2003 NISSAN X-TRAIL oil pressure

GI-6
PRECAUTIONS

CAUTION:

Do not use home heating oil, gasoline or other alternate fuels in your diesel engine. The use of
those can cause engine damage.

Do not use summer fuel at temperatures below –7°C (20°F). The cold temperatures will cause wax
to form in the fuel. As a result, it may prevent the engine from running smoothly.

Do not add gasoline or other alternate fuels to diesel fuel.
Precautions for Multiport Fuel Injection System or Engine Control SystemEAS000FT

Before connecting or disconnecting any harness connector for
the multiport fuel injection system or ECM:
Turn ignition switch to “OFF” position.
Disconnect negative battery terminal.
Otherwise, there may be damage to ECM.

Before disconnecting pressurized fuel line from fuel pump to
injectors, be sure to release fuel pressure.

Be careful not to jar components such as ECM and mass air
flow sensor.
Precautions for Turbocharger (If Equipped)EAS000FU
The turbocharger turbine revolves at extremely high speeds and
becomes very hot. Therefore, it is essential to maintain a clean sup-
ply of oil flowing through the turbocharger and to follow all required
maintenance instructions and operating procedures.

Always use the recommended oil. Follow the instructions for
proper time to change the oil and proper oil level.

Avoid accelerating engine to a high rpm immediately after start-
ing.

If engine had been operating at high rpm for an extended period
of time, let it idle for a few minutes prior to shutting if off.
Precautions for HosesEAS000FV
HOSE REMOVAL AND INSTALLATION

To prevent damage to rubber hose, do not pry off rubber hose
with tapered tool or screwdriver.

To reinstall the rubber hose securely, make sure that hose inser-
tion length and orientation is correct. (If tube is equipped with
hose stopper, insert rubber hose into tube until it butts up
against hose stopper.)
SGI787
SGI292
SMA019D
SMA020D

