2003 NISSAN X-TRAIL high beam

LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION
A
B
LT

LIGHTING SYSTEM
PRECAUTION ............................................................ 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precaution ................................................................ 3
Wiring Diagrams and Trouble Diagnosis .................. 3
HEADLAMP ................................................................ 4
System Description .................................................. 4
DESCRIPTION ...................................................... 4
LOW BEAM OPERATION ..................................... 4
HIGH BEAM OPERATION/FLASH-TO-PASS
OPERATION ......................................................... 4
DRIVING LAMP OPERATION .............................. 4
Schematic ................................................................ 6
Wiring Diagram — H/LAMP — ................................. 7
LHD MODELS ....................................................... 7
RHD MODELS .................................................... 10
Trouble Diagnoses ................................................. 13
Aiming Adjustment for Headlamp ........................... 14
LOW BEAM ......................................................... 14
Aiming Adjustment for Driving Lamp ...................... 15
PREPARATION BEFORE ADJUSTING .............. 15
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 16
ADJUSTING ........................................................ 16
Bulb Replacement for Headlamp and Clearance
lamp ....................................................................... 16
HEAD LAMP ....................................................... 16
CLEARANCE LAMP ........................................... 16
Bulb Replacement for Driving Lamp ...................... 17
Removal and Installation for Headlamp ................. 17
REMOVAL ........................................................... 17
INSTALLATION ................................................... 17
Removal and Installation for Driving Lamp ............ 18
REMOVAL ........................................................... 18
INSTALLATION ................................................... 18
Removal and Installation for Driving Lamp Switch ... 19
HEADLAMP - DAYTIME LIGHT SYSTEM - ............. 20
System Description ................................................ 20DESCRIPTION .................................................... 20
HEADLAMP OPERATION (DAYTIME LIGHT
CANCEL OPERATION) ....................................... 20
DAYTIME LIGHT OPERATION ........................... 20
DRIVING LAMP OPERATION ............................. 20
Schematic ............................................................... 22
Wiring Diagram -DTRL- .......................................... 23
Trouble Diagnoses ................................................. 28
DAYTIME LIGHT CONTROL UNIT INSPECTION
TABLE ................................................................. 28
Bulb Replacement .................................................. 28
Aiming Adjustment .................................................. 28
Removal and Installation ........................................ 28
HEADLAMP AIMING CONTROL ............................. 29
Wiring Diagram -H/AIM- ......................................... 29
Removal and Installation ........................................ 30
Switch Circuit Inspection ........................................ 30
TURN SIGNAL AND HAZARD WARNING LAMPS ... 31
System Description ................................................. 31
TURN SIGNAL OPERATION .............................. 31
HAZARD LAMP OPERATION ............................. 31
Wiring Diagram — TURN — ................................... 33
LHD MODELS ..................................................... 33
RHD MODELS .................................................... 35
Trouble Diagnoses ................................................. 37
Electrical Components Inspection .......................... 37
COMBINATION FLASHER UNIT CHECK ........... 37
Bulb Replacement .................................................. 38
FRONT TURN SIGNAL LAMP ............................ 38
SIDE TURN SIGNAL LAMP ................................ 38
REAR TURN SIGNAL LAMP .............................. 38
Removal and Installation for Front Turn Signal Lamp ... 38
REMOVAL ........................................................... 38
INSTALLATION ................................................... 38
Removal and Installation for Side Turn Signal Lamp ... 38
Removal and Installation for Rear Turn Signal Lamp ... 39
LIGHTING AND TURN SIGNAL SWITCH ................ 40
Removal and Installation ........................................ 40
Switch Circuit Inspection ........................................ 40

LT-4
HEADLAMP

HEADLAMPPFP:26010
System Description EKS003CD
DESCRIPTION
The headlamps are controlled by the lighting switch which is built into the combination switch.
Power is supplied at all times

through 15A fuse (No. 40, located in the fuse and fusible link box)

to lighting switch terminal 8

through 15A fuse (No. 41, located in the fuse and fusible link box)

to lighting switch terminal 5

through 15A fuse (No. 38, located in the fuse and fusible link box)

to driving lamp relay terminal 3.
LOW BEAM OPERATION
When the lighting switch is turned to the 2ND position and placed in LOW position, power is supplied

from lighting switch terminal 10

to headlamp LH terminal 3

from lighting switch terminal 7

to headlamp RH terminal 3
Each headlamp terminal 2 supplies ground through grounds E24 and E50.
With power and ground supplied, the low beams will illuminate.
HIGH BEAM OPERATION/FLASH-TO-PASS OPERATION
When the lighting switch is turned to the 2ND position and placed in HIGH position or PASS position, power is
supplied

from lighting switch terminal 6

to headlamp RH terminal 1

from lighting switch terminal 9

to headlamp LH terminal 1and

to combination meter terminal 20 for the HIGH BEAM indicator.
Ground is supplied

to combination meter terminal 19 through grounds M27 and M70.

