2003 NISSAN TEANA warning

TROUBLE DIAGNOSIS FOR SYMPTOMS
BRC-31
[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

2. CHECK FUNCTION
Disconnect ABS actuator and electric unit (control unit) connector to deactivate ABS. Check if braking force is
normal in this condition. Connect connector after inspection.
OK or NG
OK >> GO TO 3. Check Wheel Sensor and Sensor Rotor. Refer to BRC-30, "Excessive ABS Function
Operation Frequency" .
NG >> Check brake system.
Longer Stopping DistanceBFS000DE
CAUTION:
The stopping distance on slippery road surfaces might be longer with the ABS operating than when
the ABS is not operating.
1. CHECK FUNCTION
Turn ignition switch OFF. Disconnect ABS actuator and electric unit (control unit) connectors to deactivate
ABS. In this condition, check stopping distance. After inspection, connect connectors.
OK or NG
OK >> GO TO 3. Check Wheel Sensor and Sensor Rotor. Refer to BRC-30, "Excessive ABS Function
Operation Frequency" .
NG >>

Bleed air from the brake piping. Refer to BR-10, "Bleeding Brake System" .

Check brake system.
ABS Function Does Not OperateBFS000DF
CAUTION:
ABS does not operate when speed is 10 km/h (6 MPH) or lower.
1. CHECK ABS WARNING LAMP DISPLAY
Make sure that the warning lamp turns off approximately 1 second after the ignition switch is turned ON or
when driving.
OK or NG
OK >> GO TO 3. Check Wheel Sensor and Sensor Rotor. Refer to BRC-30, "Excessive ABS Function
Operation Frequency" .
NG >> Perform self-diagnosis. Refer to BRC-17, "
Self-Diagnosis" .
Pedal Vibration and ABS Operation Sound OccursBFS000DG
CAUTION:
Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly
depressed (just place a foot on it). However, this is normal.

When shifting gears

When driving on slippery road

During cornering at high speed

When passing over bumps or grooves [at approximately 50 mm (1.97 in) or more]

When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or more]
1. SYMPTOM CHECK 1
Check if there is pedal vibration and operation sound when the engine is started.
OK or NG
OK >> GO TO 2.
NG >> Perform self-diagnosis. Refer to BRC-17, "
Self-Diagnosis" .

BRC-36
[ABS]
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY)

REMOVAL
1. Disconnect ABS actuator and electric unit (control unit) connector.
2. Loosen brake tube flare nuts, then remove brake tubes from ABS actuator and electric unit (control unit).
3. Remove ABS actuator and electric unit (control unit) mounting bolts.
4. Remove ABS actuator and electric unit (control unit) from vehicle.
CAUTION:
Be careful of the following when removing ABS actuator and electric unit (control unit).

If the part number on the part number label (pasted on actuator upper surface) is the same, ABS
actuator and electric unit (control unit) cannot be used on another vehicle.
If it is used on another vehicle, ABS warning lamp, may turn ON or ABS may not operate normally.
When replacing ABS actuator and electric unit (control unit), must use new service parts.

Before servicing, disconnect both battery cables.

To remove brake tube, use a flare nut torque wrench to prevent flare nuts and brake tube from
being damaged. To install, use a flare nut torque wrench (commercial service tool) and tighten
with the specified torque.

Do not apply excessive impact to actuator, such as dropping it.

Do not remove and install ABS actuator and electric unit (control unit) by holding harness.
INSTALLATION
Install is in the reverse order of the removal.
CAUTION:
Be careful of the following when installing ABS actuator and electric unit (control unit).

Tighten the mounting bolts and nuts with the specified torque.

After the work, bleed air from brake piping. Refer to BR-10, "Bleeding Brake System" .

After installing body harness connector in the actuator, make sure connector is securely locked.

PRECAUTIONS
BRC-37
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

[VDC/TCS/ABS]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BFS000G3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Brake SystemBFS000DL

Recommended fluid is brake fluid “DOT 3” or “DOT 4”. Refer to MA-14, "RECOMMENDED FLUIDS AND
LUBRICANTS" .

Never reuse drained brake fluid.

Be careful not to splash brake fluid on painted areas.

To clean or wash all parts of master cylinder and disc brake caliper, use clean brake fluid.

Never use mineral oils such as gasoline or kerosene. They will
ruin rubber parts of the hydraulic system.

Using a flare nut wrench when removing flare nuts, and use a
flare nut torque wrench when tighten brake tube flare nuts.

When installing brake tubes, be sure to check torque.

