2004 DAEWOO LACETTI Ground

ENGINE CONTROLS 1F – 331
DAEWOO V–121 BL4
DTC P1610 – Main Relay High Voltage (1.6L DOHC)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Disconnect the main relay.
2. Measure the resistance between main relay
terminals 85 and 86.
Does the resistance within the specified value?75~85WGo to Step 3Go to Step 6
31. Turn the ignition switch to LOCK.
2. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 85 in the
relay harness connector.
Does the test light illuminate?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition switch to LOCK.
2. Disconnect the ECM wiring harness connector.
3. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 85 in the
relay harness connector.
Does the test light illuminate?–Go to Step 5Go to Step 7
5Repair a high voltage between the ECM wiring con-
nector terminal 7 and main relay terminal 85.
Is the repair complete?–Go to Step 7–
6Replace the main relay.
Is the replacement complete?–Go to Step 7–
71. Using the scan tool, clear the Diagnostic
Trouble Codes(DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 8Go to Step 2
8Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

1F – 332IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1611
MAIN RELAY LOW VOLTAGE (1.4L DOHC)
Circuit Description
When the ignition switch to ON, main relay will grounded
to ECM internal ground by ECM controlling.
A system voltage Diagnostic Trouble Code (DTC) will set
whenever the voltage is below a calibrated value.
Conditions for Setting the DTC
S The main relay circuit is a short to ground or an
open condition exists.
Action Taken When the DTCs Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC was set as Failure Records data
only.
S This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTCS A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.
If DTC P1611 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to set occurs. This may assist in diagnosing the
condition.

ENGINE CONTROLS 1F – 333
DAEWOO V–121 BL4
DTC P1611 – Main Relay Low Voltage (1.4L DOHC)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Disconnect the main relay.
2. Measure the resistance between main relay
terminals 85 and 86.
Does the resistance within the specified value?75~85WGo to Step 3Go to Step 6
31. Turn the ignition switch to LOCK.
2. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 85 in the
relay harness connector.
Does the test light illuminate?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition switch to LOCK.
2. Disconnect the ECM wiring harness connector.
3. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 85 in the
relay harness connector.
Does the test light illuminate?–Go to Step 5Go to Step 7
5Repair a high voltage between the ECM wiring con-
nector terminal 7 and main relay terminal 85.
Is the repair complete?–Go to Step 7–
6Replace the main relay.
Is the replacement complete?–Go to Step 7–
71. Using the scan tool, clear the Diagnostic
Trouble Codes(DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 8Go to Step 2
8Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

1F – 334IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1611
MAIN RELAY LOW VOLTAGE (1.6L DOHC)
Circuit Description
When the ignition switch to ON, main relay will grounded
to ECM internal ground by ECM controlling.
A system voltage Diagnostic Trouble Code (DTC) will set
whenever the voltage is below a calibrated value.
Conditions for Setting the DTC
S The main relay circuit is a short to ground or an
open condition exists.
Action Taken When the DTCs Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using the scan tool can clear DTC(s).
S Disconnecting the ECM battery feed for 10 sec-
onds.
Diagnostic Aids
Inspect harness connectors for backed–out terminals, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal–to–wire connection at
the ECM.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the A/C pressure display on the
scan tool while moving the connectors and wiring har-
nesses related to the ACP sensor. A change in the A/C
pressure display will indicate the location of the fault.
If DTC P1611 cannot be duplicated, reviewing the Fail Re-
cords vehicle mileage since the diagnostic test last failed
may help determine how often the condition that caused
the DTC to set occurs. This may assist in diagnosing the
condition.