to each headlamp terminal 2 through grounds E24 and E50.
With power and ground supplied, the high beams and the HIGH BEAM indicator illuminate.
DRIVING LAMP OPERATION
To turn the driving lamp on, push the driving lamp switch when the lighting switch is turned to the 2ND position
and placed in HIGH position or PASS position, power is supplied

from lighting switch terminal 9

to headlamp LH terminal 1

to driving lamp relay-1 terminal 1

to driving lamp switch terminal 7

to combination meter terminal 20 for the HIGH BEAM indicator

to driving lamp relay-2 terminal 5

to driving lamp relay-2 terminal 3

through driving lamp switch terminal 6

from driving lamp relay-1 terminal 5

to driving lamp LH and RH terminal 2
Ground is supplied

to driving lamp relay-1 terminal 2, through driving lamp relay-2 terminal 7

to driving lamp relay-2 terminal 6, through grounds E24 and E50

to driving lamp switch terminal 4, through driving lamp relay-2 terminal 1

HEADLAMP
LT-5
C
D
E
F
G
H
I
J
L
MA
B
LT


to driving lamp relay-2 terminal 2, through grounds E24 and E50

to driving lamp LH terminal 1, through ground R8

to driving lamp RH terminal 1 and 3, through ground R8

to combination meter terminal 19, through grounds M27 and M70

to each headlamp terminal 2, through grounds E24 and E50.
With power and ground supplied, the high beams, driving lamp and the HIGH BEAM indicator illuminate.

HEADLAMP
LT-13
C
D
E
F
G
H
I
J
L
MA
B
LT

Trouble Diagnoses EKS003CF
Symptom Possible cause Repair order
Headlamp LH do not operate.1. Bulb
2. Grounds E24 and E50
3. 15A fuse
4. Lighting switch1. Check bulb.
2. Check grounds E24 and E50.
3. Check 15A fuse (No. 40, located in fuse and fusible
link box). Verify battery positive voltage is present at
terminal 8 of lighting switch.
4. Check lighting switch.
Headlamp RH do not operate.1. Bulb
2. Grounds E24 and E50
3. 15A fuse
4. Lighting switch1. Check bulb.
2. Check grounds E24 and E50.
3. Check 15A fuse (No. 41, located in fuse and fusible
link box). Verify battery positive voltage is present at
terminal 5 of lighting switch.
4. Check lighting switch.
High beam LH do not operate,
but low beam LH operates.1. Bulb
2. Open in high beam LH circuit
3. Lighting switch1. Check bulbs.
2. Check the wire between lighting switch terminal 9 and
headlamp LH terminal 1 for an open circuit.
3. Check lighting switch.
Low beam LH does not operate,
but high beam LH operates.1. Bulb
2. Open in low beam LH circuit
3. Lighting switch1. Check bulb.
2. Check the wire between lighting switch terminal 10
and headlamp LH terminal 3 for an open circuit.
3. Check lighting switch.
High beam RH do not operate,
but low beam RH operates.1. Bulb
2. Open in high beam RH circuit
3. Lighting switch1. Check bulbs.
2. Check the wire between lighting switch terminal 6 and
headlamp RH terminal 1 for an open circuit.
3. Check lighting switch.
Low beam RH does not operate,
but high beam RH operates.1. Bulb
2. Open in low beam RH circuit
3. Lighting switch1. Check bulb.
2. Check the wire between lighting switch terminal 7 and
headlamp RH terminal 3 for an open circuit.
3. Check lighting switch.

LT-14
HEADLAMP

Aiming Adjustment for HeadlampEKS003CG
When performing headlamp aiming adjustment, use an aiming machine, aiming wall screen or headlamp
tester. Aimers should be in good repair, calibrated and operated in accordance with respective operation man-
uals.
If any aimer is not available, aiming adjustment can be done as follows:
For details, refer to the regulations in your own country.

Keep all tires inflated to correct pressures.

Place vehicle and tester on one and same flat surface.

