2003 NISSAN TEANA Power

EM-42
[QR]
CAMSHAFT

4. Remove reservoir tank of power steering oil pump from bracket, and move power steering piping aside.
Refer to PS-39, "
HYDRAULIC LINE" .
CAUTION:
To avoid power steering fluid leakage, temporarily fix reservoir tank of power steering oil pump
vertically.
5. Remove intake valve timing control cover with the following procedure:
a. Disconnect intake valve timing control solenoid valve harness connector.
b. Disconnect ground cables and remove harness clip.
c. Remove intake valve timing control solenoid valve, if necessary.
d. Loosen bolts in reverse order as shown in the figure.
e . U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] o r e q u i v a l e n t t o o l t o c u t l i q -
uid gasket for removal.
CAUTION:
Be careful not to damage the mating surfaces.
6. Pull chain guide between camshaft sprockets out through front cover.
7. Set No. 1 cylinder at TDC on its compression stroke with the following procedure:
a. Remove splash guard (RH).
b. Rotate crankshaft pulley clockwise and align TDC mark to timing
indicator on front cover.
c. At the same time, make sure that the mating marks on camshaft
sprockets are located as shown in the figure.

If not, rotate crankshaft pulley one more turn to align mating
marks to the positions in the figure.
8. Remove camshaft sprockets with the following procedure:
a. Put indelible paint marks on timing chain link plate aligning with the mating marks on camshaft sprockets.
KBIA0085E
KBIA0190E
PBIC2351E

EM-54
[QR]
TIMING CHAIN

REMOVAL
1. Remove the following parts.

RH front road wheel and tire

Undercover and splash guard (RH)

PCV hose; Refer to EM-19, "INTAKE MANIFOLD" .

Ignition coil; Refer to EM-31, "IGNITION COIL" .

Rocker cover; Refer to EM-39, "ROCKER COVER" .

Reservoir tank of radiator; Refer to CO-13, "RADIATOR" .

Drive belt; Refer to EM-14, "DRIVE BELTS" .

Alternator; Refer to SC-27, "CHARGING SYSTEM" .

Drive belt auto-tensioner; Refer to EM-15, "Removal and Installation of Drive Belt Auto-Tensioner" .

Exhaust front tube; Refer to EX-2, "EXHAUST SYSTEM" .
2. Drain engine oil. Refer to LU-9, "
Changing Engine Oil" .
CAUTION:
Perform this step when engine is cold.
3. Remove A/C compressor with piping connected. Temporarily secure A/C compressor to vehicle side with
a rope to avoid putting a load on them. Refer to ATC-134, "
Removal and Installation of Compressor" .
4. Remove power steering oil pump with piping connected, and secure it to vehicle side temporarily. Refer to
PS-39, "
HYDRAULIC LINE" .
5. Securely support bottom of transaxle with suitable transmission jack.
6. Remove RH engine mounting insulator. Refer to EM-77, "
ENGINE ASSEMBLY" .
7. Remove oil pans (upper and lower), and oil strainer. Refer to EM-26, "
OIL PAN AND OIL STRAINER" .
8. To support engine, temporarily tighten removed front and rear engine mounting through-bolts for removing
oil pans (upper and lower). Refer to EM-77, "
ENGINE ASSEMBLY" .
9. Remove intake valve timing control cover with the following procedure:
a. Disconnect intake valve timing control solenoid valve harness connector.
b. Disconnect ground cables and remove harness clip.
c. Remove intake valve timing control solenoid valve, if necessary.
d. Loosen bolts in reverse order as shown in the figure.
e . U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] o r e q u i v a l e n t t o o l t o c u t l i q -
uid gasket for removal.
CAUTION:
Be careful not to damage the mating surfaces.
10. Pull chain guide between camshaft sprockets out through front cover.
11. Set No. 1 cylinder at TDC on its compression stroke with the following procedure:
a. Rotate crankshaft pulley clockwise and align TDC mark to timing
indicator on front cover.
KBIA0085E
KBIA0190E

