2003 TOYOTA AVENSIS window

700SA±01
B58278
1212345678910
11
24 23 22 21 2019 18 17 16 15 14 13
70±6
±
WINDSHIELD/WINDOWGLASS/MIRROR POWER WINDOW CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
INSPECTION
1. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSY
(a) Inspect the resistance between the terminals of the switch, as shown in the table below.
Standard:
Power window lock switch
Tester ConnectionSwitch PositionSpecified Condition
3 (PW) 23 (WL)UnlockBelow 1
3 (PW) ± 23 (WL)Lock10 k
or higher
Driver side switch (LHD models)
Tester ConnectionSwitch PositionSpecified Condition
2 (FLU) ± 3 (PW)AUTO UPBelow 1
3 (PW) ± 14 (FLA)AUTO UPBelow 1

2 (FLU) ± 3 (PW)MANUAL UPBelow 1

±OFF±
3 (PW) ± 4 (FLD)MANUAL DOWNBelow 1

3 (PW) ± 4 (FLD)AUTO DOWNBelow 1
3 (PW) ± 14 (FLA)AUTO DOWNBelow 1

Driver side switch (RHD models)
Tester ConnectionSwitch PositionSpecified Condition
2 (FRU) ± 3 (PW)AUTO UPBelow 1
3 (PW) ± 14 (FRA)AUTO UPBelow 1

2 (FRU) ± 3 (PW)MANUAL UPBelow 1

±OFF±
3 (PW) ± 4 (FRD)MANUAL DOWNBelow 1

3 (PW) ± 4 (FRD)AUTO DOWNBelow 1
3 (PW) ± 14 (FRA)AUTO DOWNBelow 1

Passenger side switch (LHD models)
Tester ConnectionSwitch PositionSpecified Condition
3 (PW) ± 10 (FRU)AUTO UPBelow 1
3 (PW) ± 11 (FRA)AUTO UPBelow 1

3 (PW) ± 10 (FRU)MANUAL UPBelow 1

±OFF±
3 (PW) ± 9 (FRD)MANUAL DOWNBelow 1

3 (PW) ± 9 (FRD)AUTO DOWNBelow 1
3 (PW) ± 11 (FRA)AUTO DOWNBelow 1

Passenger side switch (RHD models)
Tester ConnectionSwitch PositionSpecified Condition
3 (PW) ± 10 (FLU)AUTO UPBelow 1
3 (PW) ± 11 (FLA)AUTO UPBelow 1

3 (PW) ± 10 (FLU)MANUAL UPBelow 1

±OFF±
3 (PW) ± 9 (FLD)MANUAL DOWNBelow 1

3 (PW) ± 9 (FLD)AUTO DOWNBelow 1
3 (PW) ± 11 (FLA)AUTO DOWNBelow 1

http://vnx.su

B58521
134
68
No Pin
No Pin
No Pin
±
WINDSHIELD/WINDOWGLASS/MIRROR POWER WINDOW CONTROL SYSTEM
70±7
AVENSIS REPAIR MANUAL (RM1018E)
Rear LH switch
Tester ConnectionSwitch PositionSpecified Condition
3 (PW) ± 17 (RLU)AUTO UPBelow 1
3 (PW) ± 16 (RLA)AUTO UPBelow 1

3 (PW) ± 17 (RLU)MANUAL UPBelow 1

±OFF±
3 (PW) ± 15 (RLD)MANUAL DOWNBelow 1

3 (PW) ± 15 (RLD)AUTO DOWNBelow 1
3 (PW) ± 16 (RLA)AUTO DOWNBelow 1

Rear RH switch
Tester ConnectionSwitch PositionSpecified Condition
3 (PW) ± 18 (RRU)AUTO UPBelow 1
3 (PW) ± 22 (RRA)AUTO UPBelow 1

3 (PW) ± 18 (RRU)MANUAL UPBelow 1

±OFF±
3 (PW) ± 19 (RRD)MANUAL DOWNBelow 1

3 (PW) ± 19 (RRD)AUTO DOWNBelow 1
3 (PW) ± 22 (RRA)AUTO DOWNBelow 1

If the result is not as specified, replace the switch assy.
2. INSPECT POWER WINDOW REGULATOR SWITCH
ASSY
HINT:
The passenger, rear LH and rear RH regulator switches are all
the same.
(a) Check the resistance between the terminals of the switch connector, as shown in the table below.
Standard:
Tester ConnectionSwitch PositionSpecified Condition
1 (UP) ± 8 (WL)AUTO UPBelow 1
3 (AUTO) ± 8 (WL)AUTO UPBelow 1

