2003 NISSAN X-TRAIL engine oil

DI-50
WARNING LAMPS

Electrical Components InspectionEKS002HK
OIL PRESSURE SWITCH CHECK
Check the continuity between the terminals of oil pressure switch
and ground.
DIODE CHECK

Check continuity using an ohmmeter.

Diode is functioning properly if test results are as shown in the
figure at left.

Check diodes at the combination meter harness connector
instead of on the combination meter assembly. Refer toDI-34,
"Wiring Diagram — WARN —/LHD Models" or DI-42, "Wiring
Diagram — WARN —/RHD Models" .
NOTE:
Specification may vary depending on the type of tester. Before
performing this inspection, be sure to refer to the instruction
manual for the tester to be used.
Oil pressure kPa (bar, kg/cm2 , psi)Continuity
Engine running More than 29 (0.30, 0.3, 4) No
Engine stopped Less than 29 (0.30, 0.3, 4) Yes
MEL425F
SEL901F

AUDIO
AV-33
C
D
E
F
G
H
I
J
L
MA
B
AV

Trouble DiagnosesEKS00EHY
AUDIO UNIT
Symptom Possible causes Repair order
Audio unit inoperative (no digital display
and no sound from speakers).1. 10A fuse
2. 15A fuse
3. Audio unit ground
4. Audio unit1. Check 10A fuse [No. 4, located
in fuse block (J/B)]. Turn ignition
switch ON and verify that battery
positive voltage is present at ter-
minal 10 (with casette deck) ,3
(without casette deck) of audio
unit.
2. Check 15A fuse (No. 32, located
in fuse and fusible link box) and
verify that battery positive volt-
age is present at terminal 6 (with
casette deck), 9 (without casette
deck) of audio unit.
3. Check audio unit ground.
4. Remove audio unit for repair.
Individual rear speaker is noisy or inopera-
tive.1. Each speaker
2. Output circuit to each speaker1. Check speaker.
2. Check the output circuits to each
speaker between audio unit and
each speaker.
AM/FM stations are weak or noisy. 1. Roof antenna
2. Audio unit ground
3. Audio unit1. Check roof antenna.
2. Check audio unit ground condi-
tion.
3. Remove audio unit for repair.
Audio unit generates noise in AM and FM
modes with engine running.1. Poor audio unit ground
2. Loose or missing ground bonding straps
3. Ignition condenser or rear window defogger
noise suppressor condenser
4. Ignition coil
5. Audio unit1. Check audio unit ground.
2. Check ground bonding straps.
3. Replace ignition condenser or
rear window defogger noise sup-
pressor condenser.
4. Check ignition coil.
5. Remove audio unit for repair.
Audio unit generates noise in AM and FM
modes with accessories on (switch pops
and motor noise).1. Poor audio unit ground
2. Antenna
3. Accessory ground
4. Malfunctioning accessory1. Check audio unit ground.
2. Check antenna.
3. Check accessory ground.
4. Replace accessory.

LT-14
HEADLAMP

Aiming Adjustment for HeadlampEKS003CG
When performing headlamp aiming adjustment, use an aiming machine, aiming wall screen or headlamp
tester. Aimers should be in good repair, calibrated and operated in accordance with respective operation man-
uals.
If any aimer is not available, aiming adjustment can be done as follows:
For details, refer to the regulations in your own country.

Keep all tires inflated to correct pressures.

Place vehicle and tester on one and same flat surface.

