2003 NISSAN ALMERA N16 ecm

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION
A
EC
ENGINE CONTROL SYSTEM
QG (WITH EURO-OBD)
INDEX FOR DTC ...................................................... 10
Alphabetical Index .................................................. 10
DTC No. Index ....................................................... 12
PRECAUTIONS ........................................................ 15
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 15
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 15
Precaution .............................................................. 15
Wiring Diagrams and Trouble Diagnosis ................ 18
PREPARATION ......................................................... 19
Special Service Tools ............................................. 19
Commercial Service Tools ...................................... 19
ENGINE CONTROL SYSTEM .................................. 21
System Diagram ..................................................... 21
Vacuum Hose Drawing ........................................... 22
System Chart ......................................................... 23
Multiport Fuel Injection (MFI) System .................... 23
Electronic Ignition (EI) System ............................... 25
Air Conditioning Cut Control ................................... 26
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 27
CAN Communication .............................................. 27
BASIC SERVICE PROCEDURE .............................. 30
Idle Speed and Ignition Timing Check .................... 30
Accelerator Pedal Released Position Learning ...... 31
Throttle Valve Closed Position Learning ................ 31
Idle Air Volume Learning ........................................ 31
Fuel Pressure Check .............................................. 34
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 36
Introduction ............................................................ 36
Two Trip Detection Logic ........................................ 36
Emission-related Diagnostic Information ................ 37
NATS (Nissan Anti-theft System) ........................... 49
Malfunction Indicator (MI) ....................................... 49
OBD System Operation Chart ................................ 52
TROUBLE DIAGNOSIS ............................................ 58
Trouble Diagnosis Introduction ............................... 58DTC Inspection Priority Chart ................................. 62
Fail-safe Chart ........................................................ 63
Basic Inspection ..................................................... 65
Symptom Matrix Chart ............................................ 70
Engine Control Component Parts Location ............ 74
Circuit Diagram ....................................................... 78
ECM Harness Connector Terminal Layout ............. 80
ECM Terminals and Reference Value ..................
... 80
CONSULT-II Function ............................................. 87
Generic Scan Tool (GST) Function ......................... 97
CONSULT-II Reference Value in Data Monitor Mode
... 99
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................102
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .105
Description ............................................................105
Testing Condition ..................................................105
Inspection Procedure ............................................105
Diagnostic Procedure ...........................................106
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................109
Description ............................................................109
Diagnostic Procedure ...........................................109
POWER SUPPLY CIRCUIT FOR ECM ...................110
Wiring Diagram .....................................................110
Diagnostic Procedure ............................................111
Component Inspection ..........................................115
DTC U1000, U1001 CAN COMMUNICATION LINE .116
Description ............................................................116
On Board Diagnosis Logic ....................................116
DTC Confirmation Procedure ...............................116
Wiring Diagram .....................................................117
Diagnostic Procedure ...........................................118
DTC P0011 IVT CONTROL .....................................119
Description ............................................................119
CONSULT-II Reference Value in Data Monitor Mode
.119
On Board Diagnosis Logic ....................................120
DTC Confirmation Procedure ...............................120
Diagnostic Procedure ...........................................121

EC-3
C
D
E
F
G
H
I
J
K
L
M
ECA Component Inspection ......................................... 204
Removal and Installation ...................................... 204
DTC P0222, P0223 TP SENSOR ........................... 205
Component Description ........................................ 205
CONSULT-II Reference Value in Data Monitor Mode
. 205
On Board Diagnosis Logic ................................... 205
DTC Confirmation Procedure ............................... 205
Wiring Diagram .................................................... 207
Diagnostic Procedure ........................................... 208
Component Inspection ......................................... 210
Removal and Installation ...................................... 210
DTC P0226 APP SENSOR ......................................211
Component Description ......................................... 211
CONSULT-II Reference Value in Data Monitor Mode
.. 211
On Board Diagnosis Logic .................................... 211
DTC Confirmation Procedure ................................ 211
Wiring Diagram .................................................... 213
