2004 DACIA SUPERNOVA air filter

E7J-A-2/60 ENGINE13
PUMP SUPPLY
SU PPLY PRESSURE CONTROL
SPECIAL DE V I C E S
MOT 1311-01 Control Kit for
petrol pressure
MOT 1311-04 J Junction
MOT 1311-06 Junction-disconnect
ing device
CAUTION!
When the fuel circuit is opened, any
petrol jet due to residue pressure must be
averted by means of a gauze.
The air-filter is taken apart .
The fuel supply hose is disconnected.
The MOT 1311-04 deri vation junction
is connected onto the ramp, then the fue l-
s upply channelling is re-connected onto the
junction.
Te rm inals no. 3 and 5 of the H fuel-pump
relay (l ocated in the engine fuse -box) a re
shunted.
Pressure must be 3+/-0.2 bar.
By applying a 500 mbar depression on
the pressure-regulator, the pre ssure of the
fuel must be 2.5+/-0.2 bar.
13 - 5
MOT. 1 311 -0 4 MOT. 1 311 -0 1
The manometer 0-10 bar, as well a s the
flexible hose MOT 1311-01 are mounted.
SU PPLY PRESSURE
MOT. 1 311 -0 6
vnx.su

16E7J-A-2/60 ENGINE
16 - 4
ST ARTING AND CHARGING
SPECIAL DEVICES
MOT 1505BELT TENSION MEASURIN G DEVICE
DIS M O UNT ING
The car is set on a two-column lifting stand;
Disconnect the electric connections from the battery.
The fuel supply conduit is uncoupled;
The following are taken off: - air filter;
- the oil-gauge tube;
- the top scre w of the alternator;
- the alterna tor belt;
- the stretching fl ange of the alternator.
The car is suspended.
The electric connectors of the alternator are uncoupled;
Di smount the alternator l ower attachment screw.
Lower the vehicle.
The alterna tor is taken out at the top.
AL TERNATOR
R
E-MOUNTING
The mounting opera tions are done in the reverse orde r;
The carrying belt of t he alternator is stretched to get the re commended ( 263
Hz+/- 10% ) mounting voltage;
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 4
PLAC ING OF ELEMENTS
1.Can
ister-draining valve;
2. Air -filter;
3. Det onation sensor (tightening couple: 2.5 daNm);
4. Atmo spheric air-pressure sensor;
5. Step-by -step idle mode-adjustment engine;
6. Cla pper position potentiometer;
7. Air- temperature sensor;
8. Inje ction calcul ator;
9. Shock-s ensor;
10. Fuse-and- relay box;
11. Revolution sensor;
12. Water- temperature sensor;
13. Oxyg en sensor (tightening couple: 4.5 daNm);
14. Igniti on coil;
15. Carbon canister.
1 14 3 5 6 7 4 2 11
9
10
15 13 \
12 8
PLACING OF ELEMENTS
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 47
DIAG
NOSING-INTERPRETING THE DEFECTS
POLLUTING COMBUSTION MISFIRE
DESTRUCTIVE COMBUSTION MISFIRE
1. Combustion misfire during the last running done
2. Confirmed combustion misfire.DEFECT
PR ESENT
Combustion misfire at cylinder 1
Combustion misfire at cylinder 2
Combustion misfire at cylinder 3
Combustion misfire at cylinder 4.
Furnishe s informa tion c onc e rning the na ture and loc ation of bre a kdown.
SUGGESTIONS
31.
Connect the tester and select “Test of ignition”.
Watch the indications and replace the necessary parts.
Connect the tester and select “Test of compression”.
Watch the indications and replace the necessary parts.
Connect the tester and check the cogs of the flywheel.
Remedy if necessary.
If no defect is found ou
t, then there is a problem with the fuel-supply circuit. You must
check:
-p etro l filter
-f low and pressure of fuel
-condition of petrol pump
- if there are impurities inside the tank
-condition of injectors.
Remedy the elements of the fuel-supply circuit that are faulty.
Note down other functional defects.
Erase the defec ts memorized by the calculator.
Remedy other possible defects.
AFTER REPAIR
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 63
DIAG
NOSING-INTERPRETING THE STATES
PARAM ETERDETONATION SIGNAL
SUGGESTIONSNo defect should be present or memorized
The de tonation sensor should generate a signal, the amplitude of which must differ from 0,
a proof of the fact that it perceives the mechanical vibrations of the engine.
If th e signal = 0:
- check if the sensor is well fixed
- ch eck the insulation and continuity of cabling along the circuits:
pin 20 of calculator
♦ pin 1 of detonation sensor
pin 79 of calculator
♦ pin 2 of detonation sensor
pin 19 of calculator
♦ pin 1 of detonation sensor screening.
Replace detonation sensor if necessary.
AFTER REPAIR
PA R A M E T E RADAPTATION OF ENRICHMENT WHILE RUNNING
ADAPTATION OF ENRICHMENT IN IDLE MODE
SUGGESTIONS No defect should be present or memorized.
Do initialization.
Ma
ke sure the canister draining valve is watertight.
Erase memo ry o f th e injection calculator.
With the engine hot, in the stage of the idle mode adjustment, watch these parameters and
notice:
- if one of the parameters drifts to the MAX limit, then there is no enough petrol
- if one of the parameters drifts to the MIN limit, then there is too much petrol.
Ensure the cleanness and the good functioning of:
- p etrol filter
- petr ol pump
- petrol supply circuit
- petr ol tank.
AFTER REPAIR Perform again the conformity test.
Perform again the conformity test
vnx.su

