2003 TOYOTA AVENSIS window

±
THEFT DETERRENT & DOOR LOCK THEFT DETERRENT SYSTEM
73±35
AVENSIS REPAIR MANUAL (RM1018E)
6. INTRUSION (THEFT WARNING) SENSOR
(a) Function of the intrusion sensor:
The intrusion sensor (theft warning redar sensor) senses any moving objec\
t by using ultrasonic waves
and outputs the signals to communicate an intrusion to the theft warning ECU so that\
the theft deterrent
system can set off the alarm.
When the theft deterrent system is switched to the arming preparation st\
ate, the intrusion sensor is
supplied with S+B by the theft warning ECU. This causes the theft deterrent system to set off the alarm
when the signal is input from the intrusion sensor in a situation such a\
s the window glass being broken.
(b) Press the intrusion sensor OFF switch.
HINT:
The theft deterrent system can be set (switched to the arming preparation state) with the intrusion sensor
OFF when an animal is left inside the vehicle. (1) Make sure that the theft deterrent system is in the disarmed state.
(2) Press the intrusion sensor OFF switch once.
HINT:
The intrusion sensor and the OFF switch are provided on the roof console\
box in the vehicle front interior.
NOTICE:
The intrusion sensor returns to ON (initial state) when the doors are unl\
ocked by the wireless opera-
tion.
7. THEFT WARNING (SELF±POWER) SIREN
(a) The theft warning siren has an internal battery. If any of the vehicle's battery or communication lines are opened, the theft warning siren detects it by itself and sounds. Although the theft warning siren
usually sounds by receiving a signal from the theft warning ECU usually, the theft warning siren can
sound using its internal battery in case that the vehicle's battery is opened.
(b) The theft warning ECU sends an arming signal to the theft warning siren while transferring to the armed
state, as well as sending a disarming signal to the siren while transferring t\
o the disarmed state. Addi-
tionally, the theft warning ECU can sound the theft warning siren by sending an a\
larm signal in the
alarm sounding state.
http://vnx.su

B66546 B66546
Front Pillar Garnish RH
Cowl Side Trim
Board RH
Front Door Opening Trim
Weatherstrip RH
Front Door
Scuff Plate RH
Center Pillar Garnish
Lower RH
Center Pillar Garnish
Upper RH
Rear Door
Opening Trim
Weatherstrip RH
Rear Door
Scuff Plate RH
Front Door
Scuff Plate LH
Rear Door
Scuff Plate LH
Cowl Side Trim
Board LH
Front Door Opening Trim
Weatherstrip LHRear Door
Opening Trim
Weatherstrip LH
Center Pillar
Garnish
Lower LH
Deck Floor
Box Rear
Tonneau Cover
Assy
Deck Board
Sub±assy
Deck Floor
Box Front
Deck Floor
Box RH
Deck Floor
Box LH
Deck Trim
Side Board RH
Deck Trim
Side Board LH
Roof Side
Garnish Inner RH
Roof Side
Garnish Inner LH Rear Window Side
Garnish RH
Rear Window Side
Garnish LH
Center Pillar
Garnish
Upper LH
Front Pillar Garnish LH
N

m (kgf
cm ft
lbf): Specified torque
74±12
±
SLIDING ROOF/CONVERTIBLE SLIDING ROOF
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

7408T±01
±
SLIDING ROOF/CONVERTIBLE SLIDING ROOF SYSTEM
74±3
AVENSIS REPAIR MANUAL (RM1018E)
ON±VEHICLE INSPECTION
1. CHECK WINDOW LOCK SWITCH
(a) Check that operation of the power windows excluding the driver side and the s\
liding roof are disabled
when the window lock switch of the power window master switch is pressed.
(b) Check that the power windows and the sliding roof can be operated when the window lock switch is pressed again.
2. CHECK AUTO SLIDE±OPEN/CLOSE FUNCTION
(a) Check that the sliding roof switch can operate the sliding roof as follows when the tilt±UP/ DOWN func-
tion is not being used:
Standard:
ConditionSwitch ConditionSwitch OperationRoof Glass

Ignition switch ONSLIDE OPENPressed for more than 0 3 secFully openIgnition switch ON

