2003 NISSAN X-TRAIL code

AT-60
[EURO-OBD]
TROUBLE DIAGNOSIS — INTRODUCTION
4. 4-
3.Cruise testAT-74, "3.
CRUISE
TEST"
AT-78,
"Cruise Test
—Part 1"
Part-1
o8. Vehicle Cannot Be Started From D
1,AT- 2 4 2 , "8. Vehicle Cannot Be Started From D1".
o9. A/T Does Not Shift: D
1®D2Or Does Not Kickdown: D4®D2,AT-244, "9. A/T Does Not Shift: D1
®D2Or Does Not Kickdown: D4®D2".
o10. A/T Does Not Shift: D
2®D3,AT-246, "10. A/T Does Not Shift: D2®D3".
o11. A/T Does Not Shift: D
3®D4,AT-249, "11.A/TDoesNotShift:D3®D4".
o12. A/T Does Not Perform Lock-up,AT-252, "
12. A/T Does Not Perform Lock-up".
o13. A/T Does Not Hold Lock-up Condition,AT-253, "
13. A/T Does Not Hold Lock-up Condition".
o14. Lock-up Is Not Released,AT-254, "
14. Lock-up Is Not Released".
o15. Engine Speed Does Not Return To Idle (Light Braking D
4®D3),AT- 2 5 5 , "15. Engine Speed Does
Not Return To Idle (Light Braking D4®D3)".
Part-2AT-81,
"Cruise Test
—Part 2"o16. Vehicle Does Not Start From D1,AT-257, "16. Vehicle Does Not Start From D1".
o9. A/T Does Not Shift: D
1®D2Or Does Not Kickdown: D4®D2,AT-244, "9. A/T Does Not Shift: D1
®D2Or Does Not Kickdown: D4®D2".
o10. A/T Does Not Shift: D
2®D3,AT-246, "10. A/T Does Not Shift: D2®D3".
o11. A/T Does Not Shift: D
3®D4,AT-249, "11.A/TDoesNotShift:D3®D4".
Part-3AT-83,
"Cruise Test
—Part 3"o17. A/T Does Not Shift: D4®D3When Overdrive Control Switch “ON”®“OFF”,AT- 2 5 8 , "17. A/T Does
Not Shift: D4®D3, When Overdrive Control Switch“ON”®“OFF”".
o15. Engine Speed Does Not Return To Idle (Engine Brake In D
3),AT- 2 5 5 , "15. Engine Speed Does Not
Return To Idle (Light Braking D4®D3)".
o18. A/T Does Not Shift: D
3®22, When Selector Lever “D”®“2” Position,AT- 2 5 8 , "18. A/T Does Not
Shift: D3®22, When Selector Lever“D”®“2”Position".
o15. Engine Speed Does Not Return To Idle (Engine Brake In 2
2),AT-255, "15. Engine Speed Does Not
Return To Idle (Light Braking D4®D3)".
o19. A/T Does Not Shift: 2
2®11, When Selector Lever “2”®“1” Position,AT-259, "19. A/T Does Not
Shift: 22®11, When Selector Lever“2”®“1”Position".
o20. Vehicle Does Not Decelerate By Engine Brake,AT- 2 5 9 , "
20. Vehicle Does Not Decelerate By Engine
Brake".
o21. TCM Self-diagnosis Does Not Activate (PNP & Overdrive control switches, and throttle position sen-
sor circuit checks),AT-260, "
21. TCM Self-diagnosis Does Not Activate (PNP & Overdrive Control
Switches, and Throttle Position Sensor Circuit Checks)".
oSELF-DIAGNOSTIC PROCEDURE/DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCE-
DURE — Mark detected items.
oPNP switch,AT-130, "
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH".
oA/T fluid temperature sensor,AT- 1 3 6 , "
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIR-
CUIT".
oVehicle speed sensor·A/T (Revolution sensor),AT-142, "
DTC P0720 VEHICLE SPEED SEN-
SOR·A/T (REVOLUTION SENSOR)".
oEngine speed signal,AT-147, "
DTC P0725 ENGINE SPEED SIGNAL".
oTorque converter clutch solenoid valve,AT- 1 8 1 , "
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE".
oLine pressure solenoid valve,AT- 1 8 6 , "
DTC P0745 LINE PRESSURE SOLENOID VALVE".
oShift solenoid valve A,AT-193, "
DTC P0750 SHIFT SOLENOID VALVE A".
oShift solenoid valve B,AT-198, "
DTC P0755 SHIFT SOLENOID VALVE B".
oAccelerator pedal position (App) sensor,AT- 2 0 3 , "
DTC P1705 ACCELERATOR PEDAL POSITION
(APP) SENSOR".
oOverrun clutch solenoid valve,AT-208, "
DTCP1760OVERRUNCLUTCHSOLENOIDVALVE".
oPNP & overdrive control switches, and throttle position sentor,AT- 2 6 0 , "
21. TCM Self-diagnosis
Does Not Activate (PNP & Overdrive Control Switches, and Throttle Position Sensor Circuit Checks)"
.
oA/T fluid temperature sensor and TCM power source,AT- 2 1 6 , "
DTCBATT/FLUIDTEMPSEN(A/T
FLUID TEMP SENSOR CIRCUIT AND TCM POWER SOURCE)".
oVehicle speed sensor·MTR,AT- 2 2 2 , "
DTC VEHICLE SPEED SENSOR MTR".
oCAN communication line,EC-114, "
DTC U1000 CAN COMMUNICATION LINE".
oControl unit (RAM), control unit (ROM),AT- 2 2 6 , "
DTC CONTROL UNIT (RAM), CONTROL UNIT
(ROM)".
oControl unit (EEP ROM),AT-228, "
DTC CONTROL UNIT(EEPROM)".
oBattery
oOthers

