2003 Hyundai H-1 (Grand Starex) headlight bulb

2-11
INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
C150A01P-GATTURN SIGNAL SWITCH
TURN SIGNAL SWITCH TURN SIGNAL SWITCH
TURN SIGNAL SWITCH
TURN SIGNAL SWITCH
C140A01P-GAT
MULTI-FUNCTION LIGHT SWITCH
MULTI-FUNCTION LIGHT SWITCH MULTI-FUNCTION LIGHT SWITCH
MULTI-FUNCTION LIGHT SWITCH
MULTI-FUNCTION LIGHT SWITCH
Pulling down on the lever causes the turn
signals on the left side of the car to blink. Pushing upward on the lever causes the turnsignals on the right side of the car to blink. Asthe turn is completed, the lever will automati-cally return to the center position and turn offthe turn signals at the same time. If either turnsignal indicator light blinks more rapidly thanusual, goes on but does not blink, or does notgo on at all, there is a malfunction in thesystem. Check for a burned-out fuse or bulb orsee your Hyundai dealer.
Rotate the switch to turn on the lights.
1. Lights off
2. Position, tail, licence-plate, and instrument panel lamps on
3. Headlights on To operate the headlights, turn the barrel onthe end of the multifunction switch.
Parking light auto cut (If installed)
Parking light auto cut (If installed) Parking light auto cut (If installed)
Parking light auto cut (If installed)
Parking light auto cut (If installed)
If you do not turn the parking lights "OFF" after
driving, the parking light will automatically shut"OFF" when the driver's door is opened.
To turn them "ON" again you must simply turn
the ignition key to the "ON" position. C160A01P-GAT
HIGH-BEAM SWITCH
HIGH-BEAM SWITCH HIGH-BEAM SWITCH
HIGH-BEAM SWITCH
HIGH-BEAM SWITCH
To turn on the headlight high beams, push the
lever forward (away from you). The High BeamIndicator Light will come on at the same time.For low beams, pull the lever back toward you.
C170A01P-GATPASSING SWITCH
PASSING SWITCH PASSING SWITCH
PASSING SWITCH
PASSING SWITCH
HSR2114HSR2113HSR2112
1 2
3
HSR2115

IN CASE OF EMERGENCY
IN CASE OF EMERGENCY IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
4-16 A bulb should only be replaced with a new bulb of the same rating and type. The designationcan be found on the base of the bulb. Headlight, upper/lower beam ................ 60/55WFront turn-signal lamps ................................ 21WPosition lamps ............................................... 5WRear turn-signal lamps ................................. 21W Reversing lamps .......................................... 21W Licence-plate lamps ....................................... 5WStop and tail lamps ................................. 21/5WFront fog lamp .............................................. 55WSide repeater lamp ....................................... 5WRear fog lamp ............................................ 21W
E130D01P-1
Truck
E130B01P-1
E130C01P-1
Truck
Minibus/Van
E130B01P-GAT Bulb capacity
Bulb capacity Bulb capacity
Bulb capacity
Bulb capacity
E130A01P-1
Minibus/Van
E130A02P-GAT
REPLACEMENT OF LAMP BULBS
REPLACEMENT OF LAMP BULBS REPLACEMENT OF LAMP BULBS
REPLACEMENT OF LAMP BULBS
REPLACEMENT OF LAMP BULBS
Before replacing a bulb, be sure the light is off.
Do not touch the glass part of the new bulb with your bare fingers; the skin oil left on the glasswill evaporate when the bulb gets hot and thevapor will condense on the reflector and dim thesurface.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Keep the lamps out of contact with petro-
Keep the lamps out of contact with petro- Keep the lamps out of contact with petro-
Keep the lamps out of contact with petro-
Keep the lamps out of contact with petro- leum product, such as oil, gasoline, etc.
leum product, such as oil, gasoline, etc. leum product, such as oil, gasoline, etc.
leum product, such as oil, gasoline, etc.
leum product, such as oil, gasoline, etc.(2)(2)
(2)(2)
(2)
Never use a fuse with a capacity larger
Never use a fuse with a capacity larger Never use a fuse with a capacity larger
Never use a fuse with a capacity larger
Never use a fuse with a capacity larger
than that specified or any substitute, such
than that specified or any substitute, such than that specified or any substitute, such
than that specified or any substitute, such
than that specified or any substitute, such
as wire, foil, etc.;doing so will cause the
as wire, foil, etc.;doing so will cause the as wire, foil, etc.;doing so will cause the
as wire, foil, etc.;doing so will cause the
as wire, foil, etc.;doing so will cause the
circuit wiring to heat up and can cause a
circuit wiring to heat up and can cause a circuit wiring to heat up and can cause a
circuit wiring to heat up and can cause a
circuit wiring to heat up and can cause a
fire.fire.
fire.fire.
fire.

