NEW MODEL OUTLINEMO-28
EQUIPMENT LIST
: Standard OP: Option
EuropeGeneral
ENTRYMID
TECHNICALMID
ELEGANTGeneral
Countries
Exterior
Rear SpoilerWagonÐ
Side Protection MouldingOPOPOPOP
WindshieldGreenÐ
Front SideGreen
GlassRear Side & BackGreenGlassRear Side & BackWagonPrivacyOPOPOPÐ
Rear QuarterWagonGreenÐRear QuarterWagonPrivacyOPOPOPÐ
Chassis
195/65 R153ZZ-FE & 1ZZ-FE & 1AZ-FE
205/55 R161AZ-FSE & 1CD-FTVÐ
Tire205/55 R163ZZ-FE & 1ZZ-FE & 1AZ-FEOPOPOPOP
215/45 R171AZ-FEÐOPOPÐ215/45 R171AZ-FSEÐOPOPÐ
15 x 6J Steel3ZZ-FE & 1ZZ-FE & 1AZ-FE
16x61/2J Steel1AZ-FSE & 1CD-FTVÐ16 x 6 1/2 J Steel3ZZ-FE & 1ZZ-FE & 1AZ-FEOPOPOPOP
Disc Wheel16 x 6 1 / 2 JJ AluminumOPOPOPOP
16 x 6 1 / 2 JJ Light Weight AluminumOPOPOPOP
17 x 7JJ Aluminum1AZ-FEÐOPOPÐ17 x 7JJ Aluminum1AZ-FSEÐOPOPÐ
ABS (Anti-lock Brake System) with EBD (Electronic Brake force Distrib\
ution)
VSC (Vehicle Stability Control) & Brake1AZ-FSEÐ(y)Assist & TRC (Traction Control)1CD-FTVOPOPOPÐ
Wheel4-Spoke UrethaneÐÐWheel4-Spoke LeatherÐÐ
SteeringColumnManual Tilt & TelescopicSteeringEPS*13ZZ-FE & 1ZZ-FEÐ
Hydraulic Type Power
Steering1AZ-FSE & 1CD-FTV & 1AZ-FE
Body
CoverFabricCoverLeather1AZ-FSE & 1CD-FTVÐOPOPÐ
FrontManual
SeatFrontPower1AZ-FSE & 1CD-FTVÐOPOPÐ
FixSedanÐÐÐ
Rear60:40 FoldingSedanÐ
60:40 Double FoldingLiftback & WagonÐ
SeatBelt
Front3-Point ELR*2 Electrical Sensing Type Pretensioner
& Force Limiter
BeltRear3-Point ELR*2 & ALR*3
CRS (Child Restraint System) Anchor System (Rear Outside Seat Only)
*1: Electoronic Power Steering
*2: Emergency Locking Retractor
*3: Automatic Locking Retractor
http://vnx.su
Illustration:what to do and where
Component part No.
Detailed text: how to perform task
Task heading: what to do
Set part No
D31009
01±2
±
INTRODUCTION HOW TO USE THIS MANUAL
AVENSIS REPAIR MANUAL (RM1018E)
(c) Tightening torque, grease application area, and non±reusable parts are described as important points in the procedures.
NOTICE:
There are cases where such information can only be explained by using an illu\
stration. In these
cases, all the information such as torque, oil, etc. are described in the illu\
stration.
(d) Installing procedures are performed in the reverse order of the removal and only the important points are described.
(e) Only items with points are described in the procedure, and the operational portion \
and content are placed using an illustration. In the explanations, details of the operational \
method, standard value and
notices are placed.
(f) There may be a case where the illustrations of similar models are used. In th\
at case, specific details may be different from the actual vehicle.
(g) The procedures are presented in a step±by±step format: (1) The illustration shows what to do and where to do it.
(2) The task heading tells what to do.
(3) The explanation text tells how to perform the task and gives other information such as specifica-tions and warnings.
Example:
HINT:
This format provides an experienced technician with a FAST TRACK to the necessary information. The task
heading can be read at a glance when necessary and the text below provides deta\
iled information. Important
specifications and warnings always are written in bold type to stand out from the rest\
of the text.
5. SERVICE SPECIFICATIONS
(a) Specifications are presented in bold type throughout the manual. You never have to leave the proce- dure to look up your specifications. The specifications are also found in th\
e Service Specifications sec-
tion for quick reference.
6. TERMS DEFINITION
CAUTIONIndicates the possibility of injury to you or other people.
NOTICEIndicates the possibility of damage to the components being repaired.
HINTProvides additional information to help you to perform the repair efficiently.
http://vnx.su
010LF±01
D25016
±
INTRODUCTION REPAIR INSTRUCTION
01±5
AVENSIS REPAIR MANUAL (RM1018E)
REPAIR INSTRUCTION
PRECAUTION
1. BASIC REPAIR HINT
(a) HINTS ON OPERATIONS
1LooksAlways wear a clean uniform.