Diagnostic Procedure ........................................... 214
Component Inspection ......................................... 216
Removal and Installation ...................................... 217
DTC P0227, P0228 APP SENSOR ........................ 218
Component Description ........................................ 218
CONSULT-II Reference Value in Data Monitor Mode
. 218
On Board Diagnosis Logic ................................... 218
DTC Confirmation Procedure ............................... 218
Wiring Diagram .................................................... 220
Diagnostic Procedure ........................................... 221
Component Inspection ......................................... 223
Removal and Installation ...................................... 224
DTC P0300 - P0304 MULTIPLE CYLINDER MIS-
FIRE, NO. 1 - 4 CYLINDER MISFIRE ..................... 225
On Board Diagnosis Logic ................................... 225
DTC Confirmation Procedure ............................... 225
Diagnostic Procedure ........................................... 226
DTC P0327, P0328 KS ........................................... 230
Component Description ........................................ 230
On Board Diagnosis Logic ................................... 230
DTC Confirmation Procedure ............................... 230
Wiring Diagram .................................................... 231
Diagnostic Procedure ........................................... 232
Component Inspection ......................................... 233
Removal and Installation ...................................... 233
DTC P0335 CKP SENSOR (POS) .......................... 234
Component Description ........................................ 234
CONSULT-II Reference Value in Data Monitor Mode
. 234
On Board Diagnosis Logic ................................... 234
DTC Confirmation Procedure ............................... 234
Wiring Diagram ...................................................
. 235
Diagnostic Procedure ........................................... 236
Component Inspection ......................................... 238
Removal and Installation ...................................... 239
DTC P0340 CMP SENSOR (PHASE) ..................... 240
Component Description ........................................ 240
On Board Diagnosis Logic ................................... 240
DTC Confirmation Procedure ............................... 240Wiring Diagram .....................................................241
Diagnostic Procedure ...........................................242
Component Inspection ..........................................244
Removal and Installation ......................................245
DTC P0420 THREE WAY CATALYST FUNCTION . 246
On Board Diagnosis Logic ....................................246
DTC Confirmation Procedure ...............................246
Overall Function Check ........................................247
Diagnostic Procedure ...........................................248
DTC P0444 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE ...............................251
Description ............................................................251
CONSULT-II Reference Value in Data Monitor Mode
.251
On Board Diagnosis Logic ....................................252
DTC Confirmation Procedure ...............................252
Wiring Diagram .....................................................253
Diagnostic Procedure ...........................................254
Component Inspection ..........................................256
Removal and Installation ......................................256
DTC P0500 VSS ......................................................257
Description ............................................................257
On Board Diagnosis Logic ....................................257
DTC Confirmation Procedure ...............................257
Overall Function Check ........................................258
Diagnostic Procedure ...........................................259
DTC P0550 PSP SENSOR .....................................260
Component Description ........................................260
CONSULT-II Reference Value in Data Monitor Mode
.260
On Board Diagnosis Logic ....................................260
DTC Confirmation Procedure ...............................260
Wiring Diagram .....................................................261
Diagnostic Procedure ...........................................262
Component Inspection ..........................................264
DTC P0605 ECM .....................................................265
Component Description ........................................265
On Board Diagnosis Logic ....................................265
DTC Confirmation Procedure ...............................265
Diagnostic Procedure ...........................................266
DTC P1065 ECM POWER SUPPLY .......................268
Component Description ........................................268
On Board Diagnosis Logic ....................................268
DTC Confirmation Procedure ...............................268
Wiring Diagram .....................................................269
Diagnostic Procedure ...........................................270
DTC P1111 IVT CONTROL SOLENOID VALVE .....272
Component Description ........................................272
CONSULT-II Reference Value in Data Monitor Mode
.272
On Board Diagnosis Logic ....................................272
DTC Confirmation Procedure ...............................272
Wiring Diagram .....................................................273
Diagnostic Procedure ...........................................274
Component Inspection ..........................................275
Removal and Installation ......................................275
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR .............................................................276
