2004 DACIA SUPERNOVA key

82A
HORN - ENGINE IMMOBILISER
82A - 6
Af
ter ordering a new key head based on the alphanumeric code mentioned on the i nvoice,
dismount the old key head and remove the metal insertion (mechanical part), then introduce the
old metal insertion in the new key head according to t he previously mentioned procedure. In
case the key head is provided with RF remote control for blocking/ unlocking the doors, after its
replacement, perform the synchronising procedure of the RF remote control with the decoder,
subject to the following cases:
(a)- the vehicle has a key with RF remote control and one without RF remote control; in this
case after the replacement of the RF key, perform the “simple synchronised procedure” in order
to bring into phase the RF remote control with the decoder.
( b)- the vehicle has two keys with RF remote control; after the replacement of one RF key,
perform the “specific synchronised procedure”;
(c)- the vehicle has two keys with RF remote control; if both keys are replaced, perform the
“simple s ynchronised procedure for the firs key and the “specific synchronised procedure” for
the second one. If a key was lost, a new key head and a metal insertion will be ordered. KEY HEAD REPLACEMENT
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 7
A
ll the new decoders, are not coded. After t he mounting on the vehicle it is necessary the
memori sation of t he key head code by the decoder i n order to be operational. If only the
decoder is replaced, no intervention is necessary to the injection computer, which will keep the
old anti starting code. When the vehicle is provided with RF remote control for blocking/unlocking
the doors, the performing of the resynchronisation of the keys with the decoder is imposed, after
its mounting.
If further to the diagnostic of the anti starting system, using the CLIP tester, the replacement of
the decoder is imposed, proceed as follows: - disconnect the front wiring connector from the E.C.U. decoder ( the contact being off);
- dismount the attachment screws of the E. C. U. decoder on the front left pillar;
- mount the new E.C.U. decoder;
- connect the front wiring to the new decoder.
Proceed then to the insertion of the anti starting code using the contact key, then to its memorising
(validation) in the E.C.U. decoder, using the CLIP tester. For this purpose, perform the “E.C.U.
decoder re placement procedure and a nti starting c ode memorising”. Che ck then the correct
operation of the anti starting system with both keys. E.C.U. DECODER REPLACEMENT
AT TENT ION
Once the decoder has memorised the key codes, this code cannot be erased
or replaced with another one.
If it is necessary the replacement of the kit (E.C.U. decoder and two key heads), after that
realise t he “ Kit replacement procedure”.
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 9
The RF remote control has no influence on anti starting system. It has only the function of
blocking/ unlocking the doors. The RF remote control with evolutionary code can use only two
keys as the decoder may manage only two different evolutionary codes. The key heads have an identification number formed by 8 alphanumeric characters (letters
and figures) , beginning with letter E.
In case of loosing one key, a key head and a metal insert ion will be ordered, then the
resynchronisation procedure of the RF remote control of t he ke y with t he decoder from the
vehicle must be performed. If the vehicle is provided with RF remote control key and this one
has been replaced, then perform the “ Simple synchronised procedure “. When the vehicle has
both keys with RF remote control, then perform the “Specific synchronised procedure “ after the
replacement of the second key.
NOTE - In the case only one ke y head is replaced, usually there is no need for
r esynchronisation of the other RF remote control.
- If both RF remote controls are desynchronised, one procedure of resynchronisation
will be performed with each remote control: perform the “Simple synchronisation
procedure for the first RF remote control” and the “Specific synchronisation procedure”
for the second RF remote control. Check then t he operation of blocking/ unlocking of the doors with both RF remote
controls. RF REMOTE CONTROL FOR BLOCKING/ UNLOCLING
THE DOORS
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 11
A.
ECU DECODER REPLACEMENT PROCEDURE AND ANTI STARTING
CODE MEMORISING
The new E.C.U. decoder is always not coded. After its mounting on the vehicle it is necessary
that this one is memorising the anti starting code in order to be operational.
NOTE
If only the E.C.U. decoder i s replaced, there i s no need of an i ntervention to t he
E.C.U. injection (injection computer), which will keep the old anti starting code.
AT TENT ION
After the E.C.U. de coder memorised the anti starting c ode, this code cannot be erased
or replaced with another one.
