2003 SSANGYONG MUSSO wiring

5D2-6 TRANSFER CASE (TOD) Input/Output diagram TOD control unit and main wiring harness is linked by 30 pin
connector. Each pin joins with switche and actuator whosedetails refer to the below diagram.
Battery Power
Ignition ON/OFF
Position Encoder 1
Position Encoder 2
Position Encoder 3
Position Encoder 4
4H / 4L Switch Signal
A/T “N” Position Signal
Speed / TPS Supply
Front Speed Sensor Input
Rear Speed Sensor Input
ABS Operation Signal
Brake Switch Signal
4 5271028309241611292526
19 CAN H
CAN L
Shift Motor output port (LO-HI)
Shift Motor output port (HI-LO)
EMC
'4L' Indicator
Position Return
'4WD CHECK' IND
TPS/speed Sensor Ground (Speed / TPS Return)
2 13216713
1514
K-Line
20
22
23
17 18

TRANSFER CASE (TOD) 5D2-21
DIAGNOSIS Malfunction interior TOD control unit ; fault code 1714
Phenomenon
1. When ignition “ON ”, “4WD CHECK ” lamp illuminates
continuously.
2. On diagnosis by SCAN-100, it displays fault code “1714 ”.
Cause ; Error of EEPROM checksum in TOD control unit
Test Stage / Contents
Result
Stage T est Contents and Procedure Specified Value
/Yes/No Countermeasure
Check power supply for TOD control unit. 1. Disconnect 30 pin connector from TOD control unit.
2. Ignition “ON ”.
3. Using multi-tester, measure voltage between pin 5(+)
and 17/18 (-). - Specified value - Measured value is within specified range ? 11-14 Vdc
Ye sNo Perform A2 stagePerform A3 stage
Check connection status in TOD control unit connector.
1. Check connection status.
- Is it connected exactly?
2. In case of mal-connection, connect tightly then perform the follows.
a. Delete fault code using Scan-100.
b. Ignition “OFF ”.
c. Ignition “ON ”.
d. Diagnose by Scan-100.
- Does it display fault code “1714 ”? Ye s
No
Ye s No
Check short of 10A fuse (fuse No.20).
1. Detach No.20 fuse from engine room fuse box.
2. Check the existence of short.
- Is fuse normal? Yes
No
Check ground of TOD control unit.
1. Ignition “ON ”.
2. Check voltage between 4/19 (+) pin and 17/18 (-)
using multi-tester (keep connection status).
- Specified value (battery is good)
- Measured value
3. Check short between 17/18 pin and body after disconnect 30 pin connector.
- Is resistance " "? 12Vdc (battery
voltage)
Ye s
No
Ye sNo
A1 A2 A3 A4
Perform A3 stage Perform A2 stage Perform A3 stage Normal system Perform A4 stage Replace fuse, then perform A1 stage Perform A4-3 stage Replace TOD controlunit Repair ground wiring Ground is O.K., perform A5 stage

TRANSFER CASE (TOD) 5D2-23
Error of signal in engine throttle position ; fault code 1715, 1716
Phenomenon
1. Upon diagnosis by SCAN-100, it display on 1715,
1716 codes.
Cause
1. Bad communication line between E/G ECU and CAN.
2. Defect of TOD control unit.
3. Defect of E/G ECU.
Check connection status of connector through CAN communication line.
1. Check connection of connector.
- Does connector connect correctly between TOD
control unit and E/G ECU?
2. In case of bad connection, connect correctly then
perform the follows ;
a . Delete the memorized fault code using SCANNER.
b. Ignition “OFF ”.
c. Ignition “ON ”.
d. Diagnose by SCANNER.
- Does it display fault codes “1715 ” or “1716 ”. Ye s
No
B1
Ye sNo
Check connection status of CAN communication line towards E/G ECU.
1. Ignition “OFF ”.
2. Disconnect 30 pin connector towards TOD control unit.
3. Measure resistance between pin No.22 and 23 in wiring connector using multi-tester.
- Specified value
- Measured value is within specified range?
B2
115-125
Ye s
No
Check connection status of CAN communication line towards TOD control unit.
1. Ignition “OFF ”.
2. Disconnect coupling of E/G ECU (gray, 1-60 pin).
3. Measure resistance between pin No.37 and 38 in coupling using multi-tester.
- Specified value
- Measured value is within specified range?
B3
115-125
Ye s
No
Test Stage / Contents
Result
Stage T est Contents and Procedure Specified Value
/Yes/No Countermeasure
Perform B2 stage Perform B1-2 stage Perform B2 stage Normal system
Perform B3 STAGE Perform B4 stage, check and replace E/ G ECU
Perform B5 STAGE Replace TOD control unit

