. Seat cushion outer finisher 26. Seat cushion outer finisher cover 27. Power seat memory switch assembly
28. Seat cushion forward finisher 29. Seat cushion forward finisher lid

FRONT SEAT
SE-103
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2004 November 2004 FX35/FX45
REMOVAL
When removing or installing the seat trim, carefully handle it to keep dirt out and avoid damage.
CAUTION:

Before removing the front seat, turn ignition switch OFF, disconnect both battery cables and wait
at least 3 minutes.

When checking the power seat circuit for continuity using a circuit tester, do not confuse its con-
nector with the side air bag module connector. Such an error may cause the air bag to deploy.

Do not drop, tilt, or bump the side air bag module installing in the seat. Always handle it with care.
1. Remove the seat cushion outer finisher cover.
2. Remove the front seat belt anchor bolt. Refer toSB-4, "
Removal
and Installation of Front Seat Belt" .
CAUTION:
Set the front and rear cushion lifter to the down position.
3. Remove the screw.
4. Remove the seat cushion forward finisher lid.
5. Remove the seat cushion forward finisher.
6. Remove the seat cushion outer finisher.
7. Remove the power seat memory switch assembly.
PIIA6040E
PIIA6039E
1. Screw 2. Seat cushion forward finisher 3. Seat cushion outer finisher
4. Clip(C101)

SE-104
FRONT SEAT
Revision: 2004 November 2004 FX35/FX45
8. Remove the front and rear leg cover (LH and RH).
NOTE:
1. Slide the seat backward, and disconnect the front tabs on the front leg cover. Then move the cover
toward the rear of the vehicle, and pull up to remove.
2. Slide the seat forward, then disengage the tabs on the front LH and RH of the rear leg cover and tabs
engaged into the rail. Then pull the cover toward the rear of the vehicle.
9. Slide the seat until the body mounting bolts are visible and a tool can be inserted.
NOTE:
When disassembling the driver seat after removal, set the front and rear cushion lifter to the top position.
10. Disconnect both battery cables.
11. Remove the harness connector for the side air bag module.
12. Remove the power seat harness connector and vehicle harness fixing clip.
13. Remove the front seat.
NOTE:
When removing and installing, using waste, protect the parts from damage where it may interfere with oth-
ers.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Be sure to insert the rear end tab of the rear leg cover under the rail.
REMOVAL OF SEATBACK TRIM AND PAD
1. Remove the seatback garnish.
2. Remove the retainer.
PIIA4984E
PIIA6041E
PIIA6042E