Hat and safety shoes must be worn.
2Vehicle protectionSet a grill cover, fender cover, seat cover and floor mat before starting operation.
3Safe operation
When working with 2 or more persons, be sure to check the safety of one \
another.
When working with the engine running, pay attention to providing ventila\
tion for exhaust fumes in the work-
shop.
When working with high±temperatures, rotating, moving or vibrating pa\
rts, be careful not to burn or injure
yourself.
When jacking up the vehicle, be sure to support the specified location w\
ith a safety stand.
When lifting up the vehicle, use safety equipment.
4Preparation of tools and
measuring gaugeBefore starting repairs, prepare the tool stand, SST, gauge, oil, shop rag and parts for replacement.
5
Removal and installation,
disassembly and assem-
bly operations
Diagnose with a thorough understanding of the trouble condition and perf\
orm effective operation.
Before removing the parts, check the general condition of the assembly, and for deformation and damage.
When the structure is complicated, take a notes or make matchmarks as no\
t to make mistakes that affect the
function of the parts.
Clean and wash the removed parts if necessary and assemble them after a \
thorough check.
6Removed parts
Place the removed parts in the correct order to avoid mixing them up or \
making them dirty.
As for non±reusable parts such as gaskets, O±rings, and self±lo\
cking nuts, replace them with new ones
following the instructions in this manual.
Organize the parts that were replaced in a box and show them to the cust\
omer.
http://vnx.su
D26613
Example:
D25080
Negative (±)
Terminal
±
INTRODUCTION REPAIR INSTRUCTION
01±15
AVENSIS REPAIR MANUAL (RM1018E)
(8) Oil or water should not be put on the front seat outer belt and the front seat outer belt should be
cleaned with the appropriate detergents.
(i) AIRBAG SENSOR ASSEMBLY (1) Never reuse the airbag sensor assembly involved in a collision where the\
SRS has deployed.
(2) The connectors to the airbag sensor assembly should be connected or disc\
onnected with thesensor mounted on the floor. If the connectors are connected or disconnected while the airbag
sensor assembly is not mounted to the floor, it could cause an undesired ignition of the supple-
mental restraint system.
(3) Work must be started after 90 seconds from the time the ignition switch is t\
urned to the ºLOCKº position and the negative (±) terminal cable is disconnected from the battery, even if only loosen-
ing the set bolts of the airbag sensor assembly.
(j) WIRE HARNESS AND CONNECTOR
(1) The SRS wire harness is integrated with the instrument panel wire harness a\
ssembly. All connec-tors in the system are a standard yellow color. If the SRS wire harness becomes disconnected
or the connector becomes broken due to an accident, etc., repair or repl\
ace it.
3. ELECTRONIC CONTROL
(a) REMOVAL AND INSTALLATION OF BATTERY TERMI-NAL
(1) Before performing electronic work, disconnect thebattery negative (±) terminal cable beforehand in
order to prevent it from shorting and burning out.
(2) When disconnecting and insta lling the terminal
cable, turn the ignition switch and lighting switch
OFF, and loosen the terminal nut completely. Per-
form these operations without twisting or prying the
terminal.
(3) When the battery terminal cable is removed, the memories of the clock, radio, DTCs, etc. are erased.
So before removing it, check them and make a note
of their settings.
(4) When the battery negative (±) terminal cable is dis- connected, memories of various systems are
erased. Therefore, refer to the PRE±CHECK for
each system to make sure whether or not the sys-
tem needs to be initialized after the battery negative
http://vnx.su
022L4±02
02±36
±
PREPARATION AUTOMATIC TRANSMISSION / TRANS
AVENSIS REPAIR MANUAL (RM1018E)
AUTOMATIC TRANSMISSION / TRANS
PREPARATION
SST
07110±58060Air Conditioner Service Tool SetTRANSMISSION CONTROL CABLE
ASSY
(07117±58060)Refrigerant Drain Service ValveTRANSMISSION CONTROL CABLE
ASSY
(07117±58070)T±JointTRANSMISSION CONTROL CABLE