EM-56
[QR]
TIMING CHAIN

a. Loosen mounting bolts in reverse order as shown in the figure,
and remove RH engine mounting bracket.
b . U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] o r e q u i v a l e n t t o o l t o c u t l i q -
uid gasket for removing front cover.
CAUTION:
Be careful not to damage the mating surfaces.
c. Pull out downward front cover.
CAUTION:
Do not let A/C and power steering pipings interfere with
upper part of front cover.
14. Remove front oil seal from front cover using suitable tool.
CAUTION:
Be careful not to damage front cover.
15. Remove timing chain with the following procedure:
a. Push in chain tensioner plunger. Insert a stopper pin into hole on
chain tensioner body to secure chain tensioner plunger and
remove chain tensioner.
NOTE:
Use approximately 0.5 mm (0.02 in) dia. hard metal pin as a
stopper pin.
b. Remove timing chain.
CAUTION:
Do not rotate crankshaft or camshaft while timing chain is removed. It causes interference
between valve and piston.
16. Remove camshaft sprockets. Refer to EM-41, "
CAMSHAFT" .
17. Remove timing chain slack guide, timing chain tension guide and oil pump drive spacer.
18. Remove balancer unit timing chain tensioner with the following procedure:
a. Lift lever up, and release ratchet claw for return proof.
b. Push tensioner sleeve in, and hold it.
c. Matching the hole on lever with the one on body, insert a stopper
pin to secure tensioner sleeve.
NOTE:
Use approximately 1 mm (0.04 in) dia. hard metal pin as a stop-
per pin.
d. Remove balancer unit timing chain tensioner.
KBIA0083E
KBIA0048E
KBIA0121E

EM-60
[QR]
TIMING CHAIN

b. Apply a continuous bead of liquid gasket with tube presser [SST:
WS39930000] to front cover as shown in the figure.
Use Genuine Liquid Gasket or equivalent.
NOTE:
Application instruction differs depending on the position.
c. Make sure that mating marks of timing chain and each sprocket are still aligned. Then install front cover.

When installing, align flat faces at oil pump drive spacer and oil pump inner rotor.
CAUTION:

Do not let A/C and power steering pipings interfere with upper part of front cover.

Be careful not to damage front oil seal by interference with front end of crankshaft.
d. Tighten mounting bolts in numerical order as shown in the fig-
ure.

Refer to the following for locating M6 bolts.

At the same time, install RH engine mounting bracket. (Bolt
positions 1 to 4 in the figure)
e. After all bolts are tightened, retighten them to specified torque in
numerical order as shown in the figure.
CAUTION:
Be sure to wipe off any excessive liquid gasket leaking to
surface for fitting oil pan (upper).
8. Install chain guide between camshaft sprockets.
9. Install intake valve timing control cover with the following procedure:
a. Install oil rings to the camshaft sprocket (INT) insertion points on backside of intake valve timing control
cover.
b. Install O-ring to front cover.Detail of A : Cross over the start of the applica-
tion and the end.
Detail of B : Apply liquid gasket outside of bolt
holes. (For all bolt holes other than
B, apply to the inside.)
Detail of C : Between here only, apply 4.5 - 5.5
mm (0.177 - 0.217 in) dia.
SBIA0267E
Bolt length: Bolt position
45 mm (1.77 in) : 5, 14, 17
20 mm (0.79 in) : Except the above (Except 1 to 4)
KBIA0083E

CYLINDER HEAD
EM-69
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

Summary of the inspection items:
* Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.Item Before starting engine Engine running After engine stopped
Engine coolant Level Leakage Level
Engine oil Level Leakage Level
Other oils and fluid* Level Leakage Level
Fuel Leakage Leakage Leakage
Exhaust gases — Leakage —

EM-78
[QR]
ENGINE ASSEMBLY

REMOVAL
Outline
Remove engine and transaxle assembly with front suspension member from vehicle downward. Separate
front suspension member, and then separate engine and transaxle.
Preparation
1. Release fuel pressure. Refer to EC-49, "FUEL PRESSURE RELEASE" .
2. Drain engine coolant from radiator. Refer to CO-10, "
Changing Engine Coolant" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belt.
3. Remove the following parts.

Hood assembly; Refer to BL-13, "HOOD" .

Undercover and splash guards (RH and LH)

Front road wheels and tires

Battery, battery tray and battery tray bracket; Refer to SC-4, "BATTERY" .

Drive belt; Refer to EM-14, "DRIVE BELTS" .

Air duct (inlet); Refer to EM-17, "AIR CLEANER AND AIR DUCT" .

Air cleaner case (upper) with mass air flow sensor and air duct assembly; Refer to EM-17, "AIR
CLEANER AND AIR DUCT" .

Alternator and alternator bracket; Refer to SC-27, "CHARGING SYSTEM" .