In order t o perform this procedure, one of the keys of t he ve hicle and the CLIP tester are
needed. Perform as follows: 1. Connect the CLIP tester to the diagnostic socket and to the battery (or the lighter
socket) of the vehicle. 2. Read the configuration of the old E.C.U. decoder in the following way, before dismounting
it from the vehicle:
- select t he type “SUPERNOVA” and the “050” equipping level;
- enter the menu “ COMPUTER TEST” then choose “ ANTI STARTING”
- access “COMMAND MODE” then “CONFIGURATIONS READING”
- note the configurations found : petrol/d iesel, programming with 1 or 2 keys, ceiling delay,
the type of the doors’ blocking switch (CPE), etc.;
3. Get back to the m enu “TEST COMPUTERS”
4. Remove the old E .C.U. decoder and replace it with a new one, the contact being off.
5. Enter the menu “ANTI STARTING”, then select “ STATE LIST”. If the E.C.U. decoder
is new, you must find the following states:
18G FIRST CYCLE MEMORISING………………........................ ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………….. ACTIVE
19D UNLOCKED KEY PROGRAMMING………………............. ACTIVE
OBSERVAT ION
If the states 19G and 19D are not “ACTIVE” this means the E.C.U. decoder has
been already used, so it isn’t new and cannot memorise another anti starting code.
Access the menu “COMMAND MODE” and then “CONFIGURA TION”, where you will
configure the new E.C.U. decoder in the same way as the old one: petrol, 1 key, ceiling delay,
impulsion doors blocking switch, etc. selecting one by one these configurations, which you’ll
validate with “CLICK” on the blue button on right top of the screen. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 12
7. Get back to “ TEST COMPUTERS”
8. Set the contact on for 2 seconds in “ M” position, without start ing the engine. T he a nti
starting indicator will begin to blink rapidly.
9. Access the menu “ STATE LIST”, where the following states must exist:
9D RECEIVED KEY CODE…………………………………………ACTIVE
19G NOT PERFORMED KEY PROGRAMMING…………………PASSIVE
10. Take t he contact off. In the menu “COMMAND MODE” select “ACTUATORS”, then
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear, followed
by “ FINISHED COMMAND”.
11 . The anti starting indicator will blink rarely.
12. Get back to the “STAT E LIST”, which now, must be like that:
18G FIRST CYCLE MEMORISING ………………………………ACTIVE
19G NOT PERFORMED KEY PROGRAMMING... ………………PASSIVE
19D UNLOCKED KEY PROGRAMMING………………………. PASSIVE
13. Set the contact in “ M” position for 2-3 seconds i n order t o send the code to t he E .C.U.
injection. The anti starting indicator must light for 3 seconds, then turn off.
14. Take off the contact. After 10 seconds, the anti starting indicator will blink rarely.
15. Check the engine starting with both keys, and then take the contact off.
16. Check in the menu “ STATE LIST ” if the state 10G “ANTI START ING” is “ACTIVE”.
Pe rform the synchronisation of the TRF remote control with the decoder (with 1 or 22 keys).
OBSERVAT ION
With the CLIP tester, a starting interdiction may be simulated, proceeding as follows: -take the c ontact off; wait for 10 seconds, then the anti starting indicator will
blink; -in the m enu “COMMAND MODE” access “ ACTUATORS” then validate “
FORCED PROTECTION MODE” launching the command from the bl ue button
s ituated on the right topside of the screen. “COMMAND IN PROGRESS” will be
displayed and then “FINISHED COMMAND”.
-in the menu “STATE LIST” search for the state 10G ”ANTI STARTING”,
which must be “ ACT IVE”;
-set the contact on “M” position; the anti starting indicator will blink rapidly,
and the engine starting is i mpossible; - remove the key from the contact and check then the engine starting with both
keys, so the procedure is finished. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 13
NOTE
For the RF remote control synchronisation, after the replacement of an E.C.U.
decoder, the synchronisation procedure must be performed taking into account the
following situations: -for one RF re m ot e c ont ro l , pe rf orm t he “ SIMP L E SY NC H RONIS ED
PRO CEDURE”;
-f or the second RF remote control perform the “SPECIFIC SYNCHRONISED
PRO CEDURE”.
B. KIT REPLACEMENT PROCEDURE(E.C.U. decoder plus 2 key he ads)
In case of one kit replacement perform the following steps:
- memorising the anti starting code by the E.C.U. decoder
- memorising of the new anti starting code by the injection computer; i t is necessary the
repairing code (found out based on the old ke y heads code) and t he CLIP tester.
