2003 NISSAN TEANA engine control

ATC-150
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
CompressorBJS000I4
LubricantBJS000I5
RefrigerantBJS000I6
Engine Idling SpeedBJS000I7
Refer to EC-45, "Idle Speed and Ignition Timing Check" (QR engine) or EC-387, "Idle Speed and Ignition Tim-
ing Check" (VQ engine).
Belt TensionBJS000I8
Refer to EM-14, "DRIVE BELTS" (QR engine) or EM-128, "DRIVE BELTS" (VQ engine).
ModelZEXEL VALEO CLIMATE CONTROL make
DKS-17D
Ty p eSwash plate
Displacement
cm
3 (cu in)/rev175 (10.7)
Cylinder bore × stroke
mm (in)30.5 (1.20) × 24.0 (0.94)
Direction of rotationClockwise (viewed from drive end)
Drive beltPoly V
ModelZEXEL VALEO CLIMATE CONTROL make
DKS-17D
NameNissan A/C System Oil Type S (DH-PS)
Capacity
m (lmp fl oz)Total in system 150 (5.3)
Compressor (Service part) charg-
ing amount150 (5.3)
Ty p eHFC-134a (R-134a)
Capacity
kg (lb)0.5 (1.1)

AUDIO (WITH INTEGRATED COLOR DISPLAY SYSTEM)
AV-33
C
D
E
F
G
H
I
J
L
MA
B
AV

Symptom ChartBKS0028V

The majority of the audio malfunctions are the result of outside causes (bad CD, electromagnetic interfer-
ence, etc.). Check the symptoms below to diagnose the malfunction.

The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunction-
ing. Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and
operation of each piece of electrical equipment, and then determine the cause.

CD-R is not guaranteed to play because they can contain compressed audio (MP3, WMA) or could be
incorrectly mastered by the customer on a computer.

Check if the CDs carry the Compact Disc Logo. If not, the disc is not mastered to the “red book” Compact
Disc Standard and may not play.

Make sure that other operation except audio system can be performed with A/C and AV switch. If these
operations are inoperative with A/C and AV switch, refer to AV- 9 7 , "
Unable to Operate System with A/C
and AV Switch" .
NOTE:
Noise resulting from variations in field strength, such as fading noise and multi-path noise, or external noise
from trains and other sources. It is not a malfunction.

Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.

Multi-path noise: This noise results from a time difference between the broadcast waves directly from the
station arriving at the antenna and the waves reflected by mountains or buildings.
Symptom Possible malfunction location
Audio system does not work properly.

Audio unit power supply circuit

Communication signal circuit between audio unit and display unit

A/C and AV switch

Audio unit
CD auto changer does not work properly.

CD auto changer power supply circuit

Communication signal circuit between audio unit and CD auto changer

CD auto changer

Audio unit
No sound can be heard from all speakers. Audio unit
No sound can be heard from one or several speakers.

Audio signal circuit between audio unit and speaker

Speaker

Tweeter

Audio unit
No sound can be heard from radio or noise is caught.

Antenna amp. ON signal circuit

Antenna feeder

Rear window antenna

Antenna amp.

Audio unit
Unable to operate audio system with rear audio control
switch.

Remote control signal circuit between rear audio control switch and A/C
and AV switch

Rear audio control switch

A/C and AV switch

INTEGRATED DISPLAY SYSTEM
AV-55
C
D
E
F
G
H
I
J
L
MA
B
AV

On Board Self-Diagnosis FunctionBKS00228
DESCRIPTION
When performing self-diagnosis mode, the following menu is displayed.
DIAGNOSIS ITEM
Self-Diagnosis ModeBKS00229
OPERATION PROCEDURES
1. Start the engine.
2. Turn the audio system OFF.
3. While pressing the “MUTE” button, turn the volume control dial
clockwise or counterclockwise for 30 clicks or more. (When the
self-diagnosis mode is started, a short beep will be heard.)
4. Initial diagnosis screen is displayed.

Perform diagnosis according to the audio preset No. “1, 2, 3,
4”.
FULL BLINK
All display unit segments turn ON.
Diagnosis itemFunction
switchDescription
FULL BLINK 1 All display unit segments turn ON.
HVAC DIAG 2 Self-diagnosis of air conditioner system is performed.
VERSION 3 Software version of each unit is displayed.
DIAG END 4 Exit from self-diagnosis mode and return to normal screen.
SKIB0828E
SKIA7023J
SKIA7024J

AV-86
INTEGRATED COLOR DISPLAY SYSTEM

OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system OFF.
3. While pressing the “MUTE” button, turn the volume control dial
clockwise or counterclockwise for 30 clicks or more. (When the
self-diagnosis mode is started, a short beep will be heard.)
4. The initial diagnosis screen is displayed.
5. The item of “DCU Failure Diagnosis” and “DCU Confirmation”
can be selected.