Window lock switch OFFTILT UPPressed for more than 0.3 sec.Fully closed
HINT:
The sliding roof stops partway when the sliding roof switch is pushed on\
either side during AUTO operation.
3. CHECK AUTO TILT UP/DOWN FUNCTION
(a) Check that the sliding roof switch can operate the sliding roof as follows wh\
en the slide±OPEN/CLOSE
function is not being used:
Standard:
ConditionSwitch ConditionSwitch OperationRoof Glass

Ignition switch ONTILT UPPressed for more than 0 3 secFully tilted upIgnition switch ON

Window lock switch OFFSLIDE OPENPressed for more than 0.3 sec.Fully closed
HINT:
The sliding roof stops partway when the sliding roof switch is pushed on\
either side during AUTO operation.
4. CHECK SLIDING ROOF OPERATION FUNCTION AFTER IGNITION IS TURNED OFF
(a) When both of the following conditions are fulfilled, check that the power wi\
ndows and the sliding roof
can be operated even after the ignition switch is turned OFF:

Within 43 seconds after the ignition switch is turned OFF

When the driver side door is closed
5. CHECK JAM PROTECTION FUNCTION
HINT:
The jam protection function prevents any part of your body from getting caught by accident between the ve-
hicle body and the roof glass during sliding roof operation.
Operative condition:

AUTO CLOSE

AUTO CLOSE during sliding roof operation after the ignition switch is turne\
d OFF

AUTO TILT±DOWN

AUTO TILT±DOWN during sliding roof operation after the ignition switch is tur\
ned OFF
CAUTION:

Do not check this function using a part of your body such as your hand. \
Also, pay thorough
attention that nothing gets caught by accident during this process.

If this function is checked by inserting a thin object (less than 5 mm \
(0.20 in.)) between the roof
glass and vehicle body, it may not operate.
http://vnx.su

750MV±01
B67988
Front Door Glass
Sub±assy LH
Front Door Glass Run LH
Front Door Frame Sub±assy Rear Lower LH
8.0 (82, 71 in.´lbf)
Front Door Glass Weatherstrip Inner LH
Front Door Trim Board Sub±assy LH
Front Door Armrest
Base Panel Upper
Courtesy Lamp : Specified torque
N´m (kgf´cm, ft´lbf) Front No. 1 Speaker Assy
Front Door Inside Handle Sub±assy LH
Fuel Lid Opener Switch
Front Door Trim Base LHClip
Power Window Regulator
Switch Assy
Front Door Armrest Base Panel Upper
w/o Rear Power Window
Front Door Window Regulator
Sub±assy LH
8.0 (82, 71 in.´lbf)
Power Window Regulator
Master Switch Assy
Rivet
Non±reusable part



5.5 (56, 49 in.´lbf)
75±4
±
ENGINE HOOD/DOOR FRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
FRONT DOOR
COMPONENTS
http://vnx.su

B70388
B66971: Clip
Protective
TapeProtective
Tape
Screw
BoltCushion Rubber
B70121
B68930
Claw A
: Claw
1
2
±
ENGINE HOOD/DOOR FRONT DOOR
75±9
AVENSIS REPAIR MANUAL (RM1018E)
4. REMOVE POWER WINDOW REGULATOR MASTER
SWITCH ASSY
(a) Using a screwdriver, disengage the 4 claws and clip, and
remove the armrest base panel upper together with the
switch.
HINT:
Tape the screwdriver tip before use.
(b) Disconnect the switch connector.
(c) Remove the 3 screws and switch from the armrest base panel upper.
5. REMOVE FRONT DOOR TRIM BOARD SUB±ASSY LH
(a) Disconnect the courtesy lamp connector.
(b) Remove the 3 cushion rubbers.
(c) Remove the 2 screws and bolt as indicated.
(d) Using a clip remover, disengage 9 clips.
(e) Remove the trim board upward.
HINT:
In order to prevent the door panel from being damaged, cover
the areas indicated by the arrow marks in the illustration with
protective tape.
(f) Disengage the 2 claws and remove the courtesy lamp.
6. REMOVE FRONT DOOR GLASS WEATHERSTRIP INNER LH
(a) Remove the weatherstrip inner upward in the direction in- dicated by the arrow mark in the illustration.
7. REMOVE FRONT DOOR INSIDE HANDLE SUB±ASSY LH
(a) Using a screwdriver, disengage the claw A indicated.
HINT:
Tape the screwdriver tip before use.
(b) Move the inside handle in the direction indicated the by arrow mark in the illustration.
(c) Disconnect the 2 cables from the inside handle.
http://vnx.su

