2004 DAEWOO LACETTI sensor

5A1 – 116IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
RangePark/
Neutr
alRever
seD321
GearNR1st2nd3rd4th1st2nd3rd1st2nd1st
Solenoid Valve
1ONON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFF
Solenoid Valve
2ONONONOFFOFFOFFONOFFOFFONOFFON
Line Pressure
Control Sole-
noid Valve 3
(EDS 3)OFFOFFOFFONON/
OFFON/
OFFOFFONON/
OFFOFFONOFF
Line Pressure
Control Sole-
noid Valve 4
(EDS 4)ONOFFONONONOFFONONONONONON
Line Pressure
Control Sole-
noid Valve 5
(EDS 5)OFFOFFONONOFFOFFONONOFFONONON
Line Pressure
Control Sole-
noid Valve 6
(EDS 6)ONOFFONONONOFFONONONONONON
Brake BAAAAAAAA
Brake CH
Brake DH
Clutch EAAAAAA
Brake FHHHHHHH
Lock–up
ClutchA
A = Applied
H = Holding
ON = The solenoid is energized.
OFF = The solenoid is de–energized.
** = Manual Second–Third gear is only available above approximately 100 km/h (62 mph).
*** = Manual First–Second gear is only available above approximately 60 km/h (37 mph).
Note : Manual First–Third gear is also possible at high vehicle speed as a safety feature.
DIAGNOSTIC TROUBLE CODE(DTC) P0731
GEAR 1 INCORRECT RATIO
Circuit Description
The TCM uses transaxle input speed information and out-
put speed sensor to control line pressure, TCC apply and
release and transaxle shift patterns. This information is
also uses to calculate the appropriate operating gear ra-
tios and TCC slippage. Conditions for Setting the DTC.
Conditions for Setting The DTC
S Time since TCM reset is greater than 500 msec.
S Time since shift end is greater than 500 msec.S Transmission oil temperature is greater than –10°C
(14°F).
S System voltage is greater than 9 volts.
S No input speed error DTCs P0715, P0716, and
P0717.
S Output speed is greater than 256 rpm.
S Input speed is greater than 400 rpm.
S No gear shift active.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 117
DAEWOO V–121 BL4
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear.
S High line pressure
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction hasnot occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S Check for intermittent input speed sensor or output
speed sensor circuit problems.
S Check for possible incorrect calibration.
DTC P0731 – Gear 1 Incorrect Ratio
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
2Visually inspect the transaxle cooling system for
fluid leaks.
Was condition found and corrected?–Go to Step 7Go to Step 3
3Has the transaxle fluid checking procedure been
performed?–Go to Step 4Go to Trans-
axle fluid check
procedures
41. Using the scan tool record each transaxle drive
range.
2. Drive the vehicle in transaxle gear ranges 1,2,3
and D with TP greater than 15% and vehicle
speed greater than 16km/h(10mph) for five
seconds.
Does commanded gear ratio match ranges as
shown?1st = 2.719
2nd = 1.487
3rd = 1.000
4th = 0.717Refer to Diag-
nostic AidsGo to Step 5
5Perform line pressure check.
Was the condition found and corrected?–Go to Step 7Go to Step 6
6Check for possible clutch slippage.
Was the condition found and corrected?–Go to Step 7–
71. After the repair, use a scan tool
clear info"
function and road test the vehicle.
2. Review the
DTC info".
Has the last test failed or is the current DTC dis-
played?Replace trans-
axle assemblyRepair verified
exit DTC chart

5A1 – 118IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
RangePark/
Neutr
alRever
seD321
GearNR1st2nd3rd4th1st2nd3rd1st2nd1st
Solenoid Valve
1ONON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFF
Solenoid Valve
2ONONONOFFOFFOFFONOFFOFFONOFFON
Line Pressure
Control Sole-
noid Valve 3
(EDS 3)OFFOFFOFFONON/
OFFON/
OFFOFFONON/
OFFOFFONOFF
Line Pressure
Control Sole-
noid Valve 4
(EDS 4)ONOFFONONONOFFONONONONONON
Line Pressure
Control Sole-
noid Valve 5
(EDS 5)OFFOFFONONOFFOFFONONOFFONONON
Line Pressure
Control Sole-
noid Valve 6
(EDS 6)ONOFFONONONOFFONONONONONON
Brake BAAAAAAAA
Brake CH
Brake DH
Clutch EAAAAAA
Brake FHHHHHHH
Lock–up
ClutchA
A = Applied
H = Holding
ON = The solenoid is energized.
OFF = The solenoid is de–energized.