See that there is no-load in vehicle (coolant, engine oil filled up to correct level and full fuel tank) other
than the driver (or equivalent weight placed in driver's position).
CAUTION:
Be sure aiming switch is set to “0” when performing aiming adjustment.
LOW BEAM
1. Turn headlamp low beam on.
High beam indicator does not
work.1. Bulb
2. Grounds M27 and M70
3. Open in high beam circuit1. Check bulb in combination meter.
2. Check grounds M27 and M70.
3. Check the wire between lighting switch terminal 9 and
combination meter terminal 20 for an open circuit.
Driving lamp does not operate,
but high beam LH operates.1. 15A fuse
2. Open in driving lamp switch
3. Driving lamp switch circuit
4. Driving lamp relay-2
5. Open in driving lamp relay-2 circuit
6. Grounds E24 and E50
7. Driving lamp relay-1
8. Open in driving lamp relay-1 circuit
9. Open driving lamp circuit
10.Ground R8
11 . B u l b1. Check 15A fuse (No. 38, located in fuse and fusible
link box). Verify battery positive voltage is present at
terminal 3 of driving lamp relay-1.
2. Check the wire between lighting switch terminal 9 and
driving lamp switch terminal 7 for an open circuit.
3. Check driving lamp switch.
4. Check driving lamp relay-2.
5. Check the wire between driving switch terminal 4 and
driving lamp relay-2 terminal 1 for an open circuit.
Check the wire between driving switch terminal 6 and
driving lamp relay-2 terminal 3 for an open circuit.
Check the wire between lighting switch terminal 9 and
driving lamp relay-2 terminal 5 for an open circuit.
Check the wire between driving lamp relay-1 terminal
2 and driving lamp relay-2 terminal 7 for an open cir-
cuit.
6. Check grounds E24 and E50.
7. Check driving lamp relay-1.
8. Check the wire between lighting switch terminal 9 and
driving lamp relay-1 terminal 1 for an open circuit.
9. Check the wire between driving lamp relay-1 terminal
5 and driving lamp terminal 2 for an open circuit.
10.Check ground R8.
11.Check bulbs. Symptom Possible cause Repair order
PKIA5554E

HEADLAMP
LT-15
C
D
E
F
G
H
I
J
L
MA
B
LT

2. Use adjusting screws to perform aiming adjustment.

First tighten the adjusting screw all the way and then make adjustment by loosening the screw.
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check
aiming. Use the aiming chart shown in the figure.

Adjust headlamps so that main axis of light is parallel to cen-
ter line of body and is aligned with point P shown in illustra-
tion.

Figure to the right shows headlamp aiming pattern for driving
on right side of road; for driving on left side of road, aiming
pattern is reversed.

Dotted lines to point P in illustration show center of head-
lamp.

Basic illuminating area for adjustment should be within the
range shown at right. Adjust headlamps accordingly.
CAUTION:
Be sure aiming switch is set to “0” when preforming aiming
adjustment.
Aiming Adjustment for Driving LampEKS00AP6

Turn the aiming adjusting screw to adjust.

For positions of the adjustment screws and direction to turn,
refer to the figures.

When adjusting for right or left side, adjust upper and lower
adjustment screws at the same time.
PREPARATION BEFORE ADJUSTING
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
1. Keep all tires inflated to correct pressures.
2. Place vehicle on level ground.
3. Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position),
coolant, engine oil filled up to correct level, full fuel tank and spare tire, jack, and tools."H" : Horizontal center line of headlamps
"W
L " : Distance between each headlamp center
"L" : 25,000mm (984.25 in)
"C" : 315mm (12.40 in) – 315mm(12.40in)+60mm
(2.36 in)
PKIA3537E
PKIA3394E