Before working, turn ignition switch OFF and disconnect electri-
cal connector of ABS actuator and electric unit (control unit) or
battery negative terminal.
WARNING:
Clean brake pads and shoes with a waste cloth, then wipe with
a dust collector.
Precautions for Brake ControlBFS000DM

During ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating noise may
be heard from engine room. This is a normal status of operation check.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.

When an error is indicated by ABS or another warning lamp, collect all necessary information from cus-
tomer (what symptoms are present under what conditions) and check for simple causes before starting
diagnostic servicing. Besides electrical system inspection, check brake booster operation, brake fluid
level, and fluid leaks.

If tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.

If there is a radio, antenna, or antenna lead-in wire (including wiring) near control module, ABS function
may have a malfunction or error.

If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits, and improper wiring.

If the following components are replaced with non-genuine components or converted, the VDC OFF indi-
cator lamp and SLIP indicator lamp may turn on or the VDC system may not operate properly. Compo-
nents related to suspension (Shock Absorber, Strut, Spring, Bush, etc.), Tires, wheels (exclude specified
SBR820BA

SYSTEM DESCRIPTION
BRC-41
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

SYSTEM DESCRIPTIONPFP:00000
System DiagramBFS000DP
FunctionsBFS000DQ
VDC

In addition to the TCS/ABS function, the steering amount and brake operation amount are detected from
the steering angle sensor and brake switch, and the driving condition (amount of under-steering/over-
steering) is determined from information from the yaw rate/side/decel G sensor, vehicle speed sensor, etc.
This information is used to improve vehicle stability by controlling the braking and engine power to all four
wheels.

The SLIP indicator lamp flashes to inform the driver of VDC operation.

During VDC operation, the body and brake pedal lightly vibrate and mechanical noises may be heard.
This is normal.

ABS warning lamp, VDC OFF indicator lamp, and SLIP indicator lamp might turn on when the vehicle is
subject to strong shaking or large vibration, such as when the vehicle is on a turn table or a ship while
engine is running. In this case, restart engine on a normal road, and if ABS warning lamp, VDC OFF indi-
cator lamp, and SLIP indicator lamp turn off, there is no malfunction.
TCS

Speed signals for 4 wheels control engine output and transaxle conditions so that slip rate of the drive
wheels is optimum. ABS actuator and electric unit (control unit) detects wheelspin. Output from the control
unit controls brake fluid pressure to both LH and RH drive wheels while cutting fuel to the engine and clos-
ing the throttle valve to reduce engine torque when wheelspin is detected. Throttle position is continuously
controlled to ensure the appropriate engine torque at all times.

Depending on road conditions, the driver may have a sluggish feel. This is normal, because the optimum
traction has the highest priority by TCS operation.

TCS may be activated momentarily the vehicle suddenly accelerates, suddenly downshifts, or is driven on
a road with a varying surface friction coefficient.

During TCS operation, it informs a driver of system operation by flashing SLIP indicator lamp.
SFIA3329E

BRC-42
[VDC/TCS/ABS]
SYSTEM DESCRIPTION

ABS

The Anti-Lock Brake System is a function that detects wheel revolution while braking, and it improves
handling stability during sudden braking by electrically preventing 4 wheel lock. Maneuverability is also
improved for avoiding obstacles.

If the electrical system breaks down, then the fail-safe function is activated, ABS becomes inoperative,
and ABS warning lamp turns on.

Electrical system diagnosis by CONSULT-II is available.

During ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating noise may
be heard from engine room. This is a normal status of operation check.

Stopping distance may be longer than that of vehicles without ABS when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.
EBD

Electronic Brake Distribution is a function that detects subtle slippages between front and rear wheels dur-
ing braking, and it improves handling stability by electronically controlling Brake Fluid Pressure which
results in reduced rear wheel slippage.

In case of electrical system break down, the fail-safe function is activated, EBD and ABS becomes inoper-
ative, and ABS warning lamp and brake warning lamp are turned on.

Electrical system diagnosis by CONSULT-II is available.

During EBD operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.

Just after starting vehicle after ignition switch ON, brake pedal may vibrate or motor operating sound may
be heard from engine compartment. This is a normal condition of operation check.