Component Description ........................................276

EC-6
Basic Inspection ...................................................443
Symptom Matrix Chart ..........................................448
Engine Control Component Parts Location ..........452
Circuit Diagram .....................................................456
ECM Harness Connector Terminal Layout ...........458
ECM Terminals and Reference Value ...................458
CONSULT-II Function ...........................................465
CONSULT-II Reference Value in Data Monitor Mode
.475
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................479
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .481
Description ............................................................481
Testing Condition ..................................................481
Inspection Procedure ............................................481
Diagnostic Procedure ...........................................482
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................485
Description ............................................................485
Diagnostic Procedure ...........................................485
POWER SUPPLY CIRCUIT FOR ECM ...................486
Wiring Diagram .....................................................486
Diagnostic Procedure ...........................................487
Component Inspection ..........................................491
DTC U1000, U1001 CAN COMMUNICATION LINE .492
Description ............................................................492
On Board Diagnosis Logic ....................................492
DTC Confirmation Procedure ...............................492
Wiring Diagram .....................................................493
Diagnostic Procedure ...........................................494
DTC P0102, P0103 MAF SENSOR .........................495
Component Description ........................................495
CONSULT-II Reference Value in Data Monitor Mode
.495
On Board Diagnosis Logic ....................................495
DTC Confirmation Procedure ...............................496
Wiring Diagram .....................................................497
Diagnostic Procedure ...........................................498
Component Inspection ..........................................500
Removal and Installation ......................................500
DTC P0117, P0118 ECT SENSOR ..........................501
Component Description ........................................501
On Board Diagnosis Logic ....................................501
DTC Confirmation Procedure ...............................502
Wiring Diagram .....................................................503
Diagnostic Procedure ...........................................504
Component Inspection ..........................................505
Removal and Installation ......................................505
DTC P0132 HO2S1 .................................................506
Component Description ........................................506
CONSULT-II Reference Value in Data Monitor Mode
.506
On Board Diagnosis Logic ....................................506
DTC Confirmation Procedure ...............................507
Wiring Diagram .....................................................508
Diagnostic Procedure ...........................................509
Component Inspection ..........................................510
Removal and Installation ......................................511DTC P0134 HO2S1 ................................................ .512
Component Description ........................................512
CONSULT-II Reference Value in Data Monitor Mode
.512
On Board Diagnosis Logic ....................................512
Overall Function Check .........................................513
Wiring Diagram .....................................................514
Diagnostic Procedure ............................................515
Component Inspection ..........................................516
Removal and Installation .......................................517
DTC P0138 HO2S2 ................................................ .518
Component Description ........................................518
CONSULT-II Reference Value in Data Monitor Mode
.518
On Board Diagnosis Logic ....................................518
DTC Confirmation Procedure ................................518
Wiring Diagram .....................................................520
Diagnostic Procedure ............................................521
Component Inspection ..........................................522
Removal and Installation .......................................523
DTC P0221 TP SENSOR ........................................524
Component Description ........................................524
CONSULT-II Reference Value in Data Monitor Mode
.524
On Board Diagnosis Logic ....................................524
DTC Confirmation Procedure ................................524
Wiring Diagram .....................................................526
Diagnostic Procedure ............................................527
Component Inspection ..........................................529
Removal and Installation .......................................529
DTC P0222, P0223 TP SENSOR ............................530
Component Description ........................................530
CONSULT-II Reference Value in Data Monitor Mode
.530
On Board Diagnosis Logic ....................................530
DTC Confirmation Procedure ................................530
Wiring Diagram .....................................................532
Diagnostic Procedure ............................................533
Component Inspection ..........................................535
Removal and Installation ......................................
