2004 DACIA SUPERNOVA heating

40
GENERAL
40 - 5
The replacement (repara tion) operations of t he weldable elements descri bed i n t his
chapter a re specified subject to: cutting out of t he parts t o be replaced; the a ccess to the
welded elements, tools and checking devices accessibility, etc.
In case the vehicle body has suffered import ant deform ations it is recommended the
str aightening of t he damaged body elements, by means of some hydraulic pre sses, the
operation being performed slowly and at cold. For this range of vehicles, the e lements re sistance structure which a re a ffecting the
vehicle securi ty, are not to be partially re placed ( not to be cut), but entirely.
After welding detaching, the body elements must remain stra ight, without breakage or
cracks, the possible holes being covere d out with filling material or by tinning. The body
elements surfaces are t o be pickled ( to eliminate possible oxidation marks) , dried and
initially applied a paint layer. The electric welding detaching of the body elements, is performed as follows:
- with a well sharpen chisel, this method may lead to part s deformation or even
parts breaking.
- by using some extractors equipped with steel cutter type Bre ndeo or Pickvant
max. 6 mm, having the cutting head as per shape shown in pict.1.
1. Centeri ng point
2. Sharpen slope
3. Drill acting edges
4. Gap for catching the welding materialP = aprox. 0.4 mm
Whatever method is used, the remaining element m ust be in good order a nd to allow
performing of a good quality welding point.
The pl ates cutting it is recommended t o be pe rformed ( subject of importance and thick-
ness ) using manual scissors or pneumatic portable tools for plates cutting.
Du ring cutting or welding of the body elements it is necessary to protect the electric
wir ing from the interi or of the body structure.
The cutting, welding, or strengthening operation done on body welded elements, are to
be performed on body checking/ straightening bench type CELETTE .
IMP ORTANT
When removing or straightening the body resistance e lements i t i s forbidden t he
total or partial heating, in order to avoid the mechanical resistance and metal elasticity
decreasing. REPAIRIN
G GENERAL CONDITIONS
vnx.su

Mechanisms and accesoires5
Climatisation6
Garnishing and tack room7
Electr ic equipment8
57 LOWER INTERNAL ACCESSORIESDashboard..................................................... 57-1
Dashboard upper part ................................... 57-3
Central console............................................. 56-4
Documents compartment.............................. 57-5
Ste ering whee l axle hal f-cases...................... 57-6
Inside rear view mirror.................................. 57-7
S un visors...................................................... 57-8
Turning handles............................................ 57-9
Handbrake case............................................. 57-10
59 SAFETY ELEMENTS Front safety belts........................................... 59-1
Re ar safety belts............................................ 59-2
61 HEATING Climat e control asse mbly.............................. 61-1
Housing manifold.......................................... 61-2
Heating radiator............................................. 61-3
C limat e control blower.................................. 61-4
Diagnosis....................................................... 61-5
62 AIR CONDITIONING Generalities.................................................. 62-1
AC unit operating diagram........................... 62-4
Evaporator.................................................... 62-5
Comp ressor................................................... 62-7
Condenser..................................................... 62-8
Pr essure controller........................................ 62-9
Dryer filter tank............................................ 62-10
Unit piping.................................................... 62-11
C limat e control unit...................................... 62-12
Diagnosis....................................................... 62-13
65 SEALING OPENING ELEMENTS Carriage body se aling................................... 65-1
66 SEALING WINDOWS AND SCREENS Glasses sealing............................................. 66-1
Insi de wipers ............................................... 66-2
Outside wipers.............................................. 66-3
71 INTERNAL BODY TRIM Carriage body coverings.............................. 71-1
Fr ont door threshold covering...................... 71-2
Upper front pillar covering........................... 71-3
Re ar door threshold covering....................... 71-4
Mi ddle pillar covering.................................. 71-5
Re ar passa ge covering.................................. 71-6
Re ar wheel passage covering........................ 71-7
Mi ddle pillar lower covering........................ 71-8
Re ar side panel covering............................... 71-9
R oof gasket .................................................... 71-10 Carpets
......................................................... 71-11
Cowl panel noise absorbent ......................... 71-12
72 SIDE OPENING ELEMENTS TRIM Front door panel........................................... 72-1
Re ar door panel............................................ 72-2
74 BACK SEAT TABLES AND PARCEL SHELVES Upper back panel replacement...................... 74-1
75 FRONT SEATS FRAMES AND RUNNERS Front seats.................................................... 75-1
Fr ont seat slides guides................................ 75-2
Fr ont seat armature...................................... 75-3
76 REAR SEATS FRAMES AND RUNNERS Rear bench................................................... 76-1
B ench seats .................................................. 76-2
77 FRONT SEAT TRIM Seats upholstery dismounting...................... 77-1
Back rest upholstery dismounting................ 77-2
78 REAR SEAT TRIM Seats upholstery dismounting...................... 78-1
Back rest upholstery dismounting................ 78-2
80 BATTERY - FRONT HEADLIGHTS Battery... ...................................................... 80-1
Head lamp asse mb ly..................................... 80-4
F og lamps.................................................... 80-5
Bulbs r eplacement....................................... 80-6
Headlamps adjustment................................. 80-7
81 REAR AND INTERIOR LIGHTING Bulbs r eplacement........................................ 81-1
Bulbs ............................................................ 81-2
Diagnostic.................................................... 81-3
Cockpit fuse box.......................................... 81-6
82A HORN - ENGINE IMMOBILISER Gene ralities.................................................. 82A-1
Key head repla ceme nt.................................. 82A-6
E.C.U. decoder repla ceme nt........................ 82A-7
Antistarting bushing replaceme nt................ 82A-8
RF remote control for blocking/unlocking
t he doors...................................................... 82A-9
Electric control unit injection repla cement... 82A-10
Pr ocedures.................................................... 82A-11
Diagnostic..................................................... 82A-17
vnx.su