Stopping distance may be longer than that of vehicles without EBD when vehicle drives on rough, gravel,
or snow-covered (fresh, deep snow) roads.
Fail-Safe FunctionBFS000DU
VDC/TCS SYSTEM
In the event an electrical malfunction occurs in the system, the VDC OFF indicator lamp and SLIP indicator
lamp in the combination meter will light up. At the same time, the VDC/TCS control is not performed, and the
vehicle is in the same conditions as a vehicle not equipped with the VDC/TCS function. However, the ABS
control operates normally.
If a malfunction is detected in the throttle control system, the VDC/TCS control is not performed and only the
ABS control operates normally.
CAUTION:
If fail-safe mode is initiated, perform self-diagnosis for the VDC/TCS/ABS control system.
ABS, EBD SYSTEM
In the event there is a malfunction with the electrical system, the ABS warning lamp, VDC OFF indicator lamp,
and SLIP indicator lamp will turn on when it is the ABS that is malfunctioning, and the brake warning lamp,
ABS warning lamp, VDC OFF indicator lamp, and SLIP indicator lamp will turn on when it is the EBD that is
malfunctioning. At the same time, the VDC/TCS/ABS will become one of the following conditions by the fail-
safe function.

When the ABS malfunctions, only the EBD operates. The condition is the same as that of models with
VDC/TCS/ABS.
NOTE:
ABS self-diagnosis sound may be heard. That is a normal condition because a self-diagnosis for “Ignition
switch ON” and “The first starting” are being performed.

When the EBD malfunctions, the EBD and ABS will not operate. The condition is the same as that of mod-
els without VDC/TCS/ABS and EBD.

TROUBLE DIAGNOSIS
BRC-55
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

Control Unit Input/Output Signal SpecificationsBFS000E1
REFERENCE VALUE FROM CONSULT-II
CAUTION:
The monitor displays the control unit calculation data. The normal values will be displayed even in the
event that the output circuit (harness) is open or shorted.
Monitor item Display itemDATA MONITOR
ConditionReference values for
normal operation
WHEEL SENSORVehicle speed calculated using sig-
nals from all four wheel sensorsVehicle stopped 0 [km/h (MPH)]
Vehicle running (Note 1)Almost in accordance
with speedometer dis-
play (within ± 10 %)
DECEL G SENSOR Decel G detected by decel G sensorWhen stopped -0.11 to +0.11 G
During acceleration Negative value
During deceleration Positive value
IN ABS S/V
OUT ABS S/VOperation condition of all solenoid
valvesWhen the actuator solenoid operates ON
When the actuator relay operates and
the actuator solenoid does not operateOFF
EBD WARN LAMP
(Note 2)Brake warning lamp ON/OFF condi-
tionWhen brake warning lamp is ON ON
When brake warning lamp is OFF OFF
STOP LAMP SW Brake pedal operation conditionBrake pedal depressed ON
Brake pedal not depressed OFF
MOTOR RELAYMotor and motor relay operation con-
ditionWhen motor relay and motor are
operatingON
When motor relay and motor are not
operatingOFF
ACTUATOR RLY Actuator relay operation conditionActuator relay activated ON
Actuator relay not activated OFF
ABS WARN LAMPABS warning lamp ON/OFF condition
(Note 3)When ABS warning lamp is ON ON
When ABS warning lamp is OFF OFF
OFF LAMPVDC OFF indicator lamp ON/OFF
condition (Note 4)When VDC OFF indicator lamp is ON ON
When VDC OFF indicator lamp is OFF OFF
OFF SW VDC OFF switch ON/OFF conditionWhen VDC OFF switch ON
(When the VDC OFF indicator lamp is
ON)ON
When VDC OFF switch OFF
(When the VDC OFF indicator lamp is
OFF)OFF
SLIP LAMPSLIP indicator lamp ON/OFF condi-
tion (Note 5)When SLIP indicator lamp is ON ON
When SLIP indicator lamp is OFF OFF
BATTERY VOLTBattery voltage supplied to ABS actu-
ator and electric unit (control unit)Ignition switch ON 10 - 16 V
GEARDetermined gearshift position from
the A/T switch signalAlways1: 1st gear
2: 2nd gear
3: 3rd gear
4: 4th gear
ENGINE SPEED Engine runningWith engine stopped 0 rpm
Engine runningAlmost in accordance
with tachometer display
YAW RATE SEN Yaw rate detected by yaw rate sensor When stopped−7.0 to +7.0 d/s