.535
DTC P0226 APP SENSOR ......................................536
Component Description ........................................536
CONSULT-II Reference Value in Data Monitor Mode
.536
On Board Diagnosis Logic ....................................536
DTC Confirmation Procedure ................................536
Wiring Diagram .....................................................538
Diagnostic Procedure ............................................539
Component Inspection ..........................................541
Removal and Installation .......................................542
DTC P0227, P0228 APP SENSOR .........................543
Component Description ........................................543
CONSULT-II Reference Value in Data Monitor Mode
.543
On Board Diagnosis Logic ....................................543
DTC Confirmation Procedure ................................543
Wiring Diagram .....................................................545
Diagnostic Procedure ............................................546

EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA Component Inspection ......................................... 548
Removal and Installation ...................................... 549
DTC P0327, P0328 KS ........................................... 550
Component Description ........................................ 550
On Board Diagnosis Logic ................................... 550
DTC Confirmation Procedure ............................... 550
Wiring Diagram .................................................... 551
Diagnostic Procedure ........................................... 552
Component Inspection ......................................... 553
Removal and Installation ...................................... 553
DTC P0335 CKP SENSOR (POS) .......................... 554
Component Description ........................................ 554
CONSULT-II Reference Value in Data Monitor Mode
. 554
On Board Diagnosis Logic ................................... 554
DTC Confirmation Procedure ............................... 554
Wiring Diagram .................................................... 556
Diagnostic Procedure ........................................... 557
Component Inspection ......................................... 559
Removal and Installation ...................................... 560
DTC P0340 CMP SENSOR (PHASE) ..................... 561
Component Description ........................................ 561
On Board Diagnosis Logic ................................... 561
DTC Confirmation Procedure ............................... 561
Wiring Diagram .................................................... 563
Diagnostic Procedure ........................................... 564
Component Inspection ......................................... 566
Removal and Installation ...................................... 567
DTC P0605 ECM .................................................... 568
Component Description ........................................ 568
On Board Diagnosis Logic ................................... 568
DTC Confirmation Procedure ............................... 568
Diagnostic Procedure ........................................... 570
DTC P1065 ECM POWER SUPPLY ....................... 571
Component Description ........................................ 571
On Board Diagnosis Logic ................................... 571
DTC Confirmation Procedure ............................... 571
Wiring Diagram .................................................... 572
Diagnostic Procedure ........................................... 573
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR ............................................................ 575
Component Description ........................................ 575
On Board Diagnosis Logic ................................... 575
DTC Confirmation Procedure ............................... 575
Diagnostic Procedure ........................................... 576
Removal and Installation ...................................... 577
DTC P1122 ELECTRIC THROTTLE CONTROL
FUNCTION .............................................................. 578
Description ..........................................................
. 578
On Board Diagnosis Logic ................................... 578
DTC Confirmation Procedure ............................... 578
Wiring Diagram .................................................... 579
Diagnostic Procedure ........................................... 580
Component Inspection ......................................... 584
Removal and Installation ...................................... 584
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY .................................................................... 585
Component Description ........................................ 585
CONSULT-II Reference Value in Data Monitor Mode .585
On Board Diagnosis Logic ....................................585
DTC Confirmation Procedure ...............................585
Wiring Diagram .....................................................587
Diagnostic Procedure ...........................................588
Component Inspection ..........................................590
DTC P1128 THROTTLE CONTROL MOTOR .........591
Component Description ........................................591
On Board Diagnosis Logic ....................................591
DTC Confirmation Procedure ...............................591
Wiring Diagram .....................................................592
Diagnostic Procedure ...........................................593
Component Inspection ..........................................594
Removal and Installation ......................................595
DTC P1217 ENGINE OVER TEMPERATURE ........596
System Description ...............................................596
CONSULT-II Reference Value in Data Monitor Mode
.596
On Board Diagnosis Logic ....................................597
Overall Function Check ........................................597
Wiring Diagram .....................................................599
Diagnostic Procedure ...........................................600
Main 12 Causes of Overheating ...........................605
Component Inspection ..........................................606
DTC P1223, P1224 TP SENSOR ............................607
Component Description ........................................607
CONSULT-II Reference Value in Data Monitor Mode
.607
On Board Diagnosis Logic ....................................607
DTC Confirmation Procedure ...............................607
Wiring Diagram .....................................................609
Diagnostic Procedure ...........................................610
Component Inspection ..........................................612
Removal and Installation ......................................612
DTC P1225 TP SENSOR ........................................613
Component Description ........................................613
On Board Diagnosis Logic ....................................613
DTC Confirmation Procedure ...............................613
Diagnostic Procedure ...........................................614
Removal and Installation ......................................614
DTC P1226 TP SENSOR .......................................