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Blower unit ....................... ATC-125, MTC-22, MTC-24
BOOST - Wiring diagram ............... EC-1040, EC-1347
Boring/horning cylinder block(QR20DEQR25DE) .......
EM-103
Brake booster .................................................... BR-23
Brake fluid change ............................................... BR-8
Brake fluid level ................................................. MA-41
Brake fluid level and line check ........................... BR-8
Brake hydraulic line ........................................... BR-10
Brake inspection ................................................ MA-43
Brake lines and cables inspection ..................... MA-41
Brake master cylinder ........................................ BR-14
Brake pedal ......................................................... BR-6
Brake switch ..... EC-380, EC-733, EC-1177, EC-1475
BRK/SW - Wiring diagram EC-381, EC-735, EC-1178,
EC-1476
Bulb specifications .............................................. LT-92
Bumper, front ....................................................... EI-14
Bumper, rear ........................................................ EI-17
C
Camshaft inspection(QR20DEQR25DE) .......... EM-55
Camshaft inspection(YD22DDTi) .................... EM-171
Camshaft position sensor (CMPS) EC-1056, EC-1062,
EC-1363
, EC-1369
Camshaft position sensor (PHASE) .. EC-254, EC-646
Camshaft(QR20DEQR25DE) ........................... EM-53
Camshaft(YD22DDTi) ...................................... EM-170
CAN - Wiring diagram ......... EC-133, EC-580, EC-945,
EC-1269
, LAN-10, LAN-26, LAN-51, LAN-69, LAN-87
CAN (Controller Area Network) ........... BRC-8, LAN-9,
LAN-25
, LAN-50, LAN-68, LAN-86
CAN communication EC-38, EC-132, EC-500, EC-579,
EC-888
, EC-944, EC-1268, AT-32, AT-97, AT-329,
TF-43
, BRC-8, LAN-9, LAN-25, LAN-50, LAN-68,
LAN-86
Canister-See EVAP canister ............. EC-476, EC-868
CHARGE - Wiring diagram .................... SC-13, SC-14
Charging system ................................................ SC-12
Chassis and body maintenance ........................ MA-37
CHIME - Wiring diagram ................ DI-52, DI-55, DI-56
CIGAR - Wiring diagram .................................. WW-27
Cigarette lighter ............................................... WW-27
Circuit breaker ................................................... PG-12
CKPS - Wiring diagram .. EC-947, EC-1046, EC-1052,
EC-1271
, EC-1353, EC-1359
Clearance lamp ........................................ LT-4, LT-60
Clock ................................................................... DI-61
CLOCK - Wiring diagram .................................... DI-61
Closed loop control .............................. EC-35, EC-497
Clutch cover ....................................................... CL-14
Clutch disc ......................................................... CL-14
Clutch master cylinder ......................................... CL-8
Clutch operating cylinder ................................... CL-10
Clutch pedal ......................................................... CL-5
Clutch release bearing ....................................... CL-12
