2004 HONDA ACCORD COUPE Owners Manual

Move the steering wheel so it
points to your chest, not toward
your f ace. Make sure you can see
the instrument panel gauges and
indicators.
Push the lever up to lock the
steering wheel in position.
Make sure you have securely
locked the steering wheel in place
by trying to move it up, down, in,
and out.
Insert the key in the ignition
switch, and unlock the steering
column.
Push the lever under the steering
column all the way down.
Make any steering wheel adjustment
bef ore you start driving.
3. 4. 5.
2.
1.See page f or important saf ety
inf ormation about how to properlyposition the steering wheel. 15
Steering Wheel A djustment
Inst rument s and Cont rols74
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.
——y

y
(%
yy

The master key fits all the locks on
your vehicle. The valet key works
only in the ignition and the driver’s
door lock. You can keep the trunk
release handle, rear seat trunk
access, and glove box locked when
you leave your vehicle and the valet
key at a parking f acility.Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Use
only Honda-approved key blanks.
These keys contain electronic
circuits that are activated by the
Immobilizer System. They will not
work to start the engine if the
circuits are damaged.
Protect the keys f rom direct
sunlight, high temperature, and
high humidity.
Donotdropthekeysorsetheavy
objects on them.
Keep the keys away f rom liquids.
If they get wet, dry them
immediately with a sof t cloth.
Keys and Locks
Inst rument s and Cont rols75
MASTER
KEY WITH
REMOTE
TRANSMITTER VALET KEY
(LIGHT GREY)
KEY
NUMBERTAG
——y

y
(%
yy

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, including
interf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f or
compliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not cause
interf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.The Immobilizer System protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine’s f uel
system is disabled.
When you turn the ignition switch to
ON (II), the Immobilizer System
indicator should come on f or a f ew
seconds, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to
LOCK (0), remove the key, reinsert
it, and turn the switch to ON (II)
again. The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
f ob) is near the ignition switch when
you insert the key.
If the system repeatedly does not
recognize the coding of your key,
contact your Honda dealer.
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle undriveable.
If you have lost your key and cannot
start the engine, contact a Honda
dealer.
Immobilizer Syst em
Inst rument s and Cont rols76
——y

y
(%
yy

µµµ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III). You can insert or
remove the key only in this position.
To turn the key, you must push the
key in slightly. If your vehicle has an
automatic transmission, the shif t
lever must also be in park. If the f ront wheels are turned, the
anti-thef t lock may make it dif f icult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
You can
operate the audio system and the
accessory power sockets in this
position. This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom ACCESSORY
(I) to ON (II).
Use this position
only to start the engine. The switch
returns to ON (II) when you let go of
the key.
You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or
ACCESSORY (I) position and open
the driver’s door. Remove the key to
turn of f the beeper.
On automatic transmission model,
theshiftlevermustbeinPark
bef ore you can remove the key f rom
the ignition switch.
Ignition Switch
Inst rument s and Cont rols
LOCK (0) A CCESSORY (I)ON (II)
ST A RT (III)
77
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control.
Remove the key from the
ignition switch only whenparked.
——y


y
(%
yy

Youcanopenorclosethewindows
by using the key in the driver’s door
(see page ).
To unlock only the driver’s door
f rom the outside, turn the key and
releaseit.If youturnitagain,both
doors unlock.
The lock tab on the passenger’s door
lock and unlock only that door.
Pulling up on the driver’s door lock
tab only unlocks the driver’s door.
To lock both doors, push the top of
the master door lock switch on
either door, or press the lock tab
down on the driver’s door, or use the
keyontheoutsidelockonthedriver’s
door.
Pushing the bottom of either master
door lock switch will unlock both
doors. To lock the passenger’s door when
getting out of the vehicle, push the
lock tab down and close the door. To
lock the driver’s door, remove the
key f rom the ignition switch and
push the lock tab down or push the
top of the master switch, then close
the door.
With the driver’s door open and the
key in the ignition, both master door
lock switches are disabled. They are
not disabled if the driver’s door is
closed. Pushing the top of the switch
on the open passenger’s door will
lock both doors.
93
Power Door L ocks
Inst rument s and Cont rols
L ockout Prevent ion
78
MASTER DOOR LOCK SWITCH LOCK TAB
——y

y
(%
y
y

µµ
µ
µ
CONT INUED
Press this button once to
lock both doors. Some exterior lights
will f lash once. When you push
LOCK twice within 5 seconds, you
will hear a beep to verify that the
doors are locked and (if equipped)
that the security system has set. You
cannot lock it if either door is not
f ully closed or the key is in the
ignition switch. Press this button once
to unlock the driver’s door. Push it
twice to unlock the passenger’s door.
Some exterior lights will f lash twice
each time you push the button. If
you do not open either door within
30 seconds, they will automatically
relock and the security system sets
(except f or 4-cylinder LX model).
You cannot unlock it if the key is in
the ignition switch.
The ceiling light (if the ceiling light
switch is in the center position) and
the spotlights (if the switch is in the
Door position) will come on when
you press the UNLOCK button. If
you do not open either door, the
lights stay on f or about 30 seconds,
then f ade out. If you relock the doors
with the remote transmitter before
30 seconds have elapsed, the lights
will go of f immediately. You can also open both power
windows from outside the vehicle
with the remote transmitter (see
page ).
Press this
button f or about one second to open
the trunk. You cannot open it if the
key is in the ignition switch.
Pressthisbuttonfor
about two seconds to attract
attention: the horn will sound and
the exterior lights will f lash f or about
30 seconds. To cancel panic mode,
press any other button on the remote
transmitter or turn the ignition
switch to ON (II). 93
Remote Transmitter
Inst rument s and Cont rols
LOCK
UNL OCK
T RUNK REL EA SE
PA NIC
79
UNLOCK
BUTTONLOCK
BUTTON
TRUNK
RELEASE
BUTTON
PANIC
BUTTON LED
——y

y
(%
yy

Battery type: CR1616
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by a Honda dealer.
Inside the transmitter, separate
the inner cover f rom the keypad
by releasing the two tabs on the
cover.
Separate the transmitter by prying
its middle seam with your
f ingernail.
Remove the screw at the base of
the transmitter with a small
Phillips-head screwdriver.
To replace the battery: 1. 2. 3.
Remote Transmitter
Inst rument s and Cont rols
Replacing the Transmitter Battery
Remote Transmitter Care
80
SCREW BATTERY
TAB
——y

y
(%
yy

´
Remove the old battery from the
back of the inner cover, and note
the polarity. Make sure the
polarity of the new battery is the
same ( side f acing down), then
insert it into the back of the cover.
Install the parts in reverse order.
4. 5.
As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, including
interf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f or
compliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not cause
interf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Remote Transmitter
Inst rument s and Cont rols81
——y

y
(%
yy