ENGINE CONTROLS 1F – 335
DAEWOO V–121 BL4
DTC P1611 – Main Relay Low Voltage (1.6L DOHC)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Disconnect the main relay.
2. Measure the resistance between main relay
terminals 85 and 86.
Does the resistance within the specified value?75~85WGo to Step 3Go to Step 6
31. Turn the ignition switch to LOCK.
2. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 85 in the
relay harness connector.
Does the test light illuminate?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition switch to LOCK.
2. Disconnect the ECM wiring harness connector.
3. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 85 in the
relay harness connector.
Does the test light illuminate?–Go to Step 5Go to Step 7
5Repair a high voltage between the ECM wiring con-
nector terminal 7 and main relay terminal 85.
Is the repair complete?–Go to Step 7–
6Replace the main relay.
Is the replacement complete?–Go to Step 7–
71. Using the scan tool, clear the Diagnostic
Trouble Codes(DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 8Go to Step 2
8Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 341
DAEWOO V–121 BL4
DTC P1660 – Malfunction Indicator Lamp (MIL) High Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition switch to LOCK.
2. Disconnect the cluster wiring connector.
3. With the test light, connected to ground, probe
the ignition feed circuit, at terminal B6 in the
harness connector.
Does the resistance within the specified value?0WGo to Step 3Go to Step 6
31. Turn the ignition switch to LOCK.
2. With the test light, connected to ground, probe
the ignition feed circuit, at ECM wiring connec-
tor terminal 39.
Does the test light illuminate?–Go to Step 4–
41. Turn the ignition switch to LOCK.
2. Replace the cluster.
Is the replacement complete?–Go to Step 6–
5Repair a short to battery between the ECM wiring
connector terminal 39 and cluster wiring connector
terminal B6.
Is the repair complete?–Go to Step 6–
61. Using the scan tool, clear the Diagnostic
Trouble Codes(DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 7Go to Step 2
7Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 343
DAEWOO V–121 BL4
DTC P1661 – Malfunction Indicator Lamp (MIL) Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition switch to LOCK.
2. Disconnect the cluster wiring connector.
3. With the test light, connected to ground, probe
the ignition feed circuit, at terminal B6 in the
harness connector.
Does the resistance within the specified value?0WGo to Step 3Go to Step 6
31. Turn the ignition switch to LOCK.
2. With the test light, connected to ground, probe
the ignition feed circuit, at ECM wiring connec-
tor terminal 39.
Does the test light illuminate?–Go to Step 4–
41. Turn the ignition switch to LOCK.
2. Replace the cluster.
Is the replacement complete?–Go to Step 6–
5Repair a short to ground or open between the ECM
wiring connector terminal 39 and cluster wiring con-
nector terminal B6.
Is the repair complete?–Go to Step 6–
61. Using the scan tool, clear the Diagnostic
Trouble Codes(DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 7Go to Step 2
7Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
applicable DTC
tableSystem OK

1F – 350IENGINE CONTROLS
DAEWOO V–121 BL4
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step will determine if DTC P0107 is the result
of a hard failure or an intermittent condition.
3. Jumpering harness terminals 2 to 1 (signal circuit to
5 volts) will determine if the sensor is malfunction-
ing or if there is a problem with the ECM or wiring.6. The scan tool may not display 5 volts. The Impor-
tant thing is that the ECM recognizes the voltage as
more than 4 volts, indicating that the ECM and the
signal circuit are OK. A test light that illuminates
indicates a short to ground in the signal circuit.
7. A short to ground in the 5 volt reference circuit
could also set additional DTCs.
11. The replacement ECM must be programmed. Refer
to the latest Techline procedure for the ECM repro-
gramming.
DTC P0107 Manifold Absolute Pressure Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine.
3. Read the Manifold Absolute Pressure (MAP).
Does the scan tool display a MAP below the speci-
fied value?12 kPaGo to Step 3Go to Step 4
31. Turn the ignition switch OFF.
2. Disconnect the MAP sensor electrical connec-
tor.
3. Jumper the MAP signal circuit at terminal 2 to
the 5 volt reference circuit at terminal 1.
4. Turn the ignition switch ON.
Does the MAP read more than the specified value?96 kPaGo to Step 5Go to Step 6
41. Turn the ignition switch ON with the engine
OFF, review the Freeze Frame data, and note
the parameters.
2. Operate the vehicle within the freeze frame
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool display MAP below the specified
value?12 kPaGo to Step 3Go to
”Diagnostic
Aids”
5Inspect the MAP sensor harness electrical connec-
tor terminals for the following conditions:
S Poor connections.
S Proper contact tension.
S Poor terminal to wire connection.
Is a problem found?–Go to Step 8Go to Step 9
61. Turn the ignition switch OFF.
2. Remove the jumper wire.
3. Probe the MAP sensor signal circuit terminal 2
with a test light to B+.
4. Turn the ignition switch ON.
Does the scan tool read over the specified value?90 kPaGo to Step 7Go to Step 12
7Check the MAP sensor 5 volt reference circuit at ter-
minal 1 for an open or short to ground.
Is a problem found?–Go to Step 10Go to Step 11