ASSY
(07117±58080)Quick Disconnect AdapterTRANSMISSION CONTROL CABLE
ASSY
(07117±58090)Quick Disconnect AdapterTRANSMISSION CONTROL CABLE
ASSY
(07117±78050)Refrigerant Charging GaugeTRANSMISSION CONTROL CABLE
ASSY
(07117±88060)Refrigerant Charging HoseTRANSMISSION CONTROL CABLE
ASSY
(07117±88070)Refrigerant Charging HoseTRANSMISSION CONTROL CABLE
ASSY
(07117±88080)Refrigerant Charging HoseTRANSMISSION CONTROL CABLE
ASSY
09023±12700Union Nut Wrench 17mmAUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
09308±00010Oil Seal PullerFRONT DIFFERENTIAL OIL
SEAL(U241E)
FRONT DIFFERENTIAL OIL
SEAL(U341E)
09316±60011Transmission & Transfer Bearing
ReplacerFRONT DIFFERENTIAL OIL
SEAL(U241E)
http://vnx.su
±
PREPARATION AUTOMATIC TRANSMISSION / TRANS
02±37
AVENSIS REPAIR MANUAL (RM1018E)
(09316±00011)Replacer PipeFRONT DIFFERENTIAL OIL
SEAL(U241E)
09350±32014TOYOTA Automatic Transmission
Tool SetTORQUE CONVERTER CLUTCH
AND DRIVE PLATE(ATM)
AUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
(09351±32010)One±way Clutch Test ToolTORQUE CONVERTER CLUTCH
AND DRIVE PLATE(ATM)
AUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
(09351±32020)Stator StopperTORQUE CONVERTER CLUTCH
AND DRIVE PLATE(ATM)
AUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
09520±01010Drive Shaft Remover AttachmentAUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
FRONT DIFFERENTIAL OIL
SEAL(U341E)
09520±24010Differential Side Gear Shaft
PullerAUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
FRONT DIFFERENTIAL OIL
SEAL(U341E)
(09520±32040)Shocker SetAUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
FRONT DIFFERENTIAL OIL
SEAL(U341E)
09554±14010Differential Oil Seal ReplacerFRONT DIFFERENTIAL OIL
SEAL(U341E)
09628±62011Boll Joint PullerAUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
FRONT DIFFERENTIAL OIL
SEAL(U341E)
09649±17010Steering Knuckle ToolFRONT DIFFERENTIAL OIL
SEAL(U241E)
09726±27012Front Suspension Arm Bushing
Remover & ReplacerFRONT DIFFERENTIAL OIL
SEAL(U341E)
http://vnx.su
02±38
±
PREPARATION AUTOMATIC TRANSMISSION / TRANS
AVENSIS REPAIR MANUAL (RM1018E)
(09726±02041)ReplacerFRONT DIFFERENTIAL OIL
SEAL(U341E)
09930±00010Drive Shaft Nut ChiselAUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
FRONT DIFFERENTIAL OIL
SEAL(U341E)
09950±70010Handle SetFRONT DIFFERENTIAL OIL
SEAL(U241E)
FRONT DIFFERENTIAL OIL
SEAL(U341E)
(09951±07150)Handle 150FRONT DIFFERENTIAL OIL
SEAL(U241E)
(09951±07200)Handle 200FRONT DIFFERENTIAL OIL
SEAL(U341E)
Recomended Tools
09011±12301Socket Wrench 30 mmAUTOMATIC TRANSAXLE
ASSY(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
FRONT DIFFERENTIAL OIL
SEAL(U341E)
09040±00011Hexagon Wrench SetAUTOMATIC TRANSAXLE
ASSY(U241E)
TRANSMISSION WIRE(U241E)
TRANSMISSION VALVE BODY
ASSY(U241E)
FRONT DIFFERENTIAL OIL
SEAL(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
(09043±20100)Socket Hexagon Wrench 10AUTOMATIC TRANSAXLE
ASSY(U241E)
TRANSMISSION WIRE(U241E)
TRANSMISSION VALVE BODY
ASSY(U241E)
FRONT DIFFERENTIAL OIL
SEAL(U241E)
AUTOMATIC TRANSAXLE
ASSY(U341E)
TRANSMISSION VALVE BODY
ASSY(U341E)
TRANSMISSION WIRE(U341E)
FRONT DIFFERENTIAL OIL
SEAL(U341E)
09042±00010Torx Socket T30TRANSMISSION CONTROL CABLE
ASSY
http://vnx.su
022KL±01
±
PREPARATION DRIVE SHAFT / PROPELLER SHAFT
02±29
AVENSIS REPAIR MANUAL (RM1018E)
DRIVE SHAFT / PROPELLER SHAFT
PREPARATION
SST
09240±00020Wire Gauge SetFRONT DRIVE SHAFT
09520±00031Rear Axle Shaft PullerFRONT AXLE HUB SUB±ASSY LH
09520±01010Drive Shaft Remover AttachmentFRONT DRIVE SHAFT
09520±24010Differential Side Gear Shaft
PullerFRONT DRIVE SHAFT
(09520±32040)Shocker SetFRONT DRIVE SHAFT
09521±24010Rear Axle Shaft PullerFRONT DRIVE SHAFT
09527±10011Rear Axle Shaft Bearing RemoverFRONT DRIVE SHAFT
09527±17011Rear Axle Shaft Bearing RemoverFRONT AXLE HUB SUB±ASSY LH
09608±16042Front Hub Bearing Adjusting ToolFRONT DRIVE SHAFT
(09608±02021)Bolt & NutFRONT DRIVE SHAFT
(09608±02041)RetainerFRONT DRIVE SHAFT
09608±32010Steering Knuckle Oil Seal
ReplacerFRONT AXLE HUB SUB±ASSY LH
http://vnx.su