.615
Component Description ........................................615
On Board Diagnosis Logic ....................................615
DTC Confirmation Procedure ...............................615
Diagnostic Procedure ...........................................616
Removal and Installation ......................................616
DTC P1227, P1228 APP SENSOR .........................617
Component Description ........................................617
CONSULT-II Reference Value in Data Monitor Mode
.617
On Board Diagnosis Logic ....................................617
DTC Confirmation Procedure ...............................617
Wiring Diagram .....................................................619
Diagnostic Procedure ...........................................620
Component Inspection ..........................................622
Removal and Installation ......................................623
DTC P1229 SENSOR POWER SUPPLY ................624
On Board Diagnosis Logic ....................................624
DTC Confirmation Procedure ...............................624

EC-10
[QG (WITH EURO-OBD)]
INDEX FOR DTC
[QG (WITH EURO-OBD)]INDEX FOR DTCPFP:00024
Alphabetical IndexEBS00K2T
Check if the vehicle is a model with Euro-OBD (E-OBD) system or not by the “Type approval number” on the
identification plate. Refer to GI-39.
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-116, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
×: Applicable –: Not applicable
Items
(CONSULT-II screen terms)DTC*
1
TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3
A/T 1ST GR FNCTN P0731 0731 2×AT-133
A/T 2ND GR FNCTN P0732 0732 2×AT-139
A/T 3RD GR FNCTN P0733 0733 2×AT-145
A/T 4TH GR FNCTN P0734 0734 2×AT-151
APP SEN 1/CIRC P0227 0227 1×EC-218
APP SEN 1/CIRC P0228 0228 1×EC-218
APP SEN 2/CIRC P1227 1227 1×EC-345
APP SEN 2/CIRC P1228 1228 1×EC-345
APP SENSOR P0226 0226 1×EC-211
ATF TEMP SEN/CIRC P0710 0710 2×AT- 11 7
BRAKE SW/CIRCUIT P1805 1805 2 –EC-360
CAN COMM CIRCUIT U1000
1000*51×EC-116
CAN COMM CIRCUIT U1001
1001*52–EC-116
CKP SEN/CIRCUIT P0335 0335 2×EC-234
CMP SEN/CIRC-B1 P0340 0340 2×EC-240
CTP LEARNING P1225 1225 2 –EC-341
CTP LEARNING P1226 1226 2 –EC-343
CYL 1 MISFIRE P0301 0301 2×EC-225
CYL 2 MISFIRE P0302 0302 2×EC-225
CYL 3 MISFIRE P0303 0303 2×EC-225
CYL 4 MISFIRE P0304 0304 2×EC-225
ECM P0605 0605 1 or 2× or –EC-265
ECM BACK UP/CIRC P1065 1065 2×EC-268
ECT SEN/CIRCUIT P0117 0117 1×EC-144
ECT SEN/CIRCUIT P0118 0118 1×EC-144
ENG OVER TEMP P1217 1217 1×EC-324
ENGINE SPEED SIG P0725 0725 1×AT-129