Radiator and radiator cooling fan assembly, reservoir tank of radiator and system hoses; Refer to CO-
13, "RADIATOR" .
4. Disconnect engine room harness connector from ECM side and set it aside for easier work.
5. Disconnect all vacuum hoses and air hoses connected to vehicle side at engine side.
Engine Room LH
1. Disconnect heater hose, and install plug it to prevent engine coolant from draining. Refer to CO-24,
"THERMOSTAT AND WATER CONTROL VALVE" .
2. Disconnect fuel feed hose, and plug it to prevent fuel from draining. Refer to EM-34, "
FUEL INJECTOR
AND FUEL TUBE" .
3. Disconnect control cable from transaxle. Refer to AT- 2 1 3 , "
SHIFT CONTROL SYSTEM" .
4. Disconnect B terminal harness of starter motor. Refer to SC-14, "
STARTING SYSTEM" .
Engine Room RH
1. Remove IPDM E/R and bracket. Refer to PG-17, "IPDM E/R (INTELLIGENT POWER DISTRIBUTION
MODULE ENGINE ROOM)" .
2. Remove A/C compressor with piping connected from engine. Temporarily secure it on vehicle side with a
rope to avoid putting load on it. Refer to ATC-134, "
Removal and Installation of Compressor" .
3. Remove reservoir tank of power steering oil pump. Temporarily secure it on engine side with a rope. Refer
to PS-39, "
HYDRAULIC LINE" .
Vehicle Underbody
1. Remove RH and LH front drive shafts. Refer to FAX-8, "FRONT DRIVE SHAFT" .
2. Remove exhaust front tube. Refer to EX-2, "
EXHAUST SYSTEM" .
3. Remove rear plate cover from oil pan (upper). Then remove bolts fixing drive plate to torque converter.
Refer to EM-26, "
OIL PAN AND OIL STRAINER" and AT- 2 4 1 , "TRANSAXLE ASSEMBLY" .
4. Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side. Refer to AT- 2 4 1 , "
TRAN-
SAXLE ASSEMBLY" .
5. Disconnect connecting rod for front stabilizer. Refer to FSU-5, "
FRONT SUSPENSION ASSEMBLY" .
6. Remove steering lower joint from steering gear. Refer to PS-12, "
STEERING COLUMN" .
7. Remove power steering fluid piping from front suspension member. Refer to PS-39, "
HYDRAULIC LINE"
.
8. Disconnect power steering fluid piping at a point between vehicle and engine, and install plug it to prevent
power steering fluid. Refer to PS-39, "
HYDRAULIC LINE" .

ENGINE ASSEMBLY
EM-79
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM

Removal
1. Install engine slingers into front left of cylinder head and rear right of cylinder head.

Use alternator bracket mounting bolt holes for the front side.
2. Lift with hoist and secure engine in position.
3. Use manual lift table caddy (commercial service tool) or equiva-
lently rigid tool such as transmission jack. Securely support bot-
tom of front suspension member, and simultaneously adjust
hoist tension.
CAUTION:
Put a piece of wood or something similar as the supporting
surface, secure a completely stable condition.
4. Separate RH engine mounting insulator and RH engine mounting bracket.
5. Pull LH engine mounting through-bolt out.
6. Remove front suspension member mounting nuts and bolts. Refer to FSU-5, "
FRONT SUSPENSION
ASSEMBLY" .
7. Remove engine and transaxle assembly with front suspension member from vehicle downward by care-
fully operating supporting tools.
CAUTION:

During the operation, make sure that no part interferes with vehicle side.

Before and during this lifting, always check if any harnesses are left connected.

During the removal operation, always be careful to prevent vehicle from falling off the lift due to
changes in the center of gravity.

If necessary, support vehicle by setting jack or equivalent tool at the rear.
8. Remove power steering oil pump with piping connected from engine. Refer to PS-29, "
POWER STEER-
ING OIL PUMP" .
9. Remove front engine mounting and rear engine mounting through-bolts to remove front suspension mem-
ber.
10. Remove starter motor. Refer to SC-14, "
STARTING SYSTEM" .
11. Remove each engine mounting insulator and each engine mounting bracket from engine, transaxle and
front suspension member.
12. Separate engine and transaxle. Refer to AT- 2 4 1 , "
TRANSAXLE ASSEMBLY" .
INSTALLATION
Note the following, and install in the reverse order of removal.

Do not allow engine oil to get on engine mounting insulator. Be careful not to damage engine mounting
insulator.

When installation directions are specified, install parts according to the direction marks on them referring
to the figure of components. Refer to EM-77, "
Removal and Installation" .

Make sure that each engine mounting insulator is seated properly, and tighten mounting nuts and bolts.Slinger bolts:
Front
: 57.9 N·m (5.9 kg-m, 43 ft-lb)
Rear
: 28.0 N·m (2.9 kg-m, 21 ft-lb)
SBIA0271E
PBIC2484E

EM-80
[QR]
ENGINE ASSEMBLY

INSPECTION AFTER INSTALLATION
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.

Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-14, "
RECOMMENDED FLUIDS AND LUBRICANTS" .

Use procedure below to check for fuel leakage.
–Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–Start engine. With engine speed increased, check again for fuel leakage at connection points.

Run engine to check for unusual noise and vibration.

Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.

Bleed air from lines and hoses of applicable lines, such as in cooling system.

After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
* Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.Item Before starting engine Engine running After engine stopped
Engine coolant Level Leakage Level
Engine oil Level Leakage Level
Other oils and fluid* Level Leakage Level
Fuel Leakage Leakage Leakage
Exhaust gases — Leakage —