** = Manual Second–Third gear is only available above approximately 100 km/h (62 mph).
*** = Manual First–Second gear is only available above approximately 60 km/h (37 mph).
Note : Manual First–Third gear is also possible at high vehicle speed as a safety feature.
DIAGNOSTIC TROUBLE CODE(DTC) P0732
GEAR 2 INCORRECT RATIO
Circuit Description
The TCM uses transaxle input speed information and out-
put speed sensor to control line pressure, TCC apply and
release and transaxle shift patterns. This information is
also uses to calculate the appropriate operating gear ra-
tios and TCC slippage. Conditions for Setting the DTC.
Conditions for Setting The DTC
S Time since TCM reset is greater than 500 msec.
S Time since shift end is greater than 500 msec.S Transmission oil temperature is greater than –10°C
(14°F).
S System voltage is greater than 9 volts.
S No input speed error DTCs P0715, P0716 or
P0717.
S Output speed is greater than 256 rpm.
S Input speed is greater than 400 rpm.
S No gear shift active.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 119
DAEWOO V–121 BL4
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
3rd gear.
S High line pressure
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction hasnot occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S Check for intermittent input speed sensor or output
speed sensor circuit problems.
S Check for possible incorrect calibration.
DTC P0732 – Gear 2 Incorrect Ratio
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
2Visually inspect the transaxle cooling system for
fluid leaks.
Was condition found and corrected?–Go to Step 7Go to Step 3
3Has the transaxle fluid checking procedure been
performed?–Go to Step 4Go to Trans-
axle fluid check
procedures
41. Using the scan tool record each transaxle drive
range.
2. Drive the vehicle in transaxle gear ranges 1,2,3
and D with TP greater than 15% and vehicle
speed greater than 16km/h(10mph) for five
seconds.
Does commanded gear ratio match ranges as
shown?1st = 2.719
2nd = 1.487
3rd = 1.000
4th = 0.717Refer to Diag-
nostic AidsGo to Step 5
5Perform line pressure check.
Was the condition found and corrected?–Go to Step 7Go to Step 6
6Check for possible clutch slippage.
Was the condition found and corrected?–Go to Step 7–
71. After the repair, use a scan tool
clear info"
function and road test the vehicle.
2. Review the
DTC info".
Has the last test failed or is the current DTC dis-
played?Replace trans-
axle assemblyRepair verified
exit DTC chart

5A1 – 120IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
RangePark/
Neutr
alRever
seD321
GearNR1st2nd3rd4th1st2nd3rd1st2nd1st
Solenoid Valve
1ONON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFF
Solenoid Valve
2ONONONOFFOFFOFFONOFFOFFONOFFON
Line Pressure
Control Sole-
noid Valve 3
(EDS 3)OFFOFFOFFONON/
OFFON/
OFFOFFONON/
OFFOFFONOFF
Line Pressure
Control Sole-
noid Valve 4
(EDS 4)ONOFFONONONOFFONONONONONON
Line Pressure
Control Sole-
noid Valve 5
(EDS 5)OFFOFFONONOFFOFFONONOFFONONON
Line Pressure
Control Sole-
noid Valve 6
(EDS 6)ONOFFONONONOFFONONONONONON
Brake BAAAAAAAA
Brake CH
Brake DH
Clutch EAAAAAA
Brake FHHHHHHH
Lock–up
ClutchA
A = Applied
H = Holding
ON = The solenoid is energized.
OFF = The solenoid is de–energized.
** = Manual Second–Third gear is only available above approximately 100 km/h (62 mph).
*** = Manual First–Second gear is only available above approximately 60 km/h (37 mph).
Note : Manual First–Third gear is also possible at high vehicle speed as a safety feature.
DIAGNOSTIC TROUBLE CODE(DTC) P0733
GEAR 3 INCORRECT RATIO
Circuit Description
The TCM uses transaxle input speed information and out-
put speed sensor to control line pressure, TCC apply and
release and transaxle shift patterns. This information is
also uses to calculate the appropriate operating gear ra-
tios and TCC slippage. Conditions for Setting the DTC.
Conditions for Setting The DTC
S Time since TCM reset is greater than 500 msec.
S Time since shift end is greater than 500 msec.S Transmission oil temperature is greater than –10°C
(14°F).
S System voltage is greater than 9 volts.
S No input speed error DTCs P0715, P0716, and
P0717.
S Output speed is greater than 256 rpm.
S Input speed is greater than 400 rpm.
S No gear shift active.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 121
DAEWOO V–121 BL4
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear.
S High line pressure
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction hasnot occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S Check for intermittent input speed sensor or output
speed sensor circuit problems.