Clutch release mechanism ................................ CL-12
Clutch withdrawal lever ...................................... CL-12
CMPS - Wiring diagram . EC-947, EC-1058, EC-1064,
EC-1271
, EC-1365, EC-1371
Coil spring (rear) ............................................... RSU-8
Collision diagnosis .......................................... SRS-48
Combination meter ............................................... DI-4
Combination switch ............................................. LT-40
Component Location (auto A/C) ......... ATC-35, MTC-4
Compression pressure(QR20DEQR25DE) ..... EM-67
Compression pressure(YD22DDTi) ................ EM-196
Compressor clutch removal and installation .. ATC-146
Compressor special service tool ...................... ATC-14
Condenser ..................................................... ATC-155
Connecting rod bearing clearance(QR20DEQR25DE)
EM-101
Connecting rod bearing clearance(YD22DDTi) EM-232
Connecting rod bushing clearance(YD22DDTi) EM-226
Connecting rod(QR20DEQR25DE) ............... EM-101
Connecting rod(YD22DDTi) .............. EM-223, EM-228
CONSULT for engine ......................... EC-102, EC-551
CONSULT-II for engine ................... EC-926, EC-1251
Control lever (M/T) ............................................. MT-14
Control unit ..................................... ATC-120, MTC-21
Control units (terminal arrangement) ................. PG-72
Controller Area Network (CAN) ........... BRC-8, LAN-9,
LAN-25
, LAN-50, LAN-68, LAN-86
Converter housing installation ......................... AT-523
COOL/F - Wiring diagram EC-352, EC-704, EC-1014,
EC-1322
Coolant replacement(QR20DEQR25DE) ........ MA-20
Coolant replacement(YD22DDTi) ..................... MA-28
Cooling circuit (engine)(QR20DEQR25DE) ....... CO-7
Cooling circuit (engine)(YD22DDTi) ................. CO-29
Cooling fan ............................................ CO-18, CO-36
Cooling fan relay EC-363, EC-715, EC-1024, EC-1331
Coupling sleeve (M/T) ........................... MT-20, MT-25
Cowl top .............................................................. EI-20
Cowl top cover .................................................... EI-20
Crankcase ventilation system .......... EC-888, EC-1219
Crankcase ventilation system - See Positive crankcase
ventilation ........................................... EC-478
, EC-870
Crankshaft position sensor (POS) ..... EC-247, EC-638
Crankshaft position sensor (TDC) EC-1044, EC-1050,
EC-1351
, EC-1357
Crankshaft(QR20DEQR25DE) ........................ EM-83
Cylinder block boring(QR20DEQR25DE) ...... EM-104
Cylinder block boring(YD22DDTi) ................... EM-230
Cylinder block(QR20DEQR25DE) ................... EM-82
Cylinder block(YD22DDTi) .............................. EM-212
Cylinder head bolt tightening(QR20DEQR25DE) ........
EM-69
Cylinder head bolt tightening(YD22DDTi) ....... EM-198
Cylinder head gasket selection(YD22DDTi) ... EM-199
Cylinder head(QR20DEQR25DE) ................... EM-67
Cylinder head(YD22DDTi) .............................. EM-196
D
Data link connector ............................ EC-469
, EC-861
Data link connector for Consult ......... EC-104, EC-553,