B62422
B62423
12
B66968
B61434

B68932Hole Plug
±
ENGINE HOOD/DOOR FRONT DOOR
75±11
AVENSIS REPAIR MANUAL (RM1018E)
14. REMOVE FRONT DOOR GLASS SUB±ASSY LH
HINT:
Insert a shop rag inside the door panel to prevent the glass from
being scratched.
(a) Move the door glass until the bolts appear in the service
holes.
(b) Remove the 2 bolts holding the door glass to the window
regulator.
(c) Remove the door glass in the direction indicated by the arrows in the illustration.
NOTICE:

Do not damage the glass.

When the bolts are removed, the glass may fall and
become deformed.
(d) Remove the glass run.
15. REMOVE FRONT DOOR WINDOW REGULATOR SUB±ASSY LH
(a) Disconnect the window regulator connector.
(b) Remove the 6 bolts and window regulator.
NOTICE:
When the bolts are removed, the window regulator may fall
and become deformed.
HINT:
Remove the window regulator through the service hole.
16. REMOVE FRONT DOOR FRAME SUB±ASSY REAR LOWER LH
(a) Remove the bolt and frame.
HINT:
Remove the frame through the service hole.
17. REMOVE FRONT DOOR OUTSIDE HANDLE COVER
(a) Remove the hole plug.
(b) Using a torx socket wrench (T30), loosen the screw and remove the cover with the door lock key cylinder installed.
http://vnx.su

B66894
B56613
12
B70122
Screw
B57102
B68928
75±12
±
ENGINE HOOD/DOOR FRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
18. REMOVE FRONT DOOR W/MOTOR LOCK ASSY LH
(a) Disconnect the door lock connector.
(b) Using a torx socket wrench (T30), remove the 3 screws and door lock.
NOTICE:
When the bolts are removed, the window regulator may fall
and become deformed.
HINT:
Remove the door lock through the service hole.
19. REMOVE FRONT DOOR HANDLE ASSY OUTSIDE LH
(a) Remove the handle pushing and pulling it in the direction indicated by the arrow mark in the illustration.
(b) Remove the outside handle pads front and rear.
20. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB±ASSY LH
(a) Using a torx socket wrench (T30), loosen the screw of the frame.
(b) Using pliers, disengage the clips and remove the frame, as shown in the illustration.
NOTICE:
Be sure to remove the outside handle together with the
clips, as the clips will be damaged if they remain attached
to the door panel.
HINT:
Remove the frame through the service hole.
21. REMOVE FRONT DOOR CHECK ASSY LH
(a) Remove the 2 nuts, bolt and check.
HINT:
Remove the check through the service hole.
http://vnx.su

B65961
Rod
B66894
Adhesive
Adhesive

B68932Hole Plug
B62425
B66972
75±14
±
ENGINE HOOD/DOOR FRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
(c) Insert the control rod into the door lock, and then set it to the door panel.
NOTICE:
Make sure that the handle link is securely engaged with the
lock.
(d) Apply adhesive to the threads of the 3 screws. Adhesive:
Part No. 08833±00070, THREE BOND 1324 or equiva-
lent
(e) Using a torx socket wrench (T30), install the door lock with the 3 screws.
Torque: 5.0 N
m (51 kgf
cm, 44 in.
lbf)
(f) Connect the door lock connector.
27. INSTALL FRONT DOOR OUTSIDE HANDLE COVER
(a) Using a torx socket wrench (T30), install the cover with the door lock key cylinder installed with the screw.
Torque: 7.0 N
m (71 kgf
cm, 62 in.
lbf)
(b) Install the hole plug.
28. INSTALL FRONT DOOR FRAME SUB±ASSY REAR
LOWER LH
(a) Install the frame with the bolt. Torque: 5.5 N
m (56 kgf
cm, 49 in.
lbf)
29. I N S TA L L F R O N T D O O R W I N D O W R E G U L ATO R SUB±ASSY LH
(a) Apply MP grease to the sliding and rotating areas of the
window regulator.
NOTICE:
Do not apply grease to the spring of the window regulator.
http://vnx.su