E7J-A-2/60 ENGINE17
IGNITION AND INJECTION
17 - 69
DIAG
NOSING-BREAKDOWN LOCALIZATION ALGORITHM
RUNNING PROBLEMS3.
SUGGESTIONSDo not use this information before having done the complete
check- up with the tester!
Check if there are no broken tubes
Check if the air filter is not deformed.
Check the condition of the fittings.
Check if the exhaust collector is watertight.
Make sure that, after taking them off, the injectors do not leak.
♦
♦
♦
Check if there are no broken tubes
Check the state of the sparking plugs and the ignition coil.
Check if there is petrol in the fuel tank (do not rely on the
on-board in dices). Check if it is the fuel recommended by
the manufa cturer. Check if there are no broken tubes.
Check if the exhaust circuit is not strangled-up and the
cata lyst is not stopped-up.Check the exhaust
system
♦♦
♦ ♦
♦ ♦ ♦Check, on the oil gauge, if the level of the oil is not too high.
Check the air filter
Ch eck the fuel
Check the tube s a nd
hose s.
Check the fuel-sup-
ply circuit
Check the ignition Check the engine oil
levelCheck the intake
collector
Check the exhaust
collector
Check the injectors
A
vnx.su

MECHAN ICAL ELEMENTS CONTROL
37
MASTER VAC 7 SERVO M ECHANISM
The ” Master-Vac 7” servobrake is a brake booster with the objective of reducing the driver
effort on the brake pedal.
AT TENT ION
The servobrake cannot be repaired.
The only items of the servobrake which are to be replaced are the air filter and the retainer
valve.
DISMOUNTING
Close the pipe between the brake fluid reservoir and the clutch transmitter cylinder by means
of the MOT 453 device.
Drain the liquid out of the reservoir.
Disconnect from the reservoir the feeding pipe of the clutch transmitter cylinder. SERVOBRAKE
OBSERVAT ION
In case one circuit is damaged, the pedal stroke shall be longer, the braking being
done only by the circuit still working.
37 - 6
T I GHTENING MOME NTS (daNm)
Brake pump nut on servobrake 1,3
Servobrake attachment nut on the cowl panel 2,0
vnx.su

MECHAN ICAL ELEMENTS CONTROL
37
AIR FILTER REPLACEMENT
DISMOUNTING
Dismount the servobrake off the vehicle.
Loosen the lock nut (E) and dismount : -the coupling fork;
- the lock nut.
Remove the washer filter F.
RE MOUNTING
Mount the new washer filter
Mount: -the lock nut;
- the coupling fork.
A djust the value L = 1 17 + 0,5 mm .
Tighten the lock nut E on the coupling fork
Mount the servobrake on the vehicle.
Purge the braking circuit. S
ERVOBRAKE RETAINER VALVE
REPLACEMENT
Th e ope rati on is pe rform e d without
dismountin g the servobrake off the vehicle.
DIS MOUNTING
Disconnect the connection of the air suc-
tion hose with the servobrake retainer valve.
Dismount the valve by rotating a nd then
pulling it. Dismount the retainer valve gasket.
RE MOUNTING
Check the state of the retainer valve gasket
and replace it if necessary. Mount the new retainer valve gasket.
Attach and mount the new retainer valve.
Connect the air suction hose.
AIR FILTER – SERVOBRAKE RETAINER VALVE
37 - 9
vnx.su