IDX-4
ALPHABETICAL INDEX
EC-926, EC-1251
Daytime light system ........................................... LT-20
Daytime running light - See Daytime light system LT-20
DEF - Wiring diagram ....................................... GW-21
Desiccant Assembly ...................................... ATC-156
Diagnosis sensor unit ..................................... SRS-41
Diagnostic trouble code (DTC) ...................... EC-1223
Diagnostic trouble code (DTC) for OBD system EC-19,
EC-54
, EC-482, EC-513, EC-874, EC-894, EC-1205
Diagnostic trouble code (DTC) inspection priority chart
EC-76
, EC-523, EC-904, EC-1230
Differential gear (FF M/T) ..................... MT-23, MT-28
DLC - Wiring diagram ........................ EC-469, EC-861
Door glass ........................................... GW-80, GW-83
Door glass Fitting Adjustment ............. GW-80, GW-83
Door lock ................................................. BL-91, BL-95
Door mirror ........................................................ GW-86
Door trim ............................................................. EI-32
Door, front .......................................................... BL-18
Door, rear ........................................................... BL-18
Drive belt inspection(QR20DEQR25DE) ......... MA-20
Drive belt inspection(YD22DDTi) ...................... MA-27
Drive belt(QR20DEQR25DE) .......................... EM-13
Drive belt(YD22DDTi) ..................................... EM-131
Drive shaft (front) ............................................. FAX-11
Drive shaft (rear) ............................................. RAX-10
Driver air bag .................................................. SRS-30
Dropping resistor (A/T) ...................... AT-160, AT-393
DTC work support ............................................ EC-111
DTRL - Wiring diagram ....................................... LT-20
Dual pressure switch ........ ATC-18, ATC-95, ATC-158
Duct and grilles ............................... ATC-137, MTC-33
E
ECM input/output signal ....................... EC-95
, EC-543
ECM power supply EC-124, EC-282, EC-571, EC-664,
EC-937
, EC-1261
ECM relay ...................................... EC-1110, EC-1399
ECM/PW - Wiring diagram ................. EC-283, EC-665
ECTS - Wiring diagram ...... EC-164, EC-599, EC-983,
EC-1293
EGR function ................ EC-1073, EC-1080, EC-1465
EGR volume control valve ............ EC-1073, EC-1080,
EC-1465
EGRC/V - Wiring diagram ............. EC-1076, EC-1083,
EC-1467
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-290, EC-292,
EC-310
, EC-668, EC-671, EC-690
Electrical load signal circuit ................ EC-456, EC-848
Electrical unit ..................................................... PG-72
Electrical units location ...................................... PG-65
Electronic ignition (EI) system ............. EC-37, EC-499
Engine control circuit diagram EC-93, EC-541, EC-917,
EC-1243
Engine control component parts location .......... EC-88,
EC-536
Engine control module (ECM) ........... EC-279, EC-661, EC-1089
, EC-1091, EC-1378, EC-1380
Engine control system diagram and chart ........ EC-30,
EC-492
, EC-883, EC-1214
Engine coolant temperature sensor (ECTS) ... EC-162,
EC-597
, EC-981, EC-1291
Engine coolant(QR20DEQR25DE) .................... CO-9
Engine coolant(YD22DDTi) .............................. CO-31
Engine fail-safe system ....................... EC-77, EC-524
Engine oil filter replacement(QR20DEQR25DE) .........
MA-25
Engine oil filter replacement(YD22DDTi) MA-33, MA-35
Engine oil precautions .......................................... GI-7
Engine oil replacement(QR20DEQR25DE) ..... MA-23
Engine oil replacement(YD22DDTi) .................. MA-33
Engine oil(QR20DEQR25DE) ............................. LU-7
Engine oil(YD22DDTi) ....................................... LU-20
Engine removal(QR20DEQR25DE) ................ EM-78
Engine removal(YD22DDTi) ........................... EM-208
ETC1 - Wiring diagram ..................... EC-293, EC-673
ETC2 - Wiring diagram ..................... EC-304, EC-684
ETC3 - Wiring diagram ..................... EC-311, EC-691
EVAP canister purge volume control solenoid valve ....
EC-265
, EC-473, EC-809, EC-865
EVAP vapor lines inspection(QR20DEQR25DE) ........
MA-26
Evaporative emission (EVAP) system EC-473, EC-865
Evaporator .................................................... ATC-158
Exhaust manifold(QR20DEQR25DE) .............. EM-23
Exhaust manifold(YD22DDTi) ......................... EM-141
Exhaust system ................................................... EX-2
Exhaust system inspection ..................... EX-2, MA-37
Expansion valve ............................................ ATC-159
Exterior EI-21, EI-22, EI-24, EI-25, EI-26, EI-27, EI-28,
EI-30
, EI-31
F
F/FOG - Wiring diagram ......................... LT-52
, LT-53
F/PUMP - Wiring diagram EC-444, EC-836, EC-1134,
EC-1422
Fan control amp. ............................. ATC-84, ATC-129
Fan switch ....................................................... MTC-18
FIAR - Wiring diagram .................. EC-1117, EC-1406
Final drive (FF M/T) .............................. MT-23, MT-28
Finisher, interior - See Trim ................................ EI-32
Finisher, rear panel ............................................. EI-31
Floor trim ............................................................. EI-38
Flow charts ......................................................... GI-23
Fluid temperature sensor (A/T) ........................ AT-111
Fluorescent leak detector ............................. ATC-160
Flywheel (clutch) ................................................ CL-14
Flywheel runout(QR20DEQR25DE) EM-108, EM-235
Fog lamp, front ................................................... LT-52
Fork rod (M/T) ....................................... MT-22, MT-27
Freeze frame data EC-55, EC-514, EC-895, EC-1223
FRO2 - Wiring diagram ..................... EC-772, EC-787
Front bumper ...................................................... EI-14
Front disc brake ................................................. BR-27
Front door .......................................................... BL-18