Perform the actions in the following sequence:
1. Mount the metal insertions of the old keys to the new key heads.
2. Send to Tech Line the key heads code, written on the vehicle invoice, in order to get the
repairing code. 3. Connect the CLIP tester to the diagnostic socket and to the battery (or t o the lighter
socket) of the vehicle. Read the configuration of the old E.C.U. decoder before dismounting off
the vehicle, as follows: - select vehicle type “SUPERNOVA” and the “050” equipping level;
- enter the menu “ COMPUTER TEST” then choose “ ANTI STARTING”;
- access “COMMAND MODE” then “READ CONFIGURATIONS”;
- note the configurations : petrol/diesel, programming with 1 or 2 keys, ceiling delay, the
type of the doors’ blocking switch (CPE), etc.;
4. Get back to the m enu “ANTI STARTING”;
5. Dismount the old E.C.U. decoder and replace it with a new one, the contact being off.
6. Check the configuration of the new E.C.U. decoder selecting “ STATE LIST”; here you
must find the following states: 18G FIRST CYCLE MEMORISINGPASSIVE…………………INACTIVE
19G NOT PERFORMED KEY PROGRAMMING ……………….ACTIVE
19D UNLOCKED KEY PROGRAMMING ………………………ACTIVE
NOTE
If the state 19G and 19D are not “ACTIVE” this m eans the E.C.U. decoder isn’t a
n ew one and cannot memorise another anti starting c ode. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 14
7. Set the contact in “M” position with one of the keys (without starting the engine), for about
2 seconds and then check the following states, which must be:
9D RECEIVED KEY CODE………………………………………. ACTIVE
19G NOT PERFORMED KEY PROGRAMMING ……………… ACTIVE
8. Set the contact with the second key (without starting the engine) for about 2 seconds.
Check then the following states:
-case (a)- the second key belongs to the vehicle;9D RECEIVED KEY CODE………………………………………. ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………… PASSIVE
- case (b)- the second key does not belong to the vehicle or the first key was used once again;
9D RECEIVED KEY CODE………………………………………PASSIVE
19G NOT PERFORMED KEY PROGRAMMING……………… ACTIVE
9. The anti starting indicator blinks rapidly.
10. Take off the contact. In t he menu “COMMAND MODE” select “ACTUATORS” and
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear,
followed by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Get back to the “ STAT E LIST”, which now must be as follows: 18G FIRST CYCLE MEMORISING……………………………... ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………… PASSIVE
19D UNLOCKED KEY PROGRAMMING………………………PASSIVE
13. In the m enu “COMMAND MODE” choose “ ACTUATORS”. Select the command “
FORCED PROTECTION MODE” launching the command from the blue button situated on
the ri ght topside of the screen. The display will show “COMMAND IN PROGRESS” and
then “FINISHED COMMAND”. Get back to t he “STATE LIST “ and check the state:
9G FORCED PROTECTION MODE …………………………….. ACTIVE
14. Set the contact on “M” position. The anti starting indicator will start to blink rapidly. Check
in the “ STATE LIST” if the state “ANTI STARTING” is “ACTIVE”.
15. In the menu “COMMAND MODE” access “ACTUA TORS”, then select the command “
MANUAL INTRODUCTI ON CODE”. Type the four figures of the repairing code, then validate
with the key “ENTER”. On the screen the message “COMMAND IN PROGRESS” will
appear and then “FINISHED COMMAND”. 16. Take off and then set again the contact, without starting the engine, in order to send the
new anti starting code to the injection computer. The anti starting indicator will light for 3 seconds,
and then it will turn off.
17. The procedure is finished. Check the engine starting with both keys. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 15
NOTE
For the RF remote control synchronisation, after the replacement of a kit, take into
account the fol lowing situations: - for the first RF remote control, perform the “ simple synchronised procedure”;
- for the second RF remote c ontrol perform the “specific synchronised procedure” .
C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by the means of the CLIP tester. This is possible
only if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed
by the state: 10G ANTI STARTING…………………………………………….. ACTIVE
After getting from DACIA database the repairing code (based on the code from the vehicle’s
key head), perform the following operations. 1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle. 2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “SUPERNOVA” and “050” equipping level.
5. Select the menu “ COMPUTER TEST” then choose “ ANTI STARTING”.
6. In the menu “ STAT E L IST” find t he state 10G “ANTI STARTING” which m ust be
“ACTIVE”.
7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL INTRODUCTION CODE” where you will write the
repairing code (formed of four figures), then validate it with the key “ENTER”. T he message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”.
9. Now the procedure is finished and you may start the vehicle engine.
AT TENT ION
You may perform three essays of introducing the repairing code; if aft er the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then put it
again, other t hree essays being allowed.
NOTE
This procedure does not decode the injection computer, but allows only the start of
the vehicle’s engine. After ten minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced. PROCEDURES
vnx.su