2004 DACIA SUPERNOVA engine

19 - 12
19
COOLING - EX HA U ST - FU EL TANK
DISMOUNTING
The car is set on a two-column lifting stand.
The ba ttery is disconnected.
Th e co oling circuit is emptied at the filling stopper placed at the lower part of the radiator.
The fo llowing are taken apart.
- the distribution belt (see Chapter “ Distribution belt”) ;
- the ex tending pulley / runner (1);
- the fixing screws of the water-pump.
The water-pump is taken out at the upper end of the engine compartment.
SPECIAL DEVICES
MOT. 1202-02 Pincers for elastic collars
MOT. 1505 Device for measuring the belt tension
TIGHTENING COUPLES (daNm)
Screw-nut for extending pulley / runner 5
Screw for the crankshaft pulley 2+68
o+/-6o
Screws for right-side pendular stand 6.2
Screw-nut for hydro-elastic buffer 4.4
Screws for water-pump 2.2
Screw-nuts for water-pump 1
Screws for wheels 7.5
WATER PUMP
vnx.su

19 - 14
19
COOLING - EX HA U ST - FU EL TANK
DISMOUNTING - REMOUNTING EXHAUST
The catalytic converter, when in operation, reaches high tempera-
tures, and consequently m ust not co me in touch with flammable materials, which
would lead to self-combustion. The catalytic converter will be kept out of mechanic shocks.
D
IS M O UNT ING
In order to take apart t he noise-damper system 1, the following opera tions a re to be
performed: The screw-nuts 2 of the fixing collar, between holder 3 and noise-damper 1, are
loosened; The two elastic fixing stands of the damper are taken apart , at the back on the car
bodywork; The noise-da mper system is pulled and taken out.
In order to take apart the assembled holder 4, the following operations are to be performed:
Collar 4 is taken off and the assembled holder is disconnected from the catalytic
converter;
The elastic stands of the assembled holder are taken off;
The scre w-nuts of the fixing collar 2 are loosened and t he a ssembled holder is
taken out by gently rot ating, and pulling it towards the front.
In order to take apart the catalytic convert er system 6, the following opera tions are to
be performed:
The engine shield is taken apart ;
The two screw-nuts 7 for the fixation of the engine shield on the two stud-bolts on
the exhaust gallery flange;
The fixing screws of converter stand 5 are taken off;
The oxygen probe is taken apart;
Collar 4 is taken apart, and t he c atalytic converter assembled on the assembled
holder is disconnected; The catalytic convert er is taken out.
R
EMONTARE
The mounting opera tions are performed in the re verse order.
Make sure there perfect watertightness between the elements of the exhaust system,
by using the Wurth watert ightening paste, along the (i nner part of the) joining stretch,
between the gas expansion chamber and the catalytic convert er ( 0.014 kg), and between
the noise-da mper a nd the expansion chamber ( 0.013 kg);
The fittings of the oxygen probe will be replaced for each taking-apart operation;
The tightening couple between the damper and the holder: 3.5 daNm +/-0.5.
vnx.su

19 - 16
19
COOLING - EX HA U ST - FU EL TANK
IMPORTANT
Duri ng the interventions affecting t he
petrol tank and the fuel supply circuit one
must not smoke or bring incandescent
parts near the work-place.
The emptyi ng of the tank does not require
taki ng apart the tank. Ac ces s is allowed
through the inside of the car (i.e. the boot). To take apart:-the carpet of the boot;
-t he lid of the visiting mouth (by taking
off th e four screws);
-the c lick-collar 1 is ta ken out by means
of the MOT 1202 device;
-a t ube is adapted to the A outlet, which
should be long enough to be introduced into a
ve ssel outside the car. The
H relay of the petrol-pump is taken out of
the fuse box located in the engine compartment,
and term inals 3 and 5 of the re lay connector are
shunted, thus ensuring the operation of the petrol
pump ( 12 V).
Th e operation of the pump will be stopped
when an intermittent leakage of the petrol is no-
ticed. The shun t is taken off.
The relay is mounted.
EMPTYING OF TANK
vnx.su

20
CLUTCH
IDENTIFICATION
TYPE OF TYPE OF MECHANISM DISC
VEHICLE ENGINE
Supe RNova E7J
E215 CP OE 3500
26 groves
V = green
G = grayM = violet
D
= 215 mm
E = 7 mm
20 - 2
vnx.su

20
CLUTCH
The complete return
of the clut ch pedal is
checked
The state of the
hydrau lic circuit is
checked
The worn-out or oiled
clutch is checked
- The worn-out elements are
replaced
- The cause of the leakage is
e liminated.
The st at e of the
pedal is checked


The state of the clutch
m echanism is checked,
and it is replaced if
nece ssary


Clutch skidding
The engine has the ten-
dency to accelerate
NECONFORMING
NON-CONFORMING
The faulty parts are
replaced
CONFORMING
CONFORMING
CONFORMING
D I A G N O STIC
20 - 5


vnx.su

20
CLUTCH
Trepidation
(t he car starts “by fits”)
The sta te of the props
of the gearbox is checked
Oiled clutch, or clutch hav-
ing a beat
The fau lty parts are replaced.
The o rigin of the beat is elimi-
nated.
The pr ops are replaced and the tight-
ening of the gearbox fixing spots on
the engine is checked, and also the
fixing of the engine
Clutch pedal has a “creak”
The axis of the clutch
pedal is oiled
Pedal axis worn-out
The fau lty parts are replaced
NON-CONFORMING



NON-
CONFORMING

CONFORMING



D I A G N O STIC
20 - 8
vnx.su

20
CLUTCH
CLUTCH DISC MECHANISM
REPLACEMENT
This operation is done after taking apart the engine - gearbox ensemble and after
their separation.
The stopping sector MOT 582 is mounted.
The screws fixi ng th e mechan ism are taken off.
The mechan ism and the clutch disc are taken apart.
Visual inspection is done: - wear of engi ne flywheel;
- co ndition of the starter crown;
- watertightness at the level of the crankshaft fitting;
- co ndition of the flywheel surface (it must not have scratches).
The fau lty parts are replaced and the grooves of the clutch shaft are cleaned.
SPECIAL DEVICES
MOT 582 Flywheel immobilizing sector
AMB 1518 Clutch centering device
TIGHTENING COUPLES (daNm)
Clutch mechanism screws 2
20 - 9
vnx.su

CV JH3 - 05021
MANUAL GEARBOX
21 - 3
TIGHTENING MOMENTS
DESCRIPTION
A
ttachment screws of the mechanism crankcase on the clutch –
di fferential case
S econdary shaft screw
Primary shaft nut
Back cap fixing screws
Oil draining plug
R everse driving contact
S crews for fixing the bellows – left transmission cap assembly
Screws for fixing gearbox on engine case (M10 – 90)
Screws for fixing gearbox on engine case (M10 – 35)
S crews for fixing gearbox on engine
LOCTOU fixing screw
Screws for fixing the RPM sensor on the clutch c ase
S crews for fixing the control axle assembly
S crews for fixing hydraulic receiver on clutch case MOMENT
(daNm)
2,57
19
2,5
2,5
2,5
2,5
4,4
2,1
4,4
0,5
0,8 2
2,1
vnx.su