See that there is no-load in vehicle (coolant, engine oil filled up to correct level and full fuel tank) other
than the driver (or equivalent weight placed in driver's position).
CAUTION:
Be sure aiming switch is set to “0” when performing aiming adjustment.
LOW BEAM
1. Turn headlamp low beam on.
High beam indicator does not
work.1. Bulb
2. Grounds M27 and M70
3. Open in high beam circuit1. Check bulb in combination meter.
2. Check grounds M27 and M70.
3. Check the wire between lighting switch terminal 9 and
combination meter terminal 20 for an open circuit.
Driving lamp does not operate,
but high beam LH operates.1. 15A fuse
2. Open in driving lamp switch
3. Driving lamp switch circuit
4. Driving lamp relay-2
5. Open in driving lamp relay-2 circuit
6. Grounds E24 and E50
7. Driving lamp relay-1
8. Open in driving lamp relay-1 circuit
9. Open driving lamp circuit
10.Ground R8
11 . B u l b1. Check 15A fuse (No. 38, located in fuse and fusible
link box). Verify battery positive voltage is present at
terminal 3 of driving lamp relay-1.
2. Check the wire between lighting switch terminal 9 and
driving lamp switch terminal 7 for an open circuit.
3. Check driving lamp switch.
4. Check driving lamp relay-2.
5. Check the wire between driving switch terminal 4 and
driving lamp relay-2 terminal 1 for an open circuit.
Check the wire between driving switch terminal 6 and
driving lamp relay-2 terminal 3 for an open circuit.
Check the wire between lighting switch terminal 9 and
driving lamp relay-2 terminal 5 for an open circuit.
Check the wire between driving lamp relay-1 terminal
2 and driving lamp relay-2 terminal 7 for an open cir-
cuit.
6. Check grounds E24 and E50.
7. Check driving lamp relay-1.
8. Check the wire between lighting switch terminal 9 and
driving lamp relay-1 terminal 1 for an open circuit.
9. Check the wire between driving lamp relay-1 terminal
5 and driving lamp terminal 2 for an open circuit.
10.Check ground R8.
11.Check bulbs. Symptom Possible cause Repair order
PKIA5554E

LT-20
HEADLAMP - DAYTIME LIGHT SYSTEM -

HEADLAMP - DAYTIME LIGHT SYSTEM -PFP:26010
System DescriptionEKS003BB
DESCRIPTION
The headlamp system on vehicles for North Europe contains a daytime light control unit. The unit activates the
following whenever the engine is running with the lighting switch in the OFF position:

Low beam headlamps

Parking, license, tail and illumination lamps
Power is supplied at all times

through 10A fuse (No. 31, located in the fuse and fusible link box)

to daytime light control unit terminal 1 and

to lighting switch terminal 11.
Power is also supplied at all times

through 15A fuse (No. 41, located in the fuse and fusible link box)

to daytime light control unit terminal 3 and

to lighting switch terminal 5.
Power is also supplied at all times

through 15A fuse (No. 40, located in the fuse and fusible link box)

to daytime light control unit terminal 2 and

to lighting switch terminal 8.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 13, located in the fuse block (J/B)]

to daytime light control unit terminal 7.
With the ignition switch in the START position, power is supplied

through 10A fuse [No. 7, located in the fuse block (J/B)]

to daytime light control unit terminal 6.
HEADLAMP OPERATION (DAYTIME LIGHT CANCEL OPERATION)
When the lighting switch is turned to the 1st or 2nd position, power is supplied

through lighting switch terminal 12

to daytime light control unit terminal 11.
Then daytime light will be canceled. And the lighting system operation will be the same as no daytime light
system.
DAYTIME LIGHT OPERATION
With the engine running and the lighting switch in the OFF position, power is supplied

from alternator terminal 3

to daytime light control unit terminal 8,

through daytime light control unit terminal 5

to terminal 3 of headlamp LH,

through daytime light control unit terminal 4

to terminal 3 of headlamp RH and

through daytime light control unit terminal 10

to tail lamp and illumination.
Ground is supplied to terminal 2 of each headlamp through body grounds E24 and E50.
DRIVING LAMP OPERATION
To turn the driving lamp on, push the driving lamp switch when the lighting switch is turned to the 2ND position
and placed in HIGH position or PASS position, power is supplied

from lighting switch terminal 9

to headlamp LH terminal 1

to driving lamp relay-1 terminal 1

HEADLAMP - DAYTIME LIGHT SYSTEM -
LT-21
C
D
E
F
G
H
I
J
L
MA
B
LT


to driving lamp switch terminal 7

to combination meter terminal 20 for the HIGH BEAM indicator

to driving lamp relay-2 terminal 5

to driving lamp relay-2 terminal 3

through driving lamp switch terminal 6

from driving lamp relay-1 terminal 5

to driving lamp LH and RH terminal 2.
Ground is supplied

to driving lamp relay-1terminal 2, through driving lamp relay-2 terminal 7

to driving lamp relay-2 terminal 6, through grounds E24 and E50

to driving lamp switch terminal 4, through driving lamp relay-2 terminal 1

to driving lamp relay-2 terminal 2, through grounds E24 and E50

to driving lamp LH terminal 1, through ground R8

to driving lamp RH terminal 1 and 3, through ground R8

to combination meter terminal 19, through grounds M27 and M70

to each headlamp terminal 2, through grounds E24 and E50.
With power and ground supplied, the high beams, driving lamp and the HIGH BEAM indicator illuminate.