TRANSFER CASE (TOD) 5D2-25
Error in electro - magnetic clutch : fault code “1721 ”, “1722 ”
Phenomenon
1. Upon diagnosis by SCAN-100, it displays on fault
codes “1721,1722 ”.
Cause
1. Defect in electro - magnetic clutch
2. Defect in connector or wiring
- Open or short from EMC to the supply : 1721
- Short EMC to ground : 1722
Ye sNo
C1
Ye sNo
Ye s
No
11-15Vdc Ye s
No
C2
Ye sNo
Test Stage / ContentsResult
Stage T est Contents and Procedure Specified Value
/Yes/No Countermeasure
Check relevant connector connection status.
1. Check relevant connector connection status with TOD
control unit.
- Does it connect correctly ?
2. Check connection status of speed sensor and clutch coil connector (7 pin) in transfer case.
- Does it connect correctly ?
3. In case of bad connection, connect it correctly then perform the follows :
a. Delete the memorized fault code in control unit withScan - 100.
b. Ignition “OFF ”.
c. Ignition “ON ”.
d. Diagnose by SCAN-100
- Does it display on fault codes “1721,1722 ” ?
Check supply voltage into electro-magnetic clutch.
1. Ignition “ON ”
2. Measure voltage between pin 4/19(+) and 17/18(-) in TOD control unit connector.
- Specified value
- Measured value is within specified range ?
3. If the specified value would not be measured, perform the follows :
a. Check battery voltage (charging condition)
b. Check open circuit on No.13 fuse (20A)
c. Check relevant wires.
- Is the above 3a, 3b, 3c normal ? Perform C1-2 stage Perform C1-3 stage Perform C2 stage Normal system
Perform C2 stage Perform C1-3 stage Perform C3 stage Perform C2-3 stage Perform C3 stage

Charging/ Replace battery
Replace fuse
Repair wires

5D2-26 TRANSFER CASE (TOD)0Vdc
11 - 15Vdc
Ye s
No
2.5
Ye s No
C3 Test Stage / Contents
Result
Stage T est Contents and Procedure Specified Value
/Yes/No Countermeasure
Check resistance of electro-magnetic clutch.
1. Disconnect 30 pin connector from TOD control unit.
2. Measure resistance between pin 3 and 7 in wiring
connector using multi-tester.
- Specified value
- Measured value is within specified range? Perform C4 stage

0 : short
: open
C4 Check operational voltage of elector-magnetic clutch.
1. Ignition "ON"
2. Measure voltge between pin 3(+) and 17(-)in TOD control unit connector.
- Specified value 4WD high 4WD low
- Measure value is within specified range ? Replace TODcontrol unit Replace wire

5D2-28 TRANSFER CASE (TOD)
Ye sNo
D4 Test Stage / Contents
Result
Stage T est Contents and Procedure Specified Value
/Yes/No Countermeasure
Check output voltage of front and rear speed sensor.
1. Upon driving mode
2. Measure output voltage of front and rear speed sensor
by multi-tester. Check voltage whether it varies withinspecified range.
- Specified value Front speed sensor
: Pin 11(+), 13(-) in TOD control unit connector
 Rear speed sensor: Pin 29(+), 13(-) in TOD control unit connector- Measure value is within specified range ? Check function ofcontrol unit.
It necessary, replace then delete fault codes and re- diagnose . Perform D5 stage
Ye s
No
D5
Check short/open in cable.
1. Ignition"OFF"
2. Disconnect TOD control unit connector
3. Make a test for open circuit between pin 11 and 13, 16 and 13, 29 and 13 in wiring connector by multi-tester.
- Is there a resistance of " " ?
4. Make a test for short between pin 11 and ground 13 and ground, 29 and ground by multi-tester.
- Is there a resistance of " " ? Repair wire Perform D5-4 stge
Ye s No Wiring short, repairPerform D3 stage, then delete fault codes with rediagnosis