Select each item with “FM” button and “AM” button of A/C and
AV switch, and then determine by “CD·CHG” button.

When pressing “3 RANDOM” button of A/C and AV switch,
return to the previous screen.
SKIB8825E
SKIB0829E
SKIB1985E

BL-4
INDEX FOR DTC

INDEX FOR DTCPFP:00024
DTC No. Index BIS001TQ
NOTE:
When CAN COMM CIRCUIT [U1000] or CONTROL UNIT (CAN) [U1010] displayed, give priority to performing
trouble diagnosis.
INTELLIGENT KEY / NATS I-KEY
*: It is possible to display it only with the program card only for the engine immobilizer system.
NATS V5.0
The program card only for the engine immobilizer system is necessary for the following display item.
DTCSelf-diagnosis item
(CONSULT-II indication)DTC detection condition
NO DTC NO DTC —
U1000 CAN COMM CIRCUITWhen Intelligent Key unit is not transmitting or receiving CAN communication signal for
2 seconds or more.
U1010 CONTROL UNIT (CAN) When detecting error during the initial diagnosis of CAN controller of Intelligent Key unit.
B2013* STRG COMM CIRCUIT Communication malfunction with steering lock unit is detected.
B2552* INTELLGENT KEY Internal malfunction is detected in Intelligent Key unit.
B2590* DISCORD BCM-I-KEY The ID verification results between Intelligent Key unit and BCM are NG.
DTCSelf-diagnosis item
(CONSULT-II indication)DTC detection condition
NO DTC NO DTC —
—DON’T ERASE BEFORE
CHECKING END DIAGThere is the engine trouble diagnosis information in ECM. (ECM trouble diagnosis is nec-
essary separately)
P1610 LOCK MODEThe immobilizer switches to the mode that prevents the engine from being started. If the
ID verification between BCM and ECM is NG, the ID verification malfunction between
remote control starter and BCM may be detected 5 time or more.
P1611 ID DISCORD, IMM-ECM The ID verification results between BCM and ECM are NG. The registration is necessary.
P1612 CHAIN OF ECM-IMMU Communication impossible between ECM and NATS IMMU.
P1614 CHAIN OF IMMU-KEY NATS IMMU cannot receive the key ID signal.
P1615 DIFFERENCE OF KEYNATS IMMU can receive the key ID signal but the result of ID verification between key ID
and NATS IMMU is NG.

BL-16
HOOD

Removal and Installation of Hood Lock ControlBIS000VR
REMOVAL
Hood Lock and Hood Lock Cable
1. Remove hood lock bolts.
2. Disconnect hood lock cable from hood lock.
3. Remove fender protector (LH). Refer to EI-23, "
FENDER PRO-
TECTOR" .
4. Remove hood lock cable clips, from radiator core upper support
and hood ledge.
5. Remove hood opener and grommet on lower dashboard.
6. Pull out hood lock cable toward passenger room.
CAUTION:
While pulling the cable, be careful not to damage (peel) outer surface of the cable on edges of
body through hole.
INSTALLATION
Install in the reverse order of removal.
1. Pull the hood lock cable through the panel hole to the engine
compartment.
CAUTION:
Be careful not to bend the cable too much, keeping the
radius 100 mm (3.94 in) or more.
2. Make sure that the cable is not offset from the positioning grommet, and push the grommet into the panel
hole securely.
3. Apply sealant (POS seal) to area on the grommet indicated with the * mark.
1. Hood lock cable 2. Hood lock
PIIB1753E
: 23.6N·m (2.4 kg-m, 18 ft-lb)
PIIB1754E
PIIA0173E

BL-70
INTELLIGENT KEY SYSTEM

System DescriptionBIS000WZ

The Intelligent Key system is a system that makes it possible to lock and unlock the door locks (door lock
function) and start the engine (engine start function) by carrying around the Intelligent Key, which operates
based on the results of electrical key-ID verification using two-way communications between the Intelli-
gent Key and the vehicle

Operation of the remote control buttons on the Intelligent Key also provides the same functions as the
remote keyless entry system. (Remote keyless entry functions)

As an ignition key warning function, when a door lock is locked or unlocked with request switch or remote
controller button operation, the hazard lamps flash and the Intelligent Key warning buzzer sounds.