ETC ACTR P1121 1121 1 or 2×EC-276
ETC FUNCTION/CIRC P1122 1122 1×EC-278
ETC MOT P1128 1128 1×EC-291
ETC MOT PWR P1124 1124 1×EC-285
ETC MOT PWR P1126 1126 1×EC-285
FUEL SYS-LEAN-B1 P0171 0171 2×EC-186
FUEL SYS-RICH-B1 P0172 0172 2×EC-193
HO2S1 (B1) P0132 0132 2×EC-149

INDEX FOR DTC
EC-11
[QG (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
ECHO2S1 (B1) P0133 0133 2×EC-155
HO2S1 (B1) P0134 0134 2×EC-165
HO2S1 (B1) P1143 1143 2×EC-296
HO2S1 (B1) P1144 1144 2×EC-302
HO2S1 HTR (B1) P0031 0031 2×EC-122
HO2S1 HTR (B1) P0032 0032 2×EC-122
HO2S2 (B1) P0138 0138 2×EC-172
HO2S2 (B1) P0139 0139 2×EC-178
HO2S2 (B1) P1146 1146 2×EC-308
HO2S2 (B1) P1147 1147 2×EC-316
HO2S2 HTR (B1) P0037 0037 2×EC-128
HO2S2 HTR (B1) P0038 0038 2×EC-128
IAT SEN/CIRCUIT P0112 0112 2×EC-140
IAT SEN/CIRCUIT P0113 0113 2×EC-140
INT/V TIM CONT-B1 P0011 0011 2 –EC-119
INT/V TIM V/CIR-B1 P1111 1111 2×EC-272
KNOCK SEN/CIRC-B1 P0327 0327 2 –EC-230
KNOCK SEN/CIRC-B1 P0328 0328 2 –EC-230
L/PRESS SOL/CIRC P0745 0745 2×AT- 1 6 4
MAF SEN/CIRCUIT P0102 0102 1×EC-134
MAF SEN/CIRCUIT P0103 0103 1×EC-134
MULTI CYL MISFIRE P0300 0300 2×EC-225
NATS MALFUNCTION P1610 - P1615 1610 - 1615 2 –EC-49
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.No DTC
Flashing*4–
Flashing*4EC-50
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.P0000 0000––—
O/R CLTCH SOL/CIRC P1760 1760 2×AT- 1 8 7
PNP SW/CIRC P0705 0705 2×AT- 111
P-N POS SW/CIRCUIT P1706 1706 2×EC-356
PURG VOLUME CONT/V P0444 0444 2×EC-251
PW ST P SEN/CIRC P0550 0550 2 –EC-260
SENSOR POWER/CIRC P1229 1229 1×EC-352
SFT SOL A/CIRC P0750 0750 1×AT- 1 7 1
SFT SOL B/CIRC P0755 0755 1×AT- 1 7 6
TCC SOLENOID/CIRC P0740 0740 2×AT- 1 5 9
TP SEN 1/CIRC P0222 0222 1×EC-205
TP SEN 1/CIRC P0223 0223 1×EC-205
TP SEN 2/CIRC P1223 1223 1×EC-335
TP SEN 2/CIRC P1224 1224 1×EC-335
TP SENSOR P0221 0221 1×EC-199
TPV SEN/CIRC A/T P1705 1705 1×AT- 1 8 1
Items
(CONSULT-II screen terms)DTC*
1
TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3

EC-12
[QG (WITH EURO-OBD)]
INDEX FOR DTC
*1: 1st trip DTC No. is the same as DTC No.
*2: These numbers are prescribed by ISO 15031-5.
*3: In Diagnostic Test Mode II (Self-diagnostic results), these numbers are controlled by NISSAN.
*4: When engine is running.
*5: The troubleshooting for this DTC needs CONSULT-II.
*6: When the fail-safe operations for both self-diagnoses occur, the MI illuminates.
DTC No. IndexEBS00K2U
Check if the vehicle is a model with Euro-OBD (E-OBD) system or not by the “Type approval number” on the
identification plate. Refer to GI-39.