EM-2 ROCKER COVER ..................................................... 42
Removal and Installation ........................................ 42
REMOVAL ........................................................... 42
INSTALLATION .................................................... 43
TIMING CHAIN .......................................................... 44
Removal and Installation ........................................ 44
REMOVAL ........................................................... 44
INSPECTION AFTER REMOVAL ........................ 48
INSTALLATION .................................................... 49
CAMSHAFT ............................................................... 53
Removal and Installation ........................................ 53
REMOVAL ........................................................... 53
INSPECTION AFTER REMOVAL ........................ 55
INSTALLATION .................................................... 58
Valve Clearance ...................................................... 61
INSPECTION ....................................................... 61
ADJUSTMENT .................................................... 62
OIL SEAL .................................................................. 64
Removal and Installation of Valve Oil Seal ............. 64
REMOVAL ........................................................... 64
INSTALLATION .................................................... 64
Removal and Installation of Front Oil Seal ............. 64
REMOVAL ........................................................... 64
INSTALLATION .................................................... 65
Removal and Installation of Rear Oil Seal .............. 65
REMOVAL ........................................................... 65
INSTALLATION .................................................... 65
CYLINDER HEAD ..................................................... 67
On-Vehicle Service ................................................. 67
CHECKING COMPRESSION PRESSURE ......... 67
Removal and Installation ........................................ 68
REMOVAL ........................................................... 68
INSPECTION AFTER REMOVAL ........................ 69
INSTALLATION .................................................... 69
Disassembly and Assembly .................................... 71
DISASSEMBLY ................................................... 71
ASSEMBLY ......................................................... 72
Inspection After Disassembly ................................. 73
VALVE DIMENSIONS .......................................... 73
VALVE GUIDE CLEARANCE .............................. 73
VALVE GUIDE REPLACEMENT ......................... 74
VALVE SEAT CONTACT ..................................... 75
VALVE SEAT REPLACEMENT ........................... 75
VALVE SPRING SQUARENESS ......................... 77
VALVE SPRING DIMENSIONS AND VALVE
SPRING PRESSURE LOAD ............................... 77
ENGINE ASSEMBLY ................................................ 78
Removal and Installation ........................................ 78
REMOVAL ........................................................... 78
INSTALLATION .................................................... 81
INSPECTION AFTER INSTALLATION ................ 81
CYLINDER BLOCK ................................................... 82
Disassembly and Assembly .................................... 82
DISASSEMBLY ................................................... 83
ASSEMBLY ......................................................... 87
How to Select Piston and Bearing .......................... 92
DESCRIPTION .................................................... 92
HOW TO SELECT PISTON ................................. 92
HOW TO SELECT CONNECTING ROD BEAR-ING ....................................................................... 93
HOW TO SELECT MAIN BEARING .................... 95
Inspection After Disassembly .................................. 99
CRANKSHAFT END PLAY .................................. 99
CONNECTING ROD SIDE CLEARANCE ........... 99
PISTON TO PISTON PIN OIL CLEARANCE ....... 99
PISTON RING SIDE CLEARANCE ...................100
PISTON RING END GAP ..................................100
CONNECTING ROD BEND AND TORSION .....101
CONNECTING ROD BIG END DIAMETER ......101
CONNECTING ROD BUSHING OIL CLEAR-
ANCE .................................................................101
CYLINDER BLOCK DISTORTION ....................102
MAIN BEARING HOUSING INNER DIAMETER .103
PISTON TO CYLINDER BORE CLEARANCE ..103
CRANKSHAFT MAIN JOURNAL DIAMETER ...104
CRANKSHAFT PIN JOURNAL DIAMETER ......105
OUT-OF-ROUND AND TAPER OF CRANK-
SHAFT ...............................................................105
CRANKSHAFT RUNOUT ..................................105
CONNECTING ROD BEARING OIL CLEAR-
ANCE .................................................................105
MAIN BEARING OIL CLEARANCE ...................106
MAIN BEARING CRUSH HEIGHT ....................107
CONNECTING ROD BEARING CRUSH
HEIGHT .............................................................107
LOWER CYLINDER BLOCK MOUNTING BOLT
OUTER DIAMETER ...........................................107
CONNECTING ROD BOLT OUTER DIAMETER .107
FLYWHEEL DEFLECTION (M/T MODELS) ......108
MOVEMENT AMOUNT OF FLYWHEEL (M/T
MODELS) ...........................................................108
SERVICE DATA AND SPECIFICATIONS (SDS) ....109
Standard and Limit ................................................109
GENERAL SPECIFICATIONS ...........................109
DRIVE BELT ......................................................109
INTAKE MANIFOLD AND EXHAUST MANI-
FOLD .................................................................109
SPARK PLUG ....................................................109
CYLINDER HEAD ..............................................109
VALVE ................................................................110
CAMSHAFT AND CAMSHAFT BEARING .........113
CYLINDER BLOCK ............................................114
PISTON, PISTON RING AND PISTON PIN ......115
CONNECTING ROD ..........................................116
CRANKSHAFT ...................................................116
MAIN BEARING .................................................118
CONNECTING ROD BEARING .........................119
Tightening Torque .................................................119
YD22DDTi
PRECAUTIONS .......................................................122
Precautions for Draining Engine Coolant ..............122
Precautions for Disconnecting Fuel Piping ...........122
Precautions for Removal and Disassembly ..........122
Precautions for Inspection, Repair and Replace-
ment ......................................................................122
Precautions for Assembly and Installation ............122