Even if the Intelligent Key battery runs down, the door locks can be locked and unlocked and the engine
started with the mechanical key built into the Intelligent Key.

If an Intelligent Key is lost, a new Intelligent Key can be registered. A maximum of 4 Intelligent Keys can
be registered.

It has been made possible to diagnose the system, change the function setting and register an Intelligent
Key with the CONSULT-II.
DOOR LOCK/UNLOCK, TRUNK OPEN FUNCTION
Operation Description

When the driver door, passenger door, or trunk open request switch is pressed, Intelligent Key unit sends
a request signal from the outside key antenna corresponding to the pressed request switch, key-ID verifi-
cation is performed using two-way communication with Intelligent Key, and if ID is successfully verified, a
door lock/unlock request signal is sent to BCM using CAN communication to lock/unlock the door lock.

When door is locking, door is unlocked, when door is unlocking, door is locked.

When door lock is locked/unlocked by door request switch operation, hazard lamps flash and Intelligent
Key warning buzzer sounds.

With the locking operation of door request switch, door lock actuators of all door are locked.

When trunk open request switch is pushed, trunk lid is opened.
Operation Condition
Auto Door Lock Function
After the door request switch in the driver or passenger door is operated and the vehicle door locks are
unlocked, all the doors are automatically locked unless the mechanical key is inserted into the ignition knob,
the ignition knob is pressed, any door request switch is pressed, any one of the doors is opened, or an Intelli-
gent Key remote control button is operated within 2 minutes.
Hazard Reminder Function
The hazard lamps are flashed when the door lock is locked or unlocked by door request switch operation.
When ignition switch ON or any door is opened, key reminder function is not operate.
Request switch operation Operating conditions
Request switch (Driver side) When all the conditions below are met

All doors are closed (for lock operation)

Remove mechanical key from ignition key cylinder (key switch: OFF)

Ignition knob is not press (ignition knob switch: OFF)

The Intelligent Key is in the outside key antenna detection area for the door for which
the door request switch was operated. Request switch (passenger side)
Request switch (trunk lid)When all the conditions below are met

The Intelligent Key is in the antenna detection area for the outside key antenna (rear
bumper).

When the Intelligent Key is detection for the Inside Key antenna, but another Intelli-
gent Key is detected for the outside key antenna.
Vehicle operation Hazard lamp
Door unlock operation Twice
Door lock operationOnce

BL-72
INTELLIGENT KEY SYSTEM

Hazard Reminder Function
The hazard lamps are flashed when the door lock is locked or unlocked by remote controller button.
When ignition switch ON or any door is opened, key reminder function is not operate.
List of Operation Related Parts
Parts marked with × are the parts related to operation.
ENGINE START FUNCTION
Operation Description

When ignition knob is pressed, Intelligent Key unit sends request signal from inside key antenna, key-ID
verification is performed with Intelligent Key using two-way communication, and if verification is success-
ful, an ignition rotation prohibition latch release signal is sent to steering lock unit. Steering lock unit
releases ignition knob rotation prohibition latch. (Ignition knob can now be turned.)

When it becomes possible to rotate the ignition knob, “KEY” warning lamp in combination meter lights up
green to notify driver that ignition knob can be turned.
NOTE:
When it becomes impossible to rotate the ignition knob, “KEY” warning lamp in combination meter lights
up red.

When key-ID verification is successful, Intelligent Key unit uses CAN communication to send engine start
permission signal to BCM.

When BCM receives engine start permission signal, it uses CAN communication to sent starter request
signal to IPDM E/R so that the engine will start when ignition knob is rotated to START position.
Operation Range
Engine can be started when Intelligent Key is in the vehicle. However, sometimes engine might not start when
Intelligent Key is on instrument panel, rear parcel shelf, trunk room or in glove box.
Unlock
Remove mechanical key from ignition key cylinder (key switch: OFF)

Ignition knob is not press (ignition knob switch: OFF)
Trunk open

Remove mechanical key from ignition key cylinder (key switch: OFF)

Ignition knob is not press (ignition knob switch: OFF)

When trunk button pressed more than 0.5 seconds Remote controller button operation Operating condition
Vehicle operation Hazard lamp
Door unlocking operation Twice
Door locking operation Once
Remote keyless entry functions
Intelligent Key
Key switch
Ignition knob switch
Door unlock sensor
Door switch
Trunk room lamp switch
Door lock actuator
Trunk lid opener actuator
Intelligent Key unit
CAN communication system
BCM
Combination meter
Hazard warning lamp
Door lock function by the remote control button××××× × ×××
Trunk open function by the remote control button××× × ××××
Hazard reminder function (Door lock)×××××