2003 SSANGYONG MUSSO lock

FRONT DRIVE AXLE 3A-17
1 Front Axle Housing Mounting Bracket
2 Inner Shaft (Left)
3 Bolt...................................................... 55-65 Nm
4 Oil Seal .................................................. Replace
Apply Grease to the Sealing Rib
5 Snap Ring
6 Bearing
7 Snap Ring
8 Oil Drain Plug ....................................... 28-41 Nm
9 Front Axle Housing
10 Breather Nipple 11 Inner Shaft (Right)
12 Pinion Lock Nut ................................ 240-310 Nm
13 Washer
14 Companion Flange
15 Oil Seal .................................................. Replace
Apply Grease to the Sealing Rib
16 Bearing
1 7 Shim
18 Bearing Baffle
1 9 Shim20 Bearing
21 Oil Slinger
22 Drive Pinion
23 Oil Filler Plug ....................................... 28-41 Nm
24 Bolt ...................................................... 39-46 Nm
25 Axle Housing Cover ..............Apply Liquid Gasket
to the Contact Surface
26 Ring Gear
27 Bearing
2 8 Shim
29 Shaft Lock Pin
30 Differential Case
31 Bolt ...................................................... 75-90 Nm
32 Bolt ...................................................... 48-69 Nm
33 Washer
34 Bearing Cap
35 Thrust Washer
36 Side Gear
37 Differential Shaft
38 Differential Pinion
39 Thrust Washer

FRONT DRIVE AXLE 3A-19
5. Unscrew the bearing cap bolts and remove the bearing caps.Pull out the differential carrier assembly. NoticePlace alignment marks on the bearing cap not to change the caps before removal. When pulling out the differential
carrier assembly, be careful not to damage the axle housing.
6. Disassemble the parts of the differential carrier assembly.
7. Remove the drive pinion lock nut. Disassemble the parts of the drive pinion.
Assembly Procedure
1. Clean the all parts and check the followings : Check the ring gear and drive pinion for wear and damage. If damaged, replace it as a set.
Check the bearing for sticks, wear, noise and turning resistance.
Check the side gear, pinion, pinion shaft and thrustwasher for wear and damage.
Check the differential carrier for crack and wear (bearingcontact surface). Check the gear case for crack.

3A-20 FRONT DRIVE AXLE
2. Assemble the parts of the drive pinion.
3. Assemble the parts of the differential carrier.
4. Measure backlash of the side gear and pinion.
5. Install the differential carrier assembly into the axle housing.Notice Be careful not to change the caps. Be sure to keep the original position of the caps.
Tightening Torque of the Lock Nut 240 - 310 Nm
Tightening Torque of the
Ring Gear Bolts 75 - 90 Nm
Standard 0 -
0.05 mm
Tightening Torque of the
Bearing Cap Bolts 48 - 69 Nm

3D-2 REAR DRIVE AXLEFASTENER TIGHTENING SPECIFICATIONS
Application
Inner Bracket Mounting Nut Propeller Shaft to Rear Axle Input ShaftLower Arm Mounting Nut Lower Shock Absorber to Axle Housing Upper Arm Mounting NutStabilizer Bar Mounting BoltLateral Rod Mounting NutDrive Pinion Lock Nut Oil Drain Plug Ring Gear Mounting BoltOil Filler Plug
N 

 m
50 - 65 70 - 80
150 - 180 50 - 65
150 - 180 30 - 45
150 - 180240 - 310 28 - 4275 - 9028 - 42
4.55 4.554.55 4.27 5.863.733.734.89
1.9 L
SEA 80W/90, API GL - 5
M/TA/T (MB) M/T A/T (MB)A/T (BTRA)M/TA/T (MB) A/T (BTRA)
Oil Capacity Oil Specification
Application Description
GENERAL SPECIFICATIONS(CONT'D)
E20 E23 E32
Reduction Ratio