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-116, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
×: Applicable –: Not applicable TW CATALYST SYS-B1 P0420 0420 2×EC-246
VEH SPD SEN/CIR AT*6P0720 0720 2×AT-123
VEH SPEED SEN/CIRC P0500 0500 2×EC-257
Items
(CONSULT-II screen terms)DTC*
1
TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3
DTC*1
Items
(CONSULT-II screen terms)TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3
No DTC
Flashing*4NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.–
Flashing*4EC-50
U1000
1000*5CAN COMM CIRCUIT 1×EC-116
U1001
1001*5CAN COMM CIRCUIT 2 –EC-116
P0000 0000NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED.––—
P0011 0011 INT/V TIM CONT-B1 2 –EC-119
P0031 0031 HO2S1 HTR (B1) 2×EC-122
P0032 0032 HO2S1 HTR (B1) 2×EC-122
P0037 0037 HO2S2 HTR (B1) 2×EC-128
P0038 0038 HO2S2 HTR (B1) 2×EC-128
P0102 0102 MAF SEN/CIRCUIT 1×EC-134
P0103 0103 MAF SEN/CIRCUIT 1×EC-134
P0112 0112 IAT SEN/CIRCUIT 2×EC-140
P0113 0113 IAT SEN/CIRCUIT 2×EC-140
P0117 0117 ECT SEN/CIRCUIT 1×EC-144
P0118 0118 ECT SEN/CIRCUIT 1×EC-144
P0132 0132 HO2S1 (B1) 2×EC-149
P0133 0133 HO2S1 (B1) 2×EC-155
P0134 0134 HO2S1 (B1) 2×EC-165
P0138 0138 HO2S2 (B1) 2×EC-172
P0139 0139 HO2S2 (B1) 2×EC-178
P0171 0171 FUEL SYS-LEAN-B1 2×EC-186
P0172 0172 FUEL SYS-RICH-B1 2×EC-193
P0221 0221 TP SENSOR 1×EC-199

INDEX FOR DTC
EC-13
[QG (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
MA
ECP0222 0222 TP SEN 1/CIRC 1×EC-205
P0223 0223 TP SEN 1/CIRC 1×EC-205
P0226 0226 APP SENSOR 1×EC-211
P0227 0227 APP SEN 1/CIRC 1×EC-218
P0228 0228 APP SEN 1/CIRC 1×EC-218
P0300 0300 MULTI CYL MISFIRE 2×EC-225
P0301 0301 CYL 1 MISFIRE 2×EC-225
P0302 0302 CYL 2 MISFIRE 2×EC-225
P0303 0303 CYL 3 MISFIRE 2×EC-225
P0304 0304 CYL 4 MISFIRE 2×EC-225
P0327 0327 KNOCK SEN/CIRC-B1 2 –EC-230
P0328 0328 KNOCK SEN/CIRC-B1 2 –EC-230
P0335 0335 CKP SEN/CIRCUIT 2×EC-234
P0340 0340 CMP SEN/CIRC-B1 2×EC-240
P0420 0420 TW CATALYST SYS-B1 2×EC-246
P0444 0444 PURG VOLUME CONT/V 2×EC-251
P0500 0500 VEH SPEED SEN/CIRC 2×EC-257
P0550 0550 PW ST P SEN/CIRC 2 –EC-260
P0605 0605 ECM 1 or 2× or –EC-265
P0705 0705 PNP SW/CIRC 2×AT- 111
P0710 0710 ATF TEMP SEN/CIRC 2×AT- 11 7
P0720 0720
VEH SPD SEN/CIRC AT*62×AT-123
P0725 0725 ENGINE SPEED SIG 2×AT-129
P0731 0731 A/T 1ST GR FNCTN 2×AT-133
P0732 0732 A/T 2ND GR FNCTN 2×AT-139
P0733 0733 A/T 3RD GR FNCTN 2×AT-145
P0734 0734 A/T 4TH GR FNCTN 2×AT-151
P0740 0740 TCC SOLENOID/CIRC 2×AT-159
P0745 0745 L/PRESS SOL/CIRC 2×AT-164
P0750 0750 SFT SOL A/CIRC 1×AT-171
P0755 0755 SFT SOL B/CIRC 1×AT-176
P1065 1065 ECM BACK UP/CIRC 2×EC-268
P 1111 1111 I N T / V T I M V / C I R - B 1 2×EC-272
P1121 1121 ETC ACTR 1 or 2×EC-276
P1122 1122 ETC FUNCTION/CIRC 1×EC-278
P1124 1124 ETC MOT PWR 1×EC-285
P1126 1126 ETC MOT PWR 1×EC-285
P1128 1128 ETC MOT 1×EC-291
P1143 1143 HO2S1 (B1) 2×EC-296
P1144 1144 HO2S1 (B1) 2×EC-302
P1146 1146 HO2S2 (B1) 2×EC-308
P1147 1147 HO2S2 (B1) 2×EC-316
DTC*1
Items
(CONSULT-II screen terms)TripMI lighting
upReference page
CONSULT-II
GST*
2ECM*3