1 (UP) ± 8 (WL)MANUAL UPBelow 1

±OFF±
6 (DOWN) ± 8 (WL)MANUAL DOWNBelow 1

3 (AUTO) ± 8 (WL)AUTO DOWNBelow 1
6 (DOWN) ± 8 (WL)AUTO DOWNBelow 1

If the result is not as specified, replace the switch assy.
http://vnx.su

B58265
Up
Down
1 2 3
4
5 6
B58557
Up
Down
12
3
4 5 6
70±8
±
WINDSHIELD/WINDOWGLASS/MIRROR POWER WINDOW CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
3. INSPECT FRONT DOOR WINDOW REGULATOR SUB±ASSY LH
(a) Inspect operation of the power window regulator.
(1) Apply battery voltage to the connector terminals.
(2) Check that the regulator smoothly operates.
Standard:
Measurement ConditionSpecified Condition
Battery positive (+)
6
Battery negative (±)
4Battery positive (+)
2Regulator moves upward
Battery positive (+)
6
Battery negative (±)
4Battery positive (+)
1Regulator moves
downward
(b) Inspect operation of the PTC inside the power window regulator motor.
NOTICE:
The work must be performed with the power window regu-
lator and door glass installed in the vehicle. (1) Set an electrical tester DC 400 A probe to the wireharness of terminal 4 or 6.
NOTICE:
Match the arrow mark of the probe with the current direc-
tion. (2) Fully close the door glass by operating the powerwindow switch and keep the door glass there for
approximately 60 seconds.
(3) Try to operate the power window past the fully
closed position using the power window switch and
measure the time until the electrical current
changes into 1 A from 16 to 34 A (Inspection of cur-
rent shut±off).
Standard: Less than 1 second
(4) Check that the door glass goes down when the
power window regulator switch is pushed DOWN.
If the result is not as specified, replace the regulator sub±assy.
4. INSPECT FRONT DOOR WINDOW REGULATOR SUB±ASSY RH
(a) Inspect operation of the power window regulator.
(1) Apply battery voltage to the connector terminals.
(2) Check that the regulator smoothly operates.
Standard:
Measurement ConditionSpecified Condition
Battery positive (+)
6
Battery negative (±)
4Battery positive (+)
2Regulator moves upward
Battery positive (+)
6
Battery negative (±)
4Battery positive (+)
1Regulator moves
downward
(b) Inspect operation of the PTC inside the power window regulator motor.
http://vnx.su

B58266
12 3
4 56
Up
Down
±
WINDSHIELD/WINDOWGLASS/MIRROR POWER WINDOW CONTROL SYSTEM
70±9
AVENSIS REPAIR MANUAL (RM1018E)
NOTICE:
The work must be performed with the power window regu-
lator and door glass installed in the vehicle.
(1) Set an electrical tester DC 400 A probe to the wireharness of terminal 4 or 6.
NOTICE:
Match the arrow mark of the probe with the current direc-
tion. (2) Fully close the door glass by operating the powerwindow switch and keep the door glass there for
approximately 60 seconds.
(3) Try to operate the power window past the fully
closed position using the power window switch and
measure the time until the electrical current
changes into 1 A from 16 to 34 A (Inspection of cur-
rent shut±off).
Standard: Less than 1 second
(4) Check that the door glass goes down when the power window regulator switch is pushed DOWN.
If the result is not as specified, replace the regulator sub±assy.
5. INSPECT REAR DOOR WINDOW REGULATOR
SUB±ASSY LH
(a) Inspect operation of the power window regulator motor. (1) Apply battery voltage to the connector terminals.
(2) Check that the regulator smoothly operates.
Standard:
Measurement ConditionSpecified Condition
Battery positive (+)
6
Battery negative (±)
4Battery positive (+)
2Regulator moves upward
Battery positive (+)
6
Battery negative (±)
4Battery positive (+)
1Regulator moves
downward
(b) Inspect operation of the PTC inside the power window regulator motor.
NOTICE:
The work must be performed with the power window regu-
lator and door glass installed in the vehicle.
(1) Set an electrical tester DC 400 A probe to the wireharness of terminal 4 or 6.
NOTICE:
Match the arrow mark of the probe with the current direc-
tion.
(2) Fully close the door glass by operating the powerwindow switch and keep the door glass there for
approximately 60 seconds.
(3) Try to operate the power window past the fully closed position using the power window switch and
measure the time until the electrical current
changes into 1 A from 16 to 34 A (Inspection of cur-
rent shut±off).
Standard: Less than 1 second
http://vnx.su