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Front Door Trim ................................................... EI-32
Front fog lamp .................................................... LT-52
Front passenger air bag .................................. SRS-35
Front seat .......................................................... SE-24
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner .... SB-2, SRS-3, SRS-40
Front side air bag ............................................. SRS-37
Front suspension ............................................... FSU-5
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FRPS - Wiring diagram .................... EC-999, EC-1309
FTS - Wiring diagram ...................... EC-994, EC-1304
FUEL - Wiring diagram ...................... EC-218, EC-225
Fuel check valve ................................ EC-473, EC-865
Fuel cut control (at no load high engine speed) EC-38,
EC-500
, EC-887, EC-1218
Fuel filler lid ...................................................... BL-103
Fuel filter .......................................... EC-890, EC-1221
Fuel filter replacement(QR20DEQR25DE) .......... FL-4
Fuel filter replacement(YD22DDTi) ....... FL-17, MA-31
Fuel gauge ............................................................ DI-4
Fuel injection control system ........... EC-885, EC-1216
Fuel injection system ......................... EC-216, EC-223
Fuel injector adjustment resistor .... EC-1115, EC-1404
Fuel injector and fuel tube(QR20DEQR25DE) . EM-32
Fuel injector and fuel tube(YD22DDTi) ............ EM-157
Fuel line inspection(QR20DEQR25DE) . FL-3, MA-23
Fuel line inspection(YD22DDTi) ............ FL-16, MA-31
Fuel pressure check ............................ EC-48, EC-510
Fuel pressure release .......................... EC-48, EC-510
Fuel pump .......... EC-443, EC-835, EC-890, EC-1127,
EC-1416
Fuel pump and gauge(QR20DEQR25DE) .......... FL-4
Fuel rail pressure sensor ................. EC-997, EC-1307
Fuel system(QR20DEQR25DE) .......................... FL-3
Fuel system(YD22DDTi) ..................................... FL-16
Fuel tank(QR20DEQR25DE) ............................ FL-11
Fuel tank(YD22DDTi) ......................................... FL-23
Fuel temperature sensor ................. EC-993, EC-1303
Fuse ................................................................... PG-12
Fuse and fusible link box ................................... PG-76
Fusible link ......................................................... PG-12
G
Gauges ................................................................. DI-4
Gear components (M/T) ....................... MT-20, MT-25
Generator .......................................................... SC-12
Generator - See Alternator ................................ SC-12
Generic scan tool (GST) .................... EC-112, EC-931
Glass .................................................. GW-80, GW-83
GLOW - Wiring diagram EC-1070, EC-1170, EC-1458
Glow plug ....................................... EC-1169, EC-1457
Glow plug(YD22DDTi) ..................................... EM-152
Glow relay ...................... EC-1069, EC-1169, EC-1457
GPS antenna ..................................................... AV-43
Grille - See Exterior ............................................. EI-19
Ground distribution ............................................ PG-13
H
H/AIM - Wiring diagram ...................................... LT-29
H/LAMP - Wiring diagram ........................... LT-4, LT-7
H/MIRROR - Wiring diagram ............................ GW-21
Harness connector ............................................. PG-70
Harness layout ................................................... PG-30
Headlamp ............................................................. LT-4
Headlamp aiming control .................................... LT-29
Headlamp leveler - See Headlamp aiming control .......
LT-29
Headlamp washer ............................................ WW-20
Headlining - See Roof trim .................................. EI-39
Heated oxygen sensor 1 .... EC-176, EC-183, EC-193,
EC-318
, EC-324, EC-611, EC-618, EC-786
Heated oxygen sensor 1 heater ......... EC-138, EC-771
Heated oxygen sensor 2 .... EC-201, EC-208, EC-330,
EC-338
, EC-792
Heated oxygen sensor 2 heater ......... EC-144, EC-776
Heated seat ........................................... SE-18, SE-21
HEATER - Wiring diagram ................................ MTC-6
Heater and cooling unit (Heater core) ............ ATC-131
Heater mirror ..................................................... GW-21
Heater system - Wiring diagram ....................... MTC-6
Heater unit (heater core) .. ATC-136, MTC-27, MTC-30
HFC134a (R134a) system precaution ............... ATC-4
HFC134a (R134a) system service procedure ATC-141
HFC134a (R134a) system service tools .......... ATC-15
HFC134a system service equipment precaution ..........
ATC-10
HO2S1 - Wiring diaram ...... EC-178, EC-186, EC-196,
EC-613
, EC-620
HO2S1H - Wiring diagram ............................... EC-140
HO2S2 - Wiring diagram .... EC-203, EC-211, EC-333,
EC-341
HO2S2H - Wiring diagram ............................... EC-146
Hood .................................................................. BL-12
Horn ................................................................. WW-25
HORN - Wiring diagram ................................... WW-25
How to erase DTC ........................... EC-514, EC-1223
How to erase DTC for OBD system ..... EC-63, EC-895
I
IATS - Wiring diagram ...... EC-158
, EC-977, EC-1287
IATSEN - Wiring diagram ................................ EC-782
Identification ...................................... ATC-12, ATC-13
Idle air volume learning ........................ EC-46, EC-508
Idle speed ............. EC-79, EC-526, EC-905, EC-1231
Ignition coil ......................................... EC-417, EC-798
Ignition coil(QR20DEQR25DE) ....................... EM-29
Ignition control system ....................... EC-417, EC-798
Ignition timing ....................................... EC-79, EC-526
IGNSYS - Wiring diagram .................. EC-418, EC-799
ILL - Wiring diagram ........................................... LT-66
Illumination .......................................................... LT-66
In vehicle sensor ........... ATC-111, ATC-113, ATC-122
INJE/PW - Wiring diagram ............. EC-1158, EC-1446
INJECT - Wiring diagram . EC-429, EC-821, EC-1008,