TRANSFER CASE (TOD) 5D2-29
Shift motor malfunction : Fault code ® 1741,
1742, 1743
Phenomenon
1. When change the 4H/4L switch from 4H to 4L, ‘4L ’
indicator lamp turn off after blinking for a time and then ‘ 4WD CHECK ’ indicator lamp turn on.
2. Fault codes display by diagnosis of SCAN-100 : 1741, 1742, 1743
3. The shifting operation is not occurred when 4H / 4L switch, is operating.
Cause
Defect in shift motor, improper voltage provided, incorrect
connection in connector, short of wiring.
11-14 V
(Battery voltage) Ye s
No
E1
11-14 V
(Battery voltage)
Ye sNo
Ye sNo
E2
Ye sNo
Test Stage / Contents
Result
Stage T est Contents and Procedure Specified Value
/Yes/No Countermeasure
Check the input voltage of shift motor.
1. Turn the ignition switch to
“ON ” position.
2. Measure the Hi/Low voltage of motor which is located between No.1/No.14 and No.2/No.15 connector of TOD control unit with digital Multi-tester or which is locatedbetween No.G connector and body after detaching T/C
motor connector.
- The specified value (When operates 4H/4L switch)
- Measured value is within specified range ?
3. Measure the Hi/Low voltage of motor which is located between No.2/No.5 and No.1/No.14 connector or which is located No.B connector and body after detaching T/C motor connector
- The specified value (When operates 4H/4L switch)
- Measured value is within specified range ?
Check the fault condition of the relevant connector.
1. Check the installation condition of TOD control unit 30pin connector and T/C shift motor connector.
- Is it installed properly ?
2. If the connector installation is improper, install properly and then perform follows :
a. Delete the fault code of control unit by scan scope
b. Turn off the ignition switch
c. Turn on the ignition switch
d. Re-diagnosis of system
It displays one or more fault code among 1741 to 1743. Perform E1-3 stagePerform E2 stage Perform E4 stage Perform E2 stage Perform E3 stage Perform E2-2 stage Perform E3 stage Normal system

5D2-30 TRANSFER CASE (TOD)
Ye sNo
Ye s No
Ye s No
E3
Ye s
No
E4
Ye s
No
E5 Test Stage / Contents
Result
Stage T est Contents and Procedure Specified Value
/Yes/No Countermeasure
Check the wiring of shift motor whether it is shorted or not.
1. Turn off the ignition switch.
2. Detach the 30pin connector from TOD control unit
3. Perform short test between the wiring connector No.1/ No.14 and No.2/No.5.
- Is there resistance of 0 ?
4. Perform the short test between No.1/No.14 Connector and body, No2/No.15 connector and body.
- Is there resistance of 0 ?
5. Execute E1 stage to check whether wiring is shorted between Hi-Low motor and LOW-HI motor.
- Is the provided voltage proper ?
Check the resistance of shift motor 1. Turn off the ignition switch.
2. Measure the resistance between No.1/No.14 and No.2/ No.15 connector after detaching 30pin connector of TOD
control unit Or, check the resistance between No.G andNo.B after detaching motor connector of T/C side.
- Specified value
- Measured value is within specified range ?
Execute the test after detaching shift motor, when the faultis not solved after executing E1~E4 stage. 1. Detach the motor connector from T/C.
2. Remove the shift motor.
3. Connect motor connector with the removed shift motor.
4. Operate the 4H/4L switch. - Does motor rotate ? Hi-Low motor and Lo-Hi wiring are
shorted each other. Repair or replace.Perform E3-4 stage. Related wiring is shorted with ground.Repair or replace. Perform E3-5 stage. Perform E4 stage. Wiring is shorted. Repair or replace. The defective T/C or perform E5 stage. Replace the shift
motor.
Check and fix due to the defective T/C ass ’y.
Replace the motoror delete fault codeand rediagnosis system.