B58558
UpDown
12 3
4 56
B690245
2 1
3 5
3
2
1
70±10
±
WINDSHIELD/WINDOWGLASS/MIRROR POWER WINDOW CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
(4) Check that the door glass goes down when the power window regulator switch is pushed DOWN.
If the result is not as specified, replace the regulator sub±assy.
6. INSPECT REAR DOOR WINDOW REGULATOR SUB±ASSY RH
(a) Inspect operation of the power window regulator. (1) Apply battery voltage to the connector terminals.
(2) Check that the regulator smoothly operates.
Standard:
Measurement ConditionSpecified Condition
Battery positive (+)
6
Battery negative (±)
4Battery positive (+)
2Regulator moves upward
Battery positive (+)
6
Battery negative (±)
4Battery positive (+)
1Regulator moves
downward
(b) Inspect operation of the PTC inside the power window regulator motor.
NOTICE:
The work must be performed with the power window regu-
lator and door glass installed in the vehicle. (1) Set a electrical tester DC 400 A probe to the wireharness of terminal 4 or 6.
NOTICE:
Match the arrow mark of the probe with the current direc-
tion. (2) Fully close the door glass by operating the powerwindow switch and keep the door glass there for
approximately 60 seconds.
(3) Try to operate the power window past the fully
closed position using the power window switch and
measure the time until the electrical current
changes into 1 A from 16 to 34 A (Inspection of cur-
rent shut±off).
Standard: Less than 1 second
(4) Check that the door glass goes down when the power window regulator switch is pushed DOWN.
If the result is not as specified, replace the regulator sub±assy.
7. INSPECT IG1 RELAY
(a) Check resistance of the relay. Standard:
Tester ConnectionSpecified Condition
10 k or higher
3 ± 5Below 1 
(When battery voltage is applied to terminals 1 and 2)
If the result is not as specified, replace the relay.
http://vnx.su

B66773
DADBDN
Vehicle Front Side
Vehicle Rear Side
DB
DA DH DC
DN
DC
DH
Integration Relay
±
WINDSHIELD/WINDOWGLASS/MIRROR POWER WINDOW CONTROL SYSTEM
70±11
AVENSIS REPAIR MANUAL (RM1018E)
8. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSY (INTEGRATION RELAY)
http://vnx.su

B58556
Front Door
Courtesy Lamp
SwitchPushed
Free
Body Ground
70±12
±
WINDSHIELD/WINDOWGLASS/MIRROR POWER WINDOW CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
(a) Disconnect the DA, DB, DC, DH and DN J/B connectors.
(b) Check the voltage and resistance between each terminal of the wire harness si\
de connectors and the body ground.
Standard:
Tester ConnectionConditionSpecified Condition
DA±8 ± Body groundNo key inserted in ignition key cylinder
Ye s10 k
or higher
Below 1

DA±9 ± Body groundConstantBelow 1

B±13 ± Body groundDriver side door CLOSED
OPEN10 k
or higher
Below 1

DC±9 ± Body groundPassenger side door CLOSED
OPEN10 k
or higher
Below 1

DH±5 ± Body groundIgnition switch ON
Others10 to 14 V
0 V
DN±1 ± Body groundConstant10 to 14 V
If the result is not as specified, there may be a malfunction on the wir\
e harness side or the J/B assy (integra-
tion relay) may have a malfunction.
(c) Reconnect the DA, DB, DC, DH and DN J/B connectors.
(d) Check the voltage of terminal 5 of the DH connector.
Standard:
Tester ConnectionConditionSpecified Condition
DH±5 ± Body groundIgnition switch ON
Others10 to 14 V
0 V
If the result is not as specified, there may be a malfunction on the wir\
e harness side or the J/B assy (integra-
tion relay) may have a malfunction.
9. INSPECT FRONT DOOR COURTESY LAMP SWITCHASSY
(a) Remove the courtesy lamp switch.
(b) Check the switch resistance. Standard:
Tester ConnectionSwitch PositionSpecified Condition
1 Body groundSwitch pushed10 k
or higher1 ± Body groundSwitch freeBelow 1

If the result is not as specified, replace the switch assy.
http://vnx.su

700SB±01
±
WINDSHIELD/WINDOWGLASS/MIRROR POWER WINDOW CONTROL SYSTEM
70±13
AVENSIS REPAIR MANUAL (RM1018E)
RESET
NOTICE:

The power window regulator motor must be reset when the fitting of the door glass is adjusted
or when the door glass run is replaced.

Whenever disconnecting the battery terminal, reset all the other systems besides the power
window control system.
1. RESET WINDOW REGULATOR SUB±ASSY (REGULATOR MOTOR)
(a) Turn the ignition switch ON.
(b) Operate the power window using the master (regulator) switch.
(c) Disconnect the battery, fuse or motor connector while the power window is operating, so that t\
he power window motor is forced to stop.
(d) Reconnect the battery, fuse or motor connector.
(e) Pull up the power window switch until the power window is fully closed and h\
old the switch at least 1 second.
(f) Check that the AUTO UP/DOWN function operates completely.
http://vnx.su