IDX-6
ALPHABETICAL INDEX
EC-1124, EC-1163, EC-1317, EC-1413, EC-1451
Injection nozzle(YD22DDTi) ........................... EM-157
Injector ............................................... EC-428, EC-820
Input shaft (FF M/T) .............................. MT-20, MT-25
Intake air temperature sensor ........... EC-156, EC-781,
EC-976
, EC-1286
Intake door control linkage adjustment ............ ATC-81
Intake door motor ATC-79, ATC-128, MTC-11, MTC-26
Intake manifold(QR20DEQR25DE) ................. EM-17
Intake manifold(YD22DDTi) ............................ EM-136
Intake sensor ................................................. ATC-117
Intake valve timing control ................. EC-135, EC-582
Intake valve timing control solenoid valve ....... EC-286
Interior ....................... EI-32, EI-34, EI-35, EI-38, EI-39
Interior lamp ........................................................ LT-76
Interior lamp on-off control ...................... LT-76, LT-77
ISO 15031-5 Mode 1 - 9 ...................... EC-51, EC-892
IVC - Wiring diagram ....................................... EC-287
J
Joint connector (J/C) .......................................... PG-75
K
Keyless entry system - See Multi-remote control system
BL-74
Knock sensor (KS) ............................. EC-242, EC-633
KS - Wiring diagram ........................... EC-243, EC-634
L
LAN system circuit ........................................... ATC-69
License lamp ....................................................... LT-47
Line pressure test (A/T) ....................... AT-68, AT-260
Liquid gasket application ......................... LU-3, LU-17
Liquid gasket application(QR20DEQR25DE) ... EM-6,
EM-123
, CO-3, CO-25
LOAD - Wiring diagram ...................... EC-457, EC-849
Location of electrical units ................................. PG-65
Lock, door ............................................... BL-91, BL-95
Lubricant (R134a) A/C ........................ ATC-5, ATC-24
Lubrication circuit (engine)(QR20DEQR25DE) .. LU-5
Lubrication circuit (engine)(YD22DDTi) ............. LU-19
Lubrication oil A/C .......................................... ATC-164
Lubrication-locks, hinges and hood latches ...... MA-45
M
M/T major overhaul ............................... MT-28
, MT-37
M/T oil replacement ........................................... MT-11
M/T removal and installation .............................. MT-17
MAFS - Wiring diagram ..... EC-151, EC-592, EC-965,
EC-972
, EC-1282
Magnet clutch ................................. ATC-88, ATC-146
MAIN - Wiring diagram ...... EC-124, EC-571, EC-938,
EC-1262
Mainshaft (M/T) ..................................... MT-20, MT-25
Maintenance (engine)(YD22DDTi) ................... MA-27
Major overhaul (Transfer) .................................. TF-57
Malfunction indicator (MI) .... EC-64, EC-516, EC-896,
EC-1224
Mass air flow sensor (MAFS) ........... EC-149, EC-590,
EC-963
, EC-970, EC-1280
Master cylinder (brake) ...................................... BR-14
Master cylinder (clutch) ........................................ CL-8
Meter ..................................................................... DI-4
METER - Wiring diagram ......................... DI-14, DI-17
MIL/DL - Wiring diagram ............... EC-1202, EC-1498
MIRROR - Wiring diagram ............................... GW-87
Mirror defogger ................................................ GW-21
Mirror, door ...................................................... GW-86
Mirror, out side ................................................. GW-86
Misfire .............................................................. EC-237
Mode door control linkage adjustment ........... ATC-75,
ATC-134
, MTC-9, MTC-31
Mode door motor ............................ ATC-73, ATC-134
Molding - See Exterior ................... EI-22, EI-24, EI-25
Mud guard - See Exterior .................................... EI-24
MULTI - Wiring diagram ..................................... BL-77
Multiport fuel injection (MFI) system ... EC-34, EC-496
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system ............................... BL-74
N
NATS - Wiring diagram .................................... BL-111
NATS (Nissan anti-theft system) ..................... BL-108
NATS (Nissan anti-theft system) precautions ....... GI-3
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (Transfer) ........................... TF-8
O
Oil cooler (engine)(QR20DEQR25DE) ............. LU-11
Oil cooler (engine)(YD22DDTi) .......................... LU-28
Oil filter(QR20DEQR25DE) .............................. LU-10
Oil filter(YD22DDTi) ........................................... LU-23
Oil pan (engine)(QR20DEQR25DE) ................ EM-25
Oil pan (engine)(YD22DDTi) ........................... EM-147
Oil pressure (engine)(QR20DEQR25DE) ........... LU-7
Oil pressure (engine)(YD22DDTi) ...................... LU-20
Oil pump (engine)(QR20DEQR25DE) .............. LU-13
Oil pump (engine)(YD22DDTi) ........................... LU-30
Oil seal replacement (engine)(QR20DEQR25DE) ......
EM-44
, EM-67, EM-82
On board diagnostic system . EC-51, EC-513, EC-892
Operating cylinder (clutch) ................................. CL-10
Out side mirror ................................................. GW-86
Overdrive control switch .................... AT-240, AT-327
Overheat ........... EC-348, EC-700, EC-1011, EC-1320
Oversize piston(QR20DEQR25DE) ............... EM-104
Oversize piston(YD22DDTi) ........................... EM-230
P
Park/Neutral position switch EC-373
, EC-725, EC-816,
EC-1182
, EC-1479