S Check for possible incorrect calibration.
DTC P0733 – Gear 3 Incorrect Ratio
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
2Visually inspect the transaxle cooling system for
fluid leaks.
Was condition found and corrected?–Go to Step 7Go to Step 3
3Has the transaxle fluid checking procedure been
performed?–Go to Step 4Go to Trans-
axle fluid check
procedures
41. Using the scan tool record each transaxle drive
range.
2. Drive the vehicle in transaxle gear ranges 1,2,3
and D with TP greater than 15% and vehicle
speed greater than 16km/h(10mph) for five
seconds.
Does commanded gear ratio match ranges as
shown?1st = 2.719
2nd = 1.487
3rd = 1.000
4th = 0.717Refer to Diag-
nostic AidsGo to Step 5
5Perform line pressure check.
Was the condition found and corrected?–Go to Step 7Go to Step 6
6Check for possible clutch slippage.
Was the condition found and corrected?–Go to Step 7–
71. After the repair, use a scan tool
clear info"
function and road test the vehicle.
2. Review the
DTC info".
Has the last test failed or is the current DTC dis-
played?Replace trans-
axle assemblyRepair verified
exit DTC chart

5A1 – 122IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
RangePark/
Neutr
alRever
seD321
GearNR1st2nd3rd4th1st2nd3rd1st2nd1st
Solenoid Valve
1ONON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFF
Solenoid Valve
2ONONONOFFOFFOFFONOFFOFFONOFFON
Line Pressure
Control Sole-
noid Valve 3
(EDS 3)OFFOFFOFFONON/
OFFON/
OFFOFFONON/
OFFOFFONOFF
Line Pressure
Control Sole-
noid Valve 4
(EDS 4)ONOFFONONONOFFONONONONONON
Line Pressure
Control Sole-
noid Valve 5
(EDS 5)OFFOFFONONOFFOFFONONOFFONONON
Line Pressure
Control Sole-
noid Valve 6
(EDS 6)ONOFFONONONOFFONONONONONON
Brake BAAAAAAAA
Brake CH
Brake DH
Clutch EAAAAAA
Brake FHHHHHHH
Lock–up
ClutchA
A = Applied
H = Holding
ON = The solenoid is energized.
OFF = The solenoid is de–energized.
** = Manual Second–Third gear is only available above approximately 100 km/h (62 mph).
*** = Manual First–Second gear is only available above approximately 60 km/h (37 mph).
Note : Manual First–Third gear is also possible at high vehicle speed as a safety feature.
DIAGNOSTIC TROUBLE CODE(DTC) P0734
GEAR 4 INCORRECT RATIO
Circuit Description
The TCM uses transaxle input speed information and out-
put speed sensor to control line pressure, TCC apply and
release and transaxle shift patterns. This information is
also uses to calculate the appropriate operating gear ra-
tios and TCC slippage. Conditions for Setting the DTC.
Conditions for Setting The DTC
S Time since TCM reset is greater than 500 msec.
S Time since shift end is greater than 500 msec.S Transmission oil temperature is greater than –10°C
(14°F).
S System voltage is greater than 9 volts.
S No input speed error DTCs P0715, P0716, and
P0717.
S Output speed is greater than 256 rpm.
S Input speed is greater than 400 rpm.
S No gear shift active.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 123
DAEWOO V–121 BL4
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
S High line pressure
Conditions for Clearing the MIL/DTCS The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S Check for intermittent input speed sensor or output
speed sensor circuit problems.
S Check for possible incorrect calibration.
DTC P0734 – Gear 4 Incorrect Ratio
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
2Visually inspect the transaxle cooling system for
fluid leaks.
Was condition found and corrected?–Go to Step 7Go to Step 3
3Has the transaxle fluid checking procedure been
performed?–Go to Step 4Go to Trans-
axle fluid check
procedures
41. Using the scan tool record each transaxle drive
range.
2. Drive the vehicle in transaxle gear ranges 1,2,3
and D with TP greater than 15% and vehicle
speed greater than 16km/h(10mph) for five
seconds.
Does commanded gear ratio match ranges as
shown?1st = 2.719
2nd = 1.487
3rd = 1.000
4th = 0.717Refer to Diag-
nostic AidsGo to Step 5
5Perform line pressure check.
Was the condition found and corrected?–Go to Step 7Go to Step 6
6Check for possible clutch slippage.
Was the condition found and corrected?–Go to Step 7–
71. After the repair, use a scan tool
clear info"
function and road test the vehicle.
2. Review the
DTC info".
Has the last test failed or is the current DTC dis-
played?Replace trans-
axle assemblyRepair verified
exit DTC chart