HEATING
61
61 - 1
DISMOUNTING
Disconnect the battery.
Dismount
the documents compartment.
Di smount the attachment c lip of the mixing flow flap control cable, (8) (from the c limate
control unit). Remove the right aeration grill (from the right side of the central console).
Dismount the attachment clip of the distribution flow flap control cable, (7)(from the climate
control unit). Dismount the attachment metal screws (5 ) of the climate control assembly (6 ) on the central
console of the dashboard. Remove the climate control assembly from its seat.
Disconnect the connection box of the climate control switch.
Disconnect the connection box of the instrument panel lighting.
Dismo unt the attachment clip of the recycling flow flap control cable (9) and remove it from its seat.
Remove: the mixing flow flap control cable (8 ) from the heating control button (2 ) and the
distribution flow flap control cable (7) from the distribution control button (3), by releasing the
clips attachment screws.
Remove the climate control switch (4) out of its seat by detaching from clips.
Dismount the four lighting bulbs.
REMOUNTING
Pe rform in the reverse order the dismounting operations, taking into account the following
recommendations: - the flow flaps c ontrol cables are first fixed to the board with the jacket, in axial contact
with the limiting support and then pass the panel button and the similar flow flap on the
corresponding position, then clamp the cable to the unit support; - check if the levers from the climate unit and from the distribution box, have the adequate
strokes t o ensure the close-opening of the flow flaps; - if yes, mount the assembly (6 ) on the central console, the documents compartment and
the aeration grill ;
- if not, set the sleeve l ength of each control cable to the mounting bracket of the climate
unit and the distribution box.
- the maximum moment for the full flow flaps opening is 1,9 Nm.
CLI
MATE CONTROL ASSEMBLY
9
8
7
6
1
2
3
4
5
vnx.su

HEATING
61
61 - 2
DISMOUNTING
Disconnect the battery.
Drain the cooling system.
Dismount the attachment
collar of the hoses
on the heating radiator. Clog the hoses of the he ating radiator by
means of the device MOT 453.
Dismount the documents compartment.
Dismount the central console.
Dismount the control climate control.
Disconnect the airflow pipes from the climate
control unit. Dismount the nuts and the attachment screws
of the climate control unit from the carriage body.
Release the climate control unit.
REMOUNTING
Perform in the reverse order the dismounting operations.
HOUSING MANIFOLD
vnx.su

HEATING
61
61 - 3
HEATING RADIATOR
R
EMONTARE
Se efectueazã în ordine inversã opera
iei de demontare.
În cazul deteriorãrii garniturilor, ele se vor înlocui. DISMOUNTING
Disconnect the climate control unit.
Dismount the attachment clips and release the
left- right cases.
Release the heating radiator.
vnx.su

HEATING
61
61 - 4
DISMOUNTING
Release
the climate maintenance assembly from under the dashboard, dismounting beforehand
the central console, the documents compartment, the lower casing, the dashboard. Unscrew the attachment screws of the turbine deflector.
Unscrew the attachment screws of the blower.
Disconnect the blower from the blower wiring.
REMOUNTING
Perform in the reverse order the dismounting operations.
C
LIMATE CONTROL BLOWER
vnx.su

HEATING
61
61 - 5
CLI
MATE CONTROL BLOWER DOES NOT WORKING
Check fuse F 01.
F01 good. Check F09.
F09 good. Check blower supply.
F01 blown. Replace the fuse.
The blower is not supplied.
Check R2 relay. The blower is supplied.
Check the air conditioning switch.
Relay R2 is damaged.
Replace the relay.The relay is not da
maged.
Broken or disconnected
relay switch wiring. Good switch.
Ma
ss wire
disconnected or brok en.Damaged switch.
Replace the switch.
DIAGNOSIS
vnx.su

89A
ELECTRICAL DIAGRAMS
89A - 22
The fuse box placed in the engine compartment is attached in front of the left shock absorber
column and contains relays and fusible protecting the following electric circuits:
A.
for equipping E1, E2
( until 01.06.2001)
RELAY
RELAY TYPE
CONTROLLED
CIRCUIT
A
15A
Fog
headlamps
D
30A
Injector s, canister purging valve,
oxygen sensor heating
resistance, injection computer.
H
30A
F uel pump
Ignition coil
C
30A
C ooling blower
(vehicle without
AC)
FUSE
NUMB ER
F01
F02
F03
F04
F17 FUSE
TYPE
30A
25A
7,5A 5A
15A PROTECTED C IRCUIT
In jectors, oxygen sensor resistance heating, canister
purging valve, injection computer, fuel pump, ignition coil.
Cooling blower ( vehicles without AC)
Injection computer ( + DC)
In jection computer( (+IC)
Fog headlights
FUSE BOX FROM ENGINE COMPARTMENT
vnx.su