IN CASE OF EMERGENCY
IN CASE OF EMERGENCY IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
4-17
1) Horizontal line dimension from ground
MINIBUS 2WD:849 mm (33.43 in.) 4WD:972 mm (38.27 in.)
VAN(2WD) : 855 mm (33.66 in.)
TRUCK Long Wheel base
:847 mm (33.35 in.)Extra long Wheel base:845 mm (33.27 in.)
2) Distance between each vertical line.
MINIBUS/VAN(2WD/4WD):1300mm (51.18 in.)
TRUCK (Long wheel base/Extra long
wheel base) : 1272 mm (50.08 in.)
3) Distance between the headlights and the wall that the lights are tested against: 3000 mm (118.11 in)
And then, draw the parallel line at 30 mm (1.18 in.) place under the horizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with a phillips screwdriver - VERTICAL AIMING
8. Adjust each cut-off line of the low beam to the each vertical line with a phillips screw- driver - HORIZONTAL AIMING.
G290A03P-AATHEADLIGHT AIMING ADJUSTMENT
HEADLIGHT AIMING ADJUSTMENT HEADLIGHT AIMING ADJUSTMENT
HEADLIGHT AIMING ADJUSTMENT
HEADLIGHT AIMING ADJUSTMENT
G290A01P-1
Before performing aiming adjustment, make sure of the following.
1. Keep all tires inflated to the correct pres- sure.
2. Place the vehicle on level ground and press the front bumper & rear bumper down sev-eral times.
3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, andspare tire, jack, and tools).
4. Clean the head lights lens and turn on the headlight (Low beam).
5. Open the hood.
6. Draw the vertical line (through the center of each headlight) and the horizontal line (through the center of each headlight) on theaiming screen.
Horizontalaiming
Verticalaiming
G270A01S-AAT
HEADLIGHT BULB
HEADLIGHT BULB HEADLIGHT BULB
HEADLIGHT BULB
HEADLIGHT BULB
Replacement instructions:
Replacement instructions: Replacement instructions:
Replacement instructions:
Replacement instructions:
1. Allow the bulb to cool. Wear eye protection.
2. Always grasp the bulb by its plastic base,
avoid touching the glass.
3. Disconnect the power cord from the bulb base in the back of the headlight.
4. Push the bulb spring for removing the head- light bulb.
5. Remove the protective cap from the re- placement bulb and install the new bulb by matching the plastic base with the headlighthole. Retighten the bulb spring and recon-nect the power cord.
6. Use the protective cap and carton to dis- pose of the old bulb.
7. Check for proper headlight aim.
WARNING
WARNING WARNING
WARNING
WARNING
This halogen bulb contains gas under pres-
This halogen bulb contains gas under pres- This halogen bulb contains gas under pres-
This halogen bulb contains gas under pres-
This halogen bulb contains gas under pres- sure and if impacted could shatter, resulting
sure and if impacted could shatter, resulting sure and if impacted could shatter, resulting
sure and if impacted could shatter, resulting
sure and if impacted could shatter, resulting
in flying fragments. Always wear eye pro-
in flying fragments. Always wear eye pro- in flying fragments. Always wear eye pro-
in flying fragments. Always wear eye pro-
in flying fragments. Always wear eye pro-
tection when servicing the bulb. Protect the
tection when servicing the bulb. Protect the tection when servicing the bulb. Protect the
tection when servicing the bulb. Protect the
tection when servicing the bulb. Protect the
bulb against abrasions or scratches and
bulb against abrasions or scratches and bulb against abrasions or scratches and
bulb against abrasions or scratches and
bulb against abrasions or scratches and
against liquids when lighted. Turn on the
against liquids when lighted. Turn on the against liquids when lighted. Turn on the
against liquids when lighted. Turn on the
against liquids when lighted. Turn on the
bulb only when installed in a headlight. Re-
bulb only when installed in a headlight. Re- bulb only when installed in a headlight. Re-
bulb only when installed in a headlight. Re-
bulb only when installed in a headlight. Re-
place the headlight if damaged or cracked.
place the headlight if damaged or cracked. place the headlight if damaged or cracked.
place the headlight if damaged or cracked.
place the headlight if damaged or cracked.
Keep the bulb out of the reach of children
Keep the bulb out of the reach of children Keep the bulb out of the reach of children
Keep the bulb out of the reach of children
Keep the bulb out of the reach of children
and dispose of the used bulb with care.
and dispose of the used bulb with care. and dispose of the used bulb with care.
and dispose of the used bulb with care.
and dispose of the used bulb with care.

IN CASE OF EMERGENCY
IN CASE OF EMERGENCY IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
4-18 E130D01P-GAT
Front combination lamps
Front combination lamps Front combination lamps
Front combination lamps
Front combination lamps
Remove the bezel attaching screw from the front combination lamp. Then turn the bulb socket counterclockwise to remove it. To remove the bulb of the side turn-signal lamps, turn the bulb counterclockwise whilepressing it inward.
E130A01P-1
Truck
Minbus/Van
E130C01P-1
"H"; Horizontal center line of headlights from ground.
MINIBUS 2
WD:849 mm (33.43 in.)
4WD:972 mm (38.27 in.)
VAN(2WD) : 855 mm (33.66 in.)
TRUCK Long Wheel base
:847 mm (33.35 in.) Extra long Wheel base:845 mm (33.27 in.)
"W"; Distance between each headlight center. MINIBUS/VAN(2WD/4WD):1300mm (51.18 in.)Truck (Long wheel base/Extra longwheel base) : 1272 mm (50.08 in.) "L"; Distance between the headlights and the wall that the lights are tested against : 3,000 mm (118.11 in.).
If the vehicle has had front body repair and the
headlight assembly has been replaced, the head- light aiming should be checked using the aimingscreen as shown in the illustration. Turn on theheadlight switch. (Low Beam Position)
1. Adjust headlights so that main axis of light is parallel to center line of the body and is aligned with point "P" shown in the illustra-tion.
2. Dotted lines in the illustration show center of headlights.
G290B02P-AAT
Adjustment After Headlight Assembly
Adjustment After Headlight Assembly Adjustment After Headlight Assembly
Adjustment After Headlight Assembly
Adjustment After Headlight Assembly
Replacement
Replacement Replacement
Replacement
Replacement
G290B01Y
Vertical line
Cut-off line Ground line
Horizontal line
LW
H
H "P"
15mm (0.59in.)30mm(1.18in.)