EM-3
C
D
E
F
G
H
I
J
K
L
M
EMA
Parts Requiring Angle Tightening ......................... 122
Precautions For Liquid Gasket ............................. 123
REMOVAL OF LIQUID GASKET ...................... 123
LIQUID GASKET APPLICATION PROCEDURE . 123
PREPARATION ....................................................... 124
Special Service Tools ........................................... 124
Commercial Service Tools .................................... 127
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ............................................ 129
NVH Troubleshooting — Engine Noise ................ 129
Use the Chart Below to Help You Find the Cause
of the Symptom. ................................................... 130
DRIVE BELTS ......................................................... 131
Checking Drive Belts ............................................ 131
Tension Adjustment .............................................. 131
A/C COMPRESSOR BELT ............................... 132
ALTERNATOR AND WATER PUMP BELT ....... 132
Removal and Installation ...................................... 132
REMOVAL ......................................................... 132
INSTALLATION ................................................. 132
AIR CLEANER AND AIR DUCT ............................. 133
Removal and Installation ...................................... 133
REMOVAL ......................................................... 133
INSTALLATION ................................................. 133
CHANGING AIR CLEANER FILTER ................. 134
CHARGE AIR COOLER ......................................... 135
Removal and Installation ...................................... 135
REMOVAL ......................................................... 135
INSPECTION AFTER REMOVAL ..................... 135
INSTALLATION ................................................. 135
INTAKE MANIFOLD ............................................... 136
Removal and Installation ...................................... 136
REMOVAL ......................................................... 136
INSPECTION AFTER REMOVAL ..................... 137
INSTALLATION ................................................. 137
INSPECTION AFTER INSTALLATION ............. 138
CATALYST .............................................................. 139
Removal and Installation ...................................... 139
REMOVAL ......................................................... 139
INSTALLATION ................................................. 140
EXHAUST MANIFOLD AND TURBOCHARGER .. 141
Removal and Installation ...................................... 141
REMOVAL ......................................................... 141
INSTALLATION ................................................. 142
INSPECTION AFTER INSTALLATION ............. 142
Disassembly and Assembly ................................. 143
DISASSEMBLY ................................................. 143
ASSEMBLY ....................................................... 143
INSPECTION AFTER DISASSEMBLY ............. 143
Turbocharger ........................................................ 144
ROTOR SHAFT CLEARANCE ......................... 144
ROTOR SHAFT END PLAY .............................. 144
TURBINE WHEEL ............................................. 145
COMPRESSOR WHEEL .................................. 145
TURBOCHARGER BOOST CONTROL ACTU-
ATOR ................................................................ 145
TROUBLE DIAGNOSIS OF TURBOCHARGER . 146OIL PAN AND OIL STRAINER ...............................147
Removal and Installation ......................................147
REMOVAL .........................................................147
INSPECTION AFTER REMOVAL .....................149
INSTALLATION .................................................149
INSPECTION AFTER INSTALLATION ..............151
GLOW PLUG ..........................................................152
Removal and Installation ......................................152
REMOVAL .........................................................152
INSTALLATION .................................................152
VACUUM PUMP ......................................................153
Removal and Installation ......................................153
INSPECTION BEFORE REMOVAL ..................153
REMOVAL .........................................................153
INSTALLATION .................................................154
INSPECTION AFTER INSTALLATION ..............155
Disassembly and Assembly ..................................155
DISASSEMBLY .................................................155
ASSEMBLY .......................................................156
INJECTION TUBE AND FUEL INJECTOR ............157
Removal and Installation ......................................157
REMOVAL .........................................................157
INSTALLATION .................................................159
INSPECTION AFTER INSTALLATION ..............160
FUEL PUMP ............................................................161
Removal and Installation ......................................161
REMOVAL .........................................................161
INSPECTION AFTER REMOVAL .....................165
INSTALLATION .................................................165
ROCKER COVER ...................................................168
Removal and Installation ......................................168
REMOVAL .........................................................168
INSTALLATION .................................................169
INSPECTION AFTER INSTALLATION ..............169
CAMSHAFT ............................................................170
Removal and Installation ......................................170
REMOVAL .........................................................170
INSPECTION AFTER REMOVAL .....................171
INSTALLATION .................................................174
Valve Clearance ...................................................175
INSPECTION ....................................................175
ADJUSTMENTS ................................................177
SECONDARY TIMING CHAIN ................................180
Removal and Installation ......................................180
REMOVAL .........................................................180
INSPECTION AFTER REMOVAL .....................182
INSTALLATION .................................................182
PRIMARY TIMING CHAIN ......................................185
Removal and Installation ......................................185
REMOVAL .........................................................187
INSPECTION AFTER REMOVAL .....................190
INSTALLATION .................................................190
CYLINDER HEAD ...................................................196
On-Vehicle Service ...............................................196
CHECKING COMPRESSION PRESSURE .......196
Removal and Installation ......................................197
REMOVAL .........................................................197
INSPECTION AFTER REMOVAL .....................198

PRECAUTIONS
EM-5
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

[QR]PRECAUTIONSPFP:00001
Precautions for Drain Engine CoolantEBS00KN0
Drain engine coolant when engine is cooled.
Precautions for Disconnecting Fuel PipingEBS00KN1

Before starting work, make sure no fire or spark producing items are in the work area.

Release fuel pressure before disassembly.

After disconnecting pipes, plug openings to stop fuel leakage.
Precautions for Removal and DisassemblyEBS00KN2

When instructed to use special service tools, use the specified tools. Always be careful to work safely,
avoid forceful or uninstructed operations.

Exercise maximum care to avoid damage to mating or sliding surfaces.

Cover openings of engine system with tape or the equivalent, if necessary, to seal out foreign materials.

Mark and arrange disassembly parts in an organized way for easy troubleshooting and re-assembly.

When loosening nuts and bolts, as a basic rule, start with the one furthest outside, then the one diagonally
opposite, and so on. If the order of loosening is specified, do exactly as specified.
Precautions for Inspection, Repair and ReplacementEBS00KN3
Before repairing or replacing, thoroughly inspect parts. Inspect new replacement parts in the same way, and
replace if necessary.
Precautions for Assembly and InstallationEBS00MRZ

Use torque wrench to tighten bolts or nuts to specification.