BRC-56
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS

Note 1: Confirm tire pressure is the standard value.
Note 2: Warning lamp can be used as both EBD warning lamp and brake warning.N POSI SIGShift position determined by the A/T
switch signalWhen in N position ON
Other than N position OFF
P POSI SIGShift position determined by the A/T
switch signalWhen in P position ON
Other than P position OFF
FR LH IN SOL
FR LH OUT SOL
FR RH IN SOL
FR RH OUT SOL
RR LH IN SOL
RR LH OUT SOL
RR RH IN SOL
RR RH OUT SOLOperation condition of all solenoid
valvesActuator (solenoid) is active (“ACTIVE
TEST” with CONSULT-II) and actuator
relay is active (ignition switch ON)ON
When actuator (solenoid) is not active
or actuator relay is not active (in fail-
safe mode)OFF
STOP LAMP SW2 Brake pedal operation conditionBrake pedal depressed ON
Brake pedal not depressed OFF
ACCEL POS SIGAccelerator open/close condition
(linked to the accelerator pedal)Do not step on the accelerator pedal
(When ignition switch is on)0 %
Step on the accelerator pedal
(When ignition switch is on)0 - 100 %
SIDE G SENSOR Side G detected by side G sensorWhen stopped
−1.1 to +1.1 m/s
2
Right turn Negative value
Left turn Positive value
STR ANGLE SIGSteering angle detected by steering
angle sensorStraight-ahead position -3.5° to 3.5°
Steering wheel turned right 0° to 756°
Steering wheel turned left 0° to -756°
EBD SIGNAL EBD operation conditionEBD activated ON
EBD not activated OFF
ABS SIGNAL ABS operation conditionABS activated ON
ABS not activated OFF
TCS SIGNAL TCS operation conditionTCS activated ON
TCS not activated OFF
VDC SIGNAL VDC operation conditionVDC activated ON
VDC not activated OFF
EBD FAIL SIG EBD fail-safe signal conditionIn EBD fail-safe ON
EBD is normal OFF
ABS FAIL SIG ABS fail-safe signal conditionIn ABS fail-safe ON
ABS is normal OFF
TCS FAIL SIG TCS fail-safe signal conditionIn TCS fail-safe ON
TCS is normal OFF
VDC FAIL SIG VDC fail-safe signal conditionIn VDC fail-safe ON
VDC is normal OFF
CRANKING SIG Cranking conditionAt cranking ON
Other than at cranking OFF
FLUID LEV SWBrake fluid level switch ON/OFF con-
ditionWhen brake fluid level switch is ON ON
When brake fluid level switch is OFF OFF Monitor item Display itemDATA MONITOR
ConditionReference values for
normal operation

TROUBLE DIAGNOSIS
BRC-57
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

Note 3: ON/OFF timing of ABS warning lamp
ON: For a while after ignition switch is turned ON, or when a malfunction is detected.
OFF: In a while after ignition switch is turned ON (when the system is in normal operation).
Note 4: ON/OFF timing of VDC OFF indicator lamp
ON: For a while after ignition switch is turned ON, or when a malfunction is detected, or VDC OFF switch is ON.
OFF: In a while after ignition switch is turned ON (when the system is in normal operation) and VDC OFF switch is OFF.
Note 5: ON/OFF timing of SLIP indicator lamp
ON: For a while after ignition switch is turned ON, or when a malfunction is detected.
OFF: In a while after ignition switch is turned ON (when the system is in normal operation).
Blink: When the VDC/TCS function is operating during driving.
CONSULT-II FunctionsBFS000E2
CONSULT-II MAIN FUNCTION
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II SETTING PROCEDURE
Refer to GI-34, "CONSULT-II Start Procedure" .
Diagnostic test mode Function Reference
WORK SUPPORTThis mode enables a technician to adjust some devices faster and more accu-
rately by following the indications on CONSULT-II.BRC-40, "
Adjustment of
Steering Angle Sensor
Neutral Position"
SELF-DIAG RESULTS Self-diagnostic results can be read and erased quickly.BRC-58, "Self-Diagno-
sis"
DATA MONITOR Input/Output data in the ABS actuator and electric unit (control unit) can be read.BRC-61, "Data Monitor"
CAN DIAG SUPPORT
MNTRThe results of transmit / receive diagnostic of CAN communication can be read.LAN-44, "CAN Diagnos-
tic Support Monitor"
ACTIVE TESTDiagnostic Test Mode in CONSULT-II drives some actuators apart from the ABS
actuator and electric unit (control unit) and also shifts some parameters in a
specified range.BRC-63, "Active Test"
FUNCTION TESTPerformed by CONSULT-II instead of a technician to determine whether each
system is “OK” or “NG”.—
ECU PART NUMBER ABS actuator and electric unit (control unit) part number can be read. —