TROUBLE DIAGNOSIS — INTRODUCTION
AT-63
[EURO-OBD]
D
E
F
G
H
I
J
K
L
MA
B
AT
*1:AT- 5 7 , "Information from Customer"*2:AT- 5 8 , "Diagnostic Worksheet"*3:AT-7 , "ServiceNoticeorPrecau-
tions"
*4:AT- 6 4 , "A/T Fluid Check"*5:AT- 6 5 , "Stall Test"andAT- 6 8 , "Line Pressure
Te s t"
*6:AT-6 9 , "Road Test"
*7:AT- 4 1 , "CONSULT-II"*8:AT- 3 7 , "ON BOARD DIAGNOSTIC SYSTEM
DESCRIPTION"
*9:AT-5 0 , "Diagnostic Procedure
Without CONSULT-II"
*10:AT- 1 3 0 , "DTC P0705 PARK/NEU-
TRAL POSITION (PNP) SWITCH"
*11:AT- 2 2 2 , "DTC VEHICLE SPEED SENSOR
MTR"andAT-226, "DTC CONTROL UNIT
(RAM), CONTROL UNIT (ROM)"toAT- 2 2 8 ,
"DTC CONTROL UNIT(EEPROM)"
*12:AT-2 3 2 , "1. O/D OFF Indicator
Lamp Does Not Come On"
*13:AT- 2 5 9 , "20. Vehicle Does Not Decel-
erate By Engine Brake"
*14:AT- 8 6 , "Symptom Chart"*15:AT-3 9 , "HOW TO ERASE DTC"
*16:AT- 1 3 1 , "DIAGNOSTIC TROUBLE
CODE (DTC) CONFIRMATION PRO-
CEDURE"
*17:AT- 2 2 2 , "DTC VEHICLE SPEED SENSOR
MTR"andAT-226, "DTC CONTROL UNIT
(RAM), CONTROL UNIT (ROM)"toAT- 2 2 8 ,
"DTC CONTROL UNIT(EEPROM)"
*18: EC-XX

AT-130
[EURO-OBD]
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
PFP:32006
DescriptionECS004QW
lThe PNP switch assembly includes a transmission range switch.
lThe transmission range switch detects the selector lever posi-
tion and sends a signal to the TCM.
TCM TERMINALS AND REFERENCE VALUE
Remarks: Specification data are reference values.
ON BOARD DIAGNOSIS LOGIC
SCIA0752E
Te r m i -
nal No.Wire color Item ConditionJudgement stan-
dard
(Approx.)
26 BR/YPNP switch “1”
position
andWhen setting selector lever to “1”
position.Battery voltage
When setting selector lever to other
positions.0V
27 LPNP switch “2”
positionWhen setting selector lever to “2”
position.Battery voltage
When setting selector lever to other
positions.0V
34 W/GPNP switch “D”
positionWhen setting selector lever to “D”
position.Battery voltage
When setting selector lever to other
positions.0V
35 L/WPNP switch “R”
positionWhen setting selector lever to “R”
position.Battery voltage
When setting selector lever to other
positions.0V
36 GPNP switch “N” or
“P” positionWhen setting selector lever to “N” or
“P” position.Battery voltage
When setting selector lever to other
positions.0V
Diagnostic trouble code Malfunction is detected when ... Check items (Possible cause)
:PNPSW/CIRC
TCM does not receive the correct voltage
signal from the switch based on the gear
position.
lHarness or connectors
(The PNP switch circuit is open or
shorted.)
lPNP switch : P0705

DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
AT-131
[EURO-OBD]
D
E
F
G
H
I
J
K
L
MA
B
AT
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCE-
DURE” has been previously conducted, always turn ignition
switch “OFF” and wait at least 5 seconds before conducting the
next test.
After the repair, perform the following procedure to confirm the mal-
function is eliminated.
With CONSULT-II
1. Turn ignition switch “ON”.
2. Select “DATA MONITOR” mode for “ENGINE” with CONSULT-II.
3. Start engine and maintain the following conditions for at least 5
consecutive seconds.
VHCL SPEED SE: 10 km/h (6 MPH) or more
THRTL POS SEN: More than 1.3V
Selector lever: D position (OD “ON” or “OFF”)
With GST
Follow the procedure “With CONSULT-II”.
SAT014K
SAT020K

AT-134
[EURO-OBD]
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH
2.CHECK PNP SWITCH CIRCUIT (WITHOUT CONSULT-II)
Without CONSULT-II
1. Turn ignition switch to “ON” position.
(Do not start engine.)
2. Check voltage between TCM terminals 26, 27, 34, 35, 36 and
ground while moving selector lever through each position.
OK or NG
OK >> GO TO 3
NG >> Check the following items:
lPNP switch
Refer to “Component Inspection”,AT - 1 3 5 , "
Component Inspection".
lHarness for short or open between ignition switch and PNP switch (Main harness)
lHarness for short or open between PNP switch and TCM (Main harness)
lIgnition switch and fuse
Refer toPG-2, "
POWER SUPPLY ROUTING", “POWER SUPPLY ROUTING”.
lDiode (P, N positions)
3.CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure,AT- 1 3 1 , "
DIAGNOSTIC TROUBLE CODE
(DTC) CONFIRMATION PROCEDURE".
OK or NG
OK >>INSPECTION END
NG >> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector. Vo l ta g e :
B : Battery voltage
0:0V
MTBL0136
SCIA0753E

AT-136
[EURO-OBD]
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
PFP:31940
DescriptionECS004R0
The A/T fluid temperature sensor detects the A/T fluid temperature
and sends a signal to the TCM.
CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE
Remarks: Specification data are reference values.
TCM TERMINALS AND REFERENCE VALUE
Remarks: Specification data are reference values.
ON BOARD DIAGNOSIS LOGIC
SCIA0718E
SAT021J
Monitor item Condition Specification (Approximately)
A/T fluid temperature sensorCold [20°C(68°F)]
¯
Hot [80°C(176°F)]1.5V
¯
0.5V2.5 kW
¯
0.3 kW
Te r m i -
nal No.Wire color Item ConditionJudgement stan-
dard
(Approx.)
42 BThrottle position
sensor
(Ground)———
47 BRA/T fluid tempera-
ture sensorWhen ATF temperature is 20°C
(68°F).1.5V
When ATF temperature is 80°C
(176°F).0.5V
Diagnostic trouble code Malfunction is detected when ... Check items (Possible cause)
: ATF TEMP SEN/CIRC
TCM receives an excessively low or high
voltage from the sensor.
lHarness or connectors
(The sensor circuit is open or shorted.)
lA/T fluid temperature sensor
: P0710

DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
AT-137
[EURO-OBD]
D
E
F
G
H
I
J
K
L
MA
B
AT
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DIAGNOSTIC TROUBLE CODE CONFIRMATION PROCE-
DURE” has been previously conducted, always turn ignition
switch “OFF” and wait at least 5 seconds before conducting the
next test.
After the repair, perform the following procedure to confirm the mal-
function is eliminated.
With CONSULT-II
1. Turn ignition switch “ON” and select “DATA MONITOR” mode for
“ENGINE” with CONSULT-II.
2. Start engine and maintain the following conditions for at least 10
minutes (Total). (It is not necessary to maintain continuously.)
CMPS·RPM (REF): 450 rpm or more
VHCL SPEED SE: 10 km/h (6 MPH) or more
THRTL POS SEN: More than 1.2V
Selector lever: D position (OD “ON”)
With GST
Follow the procedure “With CONSULT-II”.
SAT014K
SAT020K

AT-140
[EURO-OBD]
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT
3.CHECK INPUT SIGNAL OF A/T FLUID TEMPERATURE SENSOR (WITHOUT CONSULT-II)
Without CONSULT-II
1. Start engine.
2. Check voltage between TCM terminal 47 and ground while warming up A/T.
3. Turn ignition switch to “OFF” position.
4. Disconnect TCM harness connector.
5. Check continuity between terminal 42 and ground.
If OK, check harness for short to ground and short to power.
OK or NG
OK >> GOTO4
NG >> GOTO5
4.CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure,AT- 1 3 7 , "
DIAGNOSTIC TROUBLE CODE
(DTC) CONFIRMATION PROCEDURE".
OK or NG
OK >>INSPECTION END
NG >> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector. Vo l ta g e :
Cold [20°C(68°F)]®Hot [80°C (176°F)]
Approximately 1.5V®0.5V
SCIA0738E
Continuity should exist.
SCIA0739E