When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the
ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is speci-
fied, do exactly as specified.

Replace with new gasket, packing, oil seal or O-ring.

Thoroughly wash, clean, and air-blow each part. Carefully check oil or coolant passages for any restriction
and blockage.

Avoid damaging sliding or mating surfaces. Completely remove foreign materials such as cloth lint or dust.
Before assembly, oil sliding surfaces well.

Release air within route when refilling after draining coolant.

Before starting engine, apply fuel pressure to fuel lines with turning ignition switch “ON” (with engine
stopped). Then make sure there are no leaks at fuel line connections.

After repairing, start engine and increase engine speed to check engine coolant, fuel, engine oil, and
exhaust systems for leakage.
Parts Requiring Angle TighteningEBS00KN5

Use an angle wrench (special service tool: KV10112100) for the final tightening of the following engine
parts.
–Cylinder head bolts
–Lower cylinder block bolts
–Connecting rod cap bolts
–Crankshaft pulley bolt (No angle wrench is required as the bolt flange is provided with notches for angular
tightening)
–Balancer unit

Do not use a torque value for final tightening.

The torque value for these parts are for a preliminary step.

Ensure thread and seat surfaces are clean and coated with engine oil.

CAMSHAFT
EM-53
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

CAMSHAFTPFP:13001
Removal and InstallationEBS00LS2
NOTE:
This section describes removal/installation procedure of camshaft without removing front cover. If front cover
is removed or installed, removal of camshaft bracket (No. 1) is easier before step 8 and installation is easier
after step 3. Regarding removal and installation of front cover, refer to EM-44, "
TIMING CHAIN" .
REMOVAL
1. Release fuel pressure. Refer to EC-48, "FUEL PRESSURE RELEASE" (WITH EURO-OBD) or EC-510,
"FUEL PRESSURE RELEASE" (WITHOUT EURO-OBD).
2. Remove the following parts.

Ignition coil; Refer to EM-29, "IGNITION COIL" .

Rocker cover; Refer to EM-42, "ROCKER COVER" .
3. Remove power steering reservoir tank from bracket to move power steering piping. Refer to PS-34,
"HYDRAULIC LINE" .
1. Camshaft bracket (No. 2 to 5) 2. Seal washer 3. Camshaft bracket (No. 1)
4. Front cover 5. Chain guide 6. Chain tensioner
7. Spring 8. Chain tensioner plunger 9. O-ring
10. Oil ring 11. O-ring 12.Intake valve timing control solenoid
valve
13. Intake valve timing control cover 14. Camshaft sprocket (INT) 15. Camshaft sprocket (EXH)
16. O-ring 17. Valve lifter 18. Camshaft (INT)
19. Camshaft (EXH) 20. O-ring 21. Camshaft position sensor (PHASE)
PBIC2184E

CYLINDER HEAD
EM-67
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

CYLINDER HEADPFP:11041
On-Vehicle ServiceEBS00KNP
CHECKING COMPRESSION PRESSURE
1. Warm up engine thoroughly. Then, stop it.
2. Release fuel pressure by “Without CONSULT-II”. Refer to EC-48, "
FUEL PRESSURE RELEASE" (WITH
EURO-OBD) or EC-510, "
FUEL PRESSURE RELEASE" (WITHOUT EURO-OBD).

Leave fuel pump fuse disconnecting to avoid fuel injection during measurement.
3. Remove ignition coil and spark plug from each cylinder. Refer to EM-29, "
IGNITION COIL" and EM-30,
"SPARK PLUG" .
4. Connect engine tachometer (not required in use of CONSULT-II).
5. Install compression tester with adapter onto spark plug hole.

Use compression gauge whose picking up end inserted to
spark plug hole is smaller than 20 mm (0.79 in) in diameter.
Otherwise, it may be caught by cylinder head during removal.
6. With accelerator pedal fully depressed, turn ignition switch to “START” for cranking. When the gauge
pointer stabilizes, read the compression pressure and engine rpm. Perform these steps to check each cyl-
inder.
Compression pressure:
Unit: kPa (bar, kg/cm2 , psi) /rpm
CAUTION:
Always use a fully changed battery to obtain specified engine speed.

If the engine speed is out of specified range, check battery liquid for proper gravity. Check engine
speed again with normal battery gravity.