REAR DRIVE AXLE 3D-11
UNIT REPAIR
AXLE HOUSING Preceding Work : Removal of the axle shaft Removal of the axle housing
1 Drive Pinion Lock Nut ......................240-310 Nm
2 Washer
3 Companion Flange
4 Pinion Oil Seal
5 Bearing Slinger
6 Bearing
7 Shim
8 Shim
9 Bearing Cup
10 Breather Nipple
11 Rear Axle Housing
12 Oil Drain Plug ....................................... 28-42 Nm
1 3 Shim
14 Bearing
15 Drive Pinion
16 Bearing Cap 17 Bolt
.................................................... 87-124 Nm
18 Bearing
1 9 Shim
20 Ring Gear
21 Shaft Lock Pin
22 Differential Case
23 Ring Gear Mounting Bolt ......................75-90 Nm
24 Thrust Washer
25 Differential Pinion
26 Thrust Washer
27 Side Gear
28 Differential Shaft
29 Housing Cover
30 Bolt ...................................................... 38-46 Nm
31 Oil Filler Plug ....................................... 28-42 Nm

REAR DRIVE AXLE 3D-13
5. Remove the drive pinion lock nut. Disassemble the parts ofthe drive pinion.
Assembly Procedure
1. Clean the all parts and check the followings. Check the ring gear and drive pinion for wear or damage.
If damaged, replace it as set.
Check the bearing for sticks, wear, noise or turning
resistance.
Check the side gear, pinion, pinion shaft and thrust
washer for wear or damage.
Check the differential carrier for crack or wear (bearing
contact surface). Check the gear case for crack.
2. Assemble the parts of the drive pinion.
3. Assemble the parts of the differential carrier.
Tightening Torque of The Pinion Lock Nut 240 - 310 Nm
Tightening Torque of The
Ring Gear Bolts 75 - 90 Nm

REAR DRIVE AXLE 3D-17
Inspection
Remove the LSD assembly and check the pre-load torque.
If necessary, replace LSD assembly.
Procedure
1. Fix the right shaft of LSD to the special tool (A).
2. Install the special tool (B) to the left shaft and rotate counterclockwise and check the pre-load torque.
Normal Torque 3.6 - 9.0kgm
Notice
If necessary, replace LSD assembly.

SECTION 4A
HYDRAULIC BRAKES
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4A-1
General Specifications . . . . . . . . . . . . . . . . . . 4A-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Noise or Vehicle Vibration When Applied
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Pulls to One Side When Braking . . . . . . . . . . . 4A-2
Poor Braking . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2Increasing Pedal Stroke (Pedal Goes to
Floor) or Brake Dragging . . . . . . . . . . . . . . . 4A-3
Poor Braking of Parking Brake . . . . . . . . . . . . 4A-3 TABLE OF CONTENTS
Component Locator . . . . . . . . . . . . . . . . . . . 4A-4
ABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-4
ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-5
Non-ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . 4A-6
Maintenance and Repair . . . . . . . . . . . . . . . 4A-7
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 4A-7
Bleeding the Brakes . . . . . . . . . . . . . . . . . . . . 4A-7
Brake Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-9
LCRV (Load Conscious Reducing Valve) . . . 4A-12
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting thiscable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCKunless otherwise noted.
Type
Pedal Ratio
Pedal Stroke
Pedal Freeplay Type
Inner Diameter Type
Ratio
Type
I.D. of Caliper Cylinder
Thickness of Brake Pad Thickness of Disc Plate Type
I.D. of Caliper Cylinder
Thickness of Brake Pad Thickness of Disc Plate
Type
Operation
Specification PBR Brake
4.3 : 1
132 mm
23.81 mm
5.0 : 1
60.4 mm

40.5 mm
9.5 mm

Suspended
1 - 4 mm
Tandem Type with Lever Sensor
Vacuum Booster Type
Ventilated Disc 10 mm 24 mm
Rear Wheel Internal Expansion Type Mechanical
SAE J1703, DOT3
SPECIFICATIONS
GENERAL SPECIFICATIONS
Brake Pedal
Master Cylinder Brake Booster Front Brake
Rear Brake
Parking Brake Brake Fluid MANDO Brake
4.3 : 1
138 mm
25.4 mm
5.6 : 1
60 mm
Solid Disc
38.2 mm
10.0 mm 10.4 mm
Application