If compression pressure is below minimum value, check valve clearances and parts associated with
combustion chamber (Valve, valve seat, piston, piston ring, cylinder bore, cylinder head, cylinder head
gasket). After the checking, measure the compression pressure again.

If some cylinders have low compression pressure, pour small amount of engine oil into the spark plug
hole of the cylinder to re-check it for compression.
–If the added engine oil improves the compression, piston rings may be worn out or damaged. Check
piston rings and replace if necessary.
KBIA0130E
SBIA0533E
Engine type Standard Minimum Differential limit between cylinders
QR20DE 1,190 (11.9, 12.1, 173) / 250 990 (9.9, 10.1, 144) / 250
100 (1.0, 1.0, 14) / 250
QR25DE 1,250 (12.5, 12.8, 181) / 250 1,060 (10.6, 10.8, 154) / 250

EM-68
[QR]
CYLINDER HEAD

–If the compression pressure remains at low level despite the addition of engine oil, valves may be mal-
functioning. Check valves for damage. Replace valve or valve seat accordingly.

If two adjacent cylinders have respectively low compression pressure and their compression remains
low even after the addition of engine oil, gaskets are leaking. In such a case, replace cylinder head gas-
kets.
7. After inspection is completed, install removed parts.
8. Start engine, and confirm that engine runs smoothly.
9. Perform trouble diagnosis. If DTC appears, erase it. Refer to EC-73, "
TROUBLE DIAGNOSIS" (WITH
EURO-OBD) or EC-520, "
TROUBLE DIAGNOSIS" (WITHOUT EURO-OBD).
Removal and InstallationEBS00KNQ
REMOVAL
1. Release fuel pressure. Refer to EC-48, "FUEL PRESSURE RELEASE" (WITH EURO-OBD) or EC-510,
"FUEL PRESSURE RELEASE" (WITHOUT EURO-OBD).
2. Drain engine coolant and engine oil. Refer to CO-9, "
Changing Engine Coolant" and LU-8, "Changing
Engine Oil" .
3. Remove the following components and related parts.

Exhaust manifold and three way catalyst assembly; Refer to EM-23, "EXHAUST MANIFOLD AND
THREE WAY CATALYST" .

Intake manifold and fuel tube assembly (QR20DE); Refer to EM-17, "Removal and Installation
(QR20DE)" .

Intake manifold collector, intake manifold and fuel tube assembly (QR25DE); Refer to EM-20, "Removal
and Installation (QR25DE)" .

Water control valve and housing (water outlet); Refer to CO-22, "THERMOSTAT AND WATER CON-
TROL VALVE" .
NOTE:
Can be removed and installed even when assembled with cylinder head.
4. Remove front cover and timing chain. Refer to EM-44, "
TIMING CHAIN" .
5. Remove camshafts. Refer to EM-53, "
CAMSHAFT" .
6. Securely support bottom of cylinder block with a jack or equivalent tool, and release the hoist that was
supporting it.
1. Cylinder head assembly 2. Cylinder head gasket 3. Cylinder head bolt
PBIC2185E

EM-74
[QR]
CYLINDER HEAD

Valve Guide Inner Diameter
Measure the inner diameter of valve guide with a bore gauge.
Valve Guide Clearance
(Valve guide clearance) = (Valve guide inner diameter) – (Valve stem diameter).

If it exceeds the limit, replace valve guide and/or valve.
VALVE GUIDE REPLACEMENT
When valve guide is removed, replace with oversized [0.2 mm (0.008 in)] valve guide.
1. To remove valve guide, heat cylinder head to 110 to 130°C (230
to 266°F) by soaking in heated oil.
2. Drive out valve guide with a press [under a 20 kN (2 ton, 2.2 US
ton, 2.0 lmp ton) pressure] or hammer and suitable tool.
CAUTION:
Cylinder head contains heat, when working, wear protective
equipment to avoid getting burned.
3. Ream cylinder head valve guide hole with a valve guide reamer
(commercial service tool).Standard
Intake and Exhaust
: 6.000 - 6.018 mm (0.2362 - 0.2369 in)
Valve guide clearance:
Standard
Intake : 0.020 - 0.053 mm (0.0008 - 0.0021 in)
Exhaust : 0.030 - 0.063 mm (0.0012 - 0.0025 in)
Limit
Intake : 0.08 mm (0.003 in)
Exhaust : 0.09 mm (0.004 in)
SEM008A
SEM931C
Valve guide hole diameter (for service parts):
Intake and exhaust
: 10.175 - 10.196 mm (0.4006 - 0.4014 in)
SEM932C