2003 Hyundai H-1 (Grand Starex) clutch

STARTING & OPERATING
STARTING & OPERATING STARTING & OPERATING
STARTING & OPERATING
STARTING & OPERATING
3-2 3. On vehicles equipped with the diesel pre-
heat indication lamp, turn the ignition key to the "ON" position. The diesel-preheat indi-cation lamp will first illuminate in amber, andthen after a short time, the amber illumina-tion will go off, indicating that preheating iscompleted.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
If the engine were not started 10 seconds
If the engine were not started 10 seconds If the engine were not started 10 seconds
If the engine were not started 10 seconds
If the engine were not started 10 seconds
after the preheating is completed, turn the
after the preheating is completed, turn the after the preheating is completed, turn the
after the preheating is completed, turn the
after the preheating is completed, turn the
ignition key once more to the "LOCK" posi-
ignition key once more to the "LOCK" posi- ignition key once more to the "LOCK" posi-
ignition key once more to the "LOCK" posi-
ignition key once more to the "LOCK" posi-
tion, and then to the "ON" position, in order
tion, and then to the "ON" position, in order tion, and then to the "ON" position, in order
tion, and then to the "ON" position, in order
tion, and then to the "ON" position, in order
to preheat again.
to preheat again. to preheat again.
to preheat again.
to preheat again.
TO LOCK
TO LOCK TO LOCK
TO LOCK
TO LOCK Remove the key at the "LOCK" position.Slightly turn the steering wheel until it is locked.
TO UNLOCK
TO UNLOCK TO UNLOCK
TO UNLOCK
TO UNLOCKTurn the key to the "ACC" position while mov-
ing the steering wheel slightly.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
If the key is accidentally removed, the steer-
If the key is accidentally removed, the steer- If the key is accidentally removed, the steer-
If the key is accidentally removed, the steer-
If the key is accidentally removed, the steer-ing wheel will lock making it impossible to
ing wheel will lock making it impossible to ing wheel will lock making it impossible to
ing wheel will lock making it impossible to
ing wheel will lock making it impossible to
control the vehicle.
control the vehicle. control the vehicle.
control the vehicle.
control the vehicle. D030A02P-GAT
STARTING THE ENGINE
STARTING THE ENGINE STARTING THE ENGINE
STARTING THE ENGINE
STARTING THE ENGINE
D030A02P-GAG
1. Apply the parking brake.
C050B01HP
Amber lamp OFF
Amber lamp ON
D030A01P-1
GT30020A
D020B01P-GAT How to lock and unlock the steering
How to lock and unlock the steering How to lock and unlock the steering
How to lock and unlock the steering
How to lock and unlock the steering
wheel
wheel wheel
wheel
wheel
2. If your Hyundai is equipped with a manual
transmission, place the shift lever in neutral and depress the clutch pedal fully. If yourHyundai has an automatic transmission,place the shift lever in "P" (park).

STARTING & OPERATING
STARTING & OPERATING STARTING & OPERATING
STARTING & OPERATING
STARTING & OPERATING
3-4 D050C02P-GAT
Good Driving Practices
Good Driving Practices Good Driving Practices
Good Driving Practices
Good Driving Practices
o Never take the vehicle out of gear and coast
down a hill. This is extremely hazardous. Always leave the vehicle in gear.
o Don't "ride" the brakes. This can cause them to overheat and malfunction. Instead,when you are driving down a long hill, slowdown and shift to a lower gear. When you dothis, engine braking will help slow the car.
o Slow down before shifting to a lower gear. This will help avoid over-running the engine,which can cause damage.
o Slow down when you encounter cross winds. This gives you much better control of yourcar.
o Be sure the vehicle is completely stopped before you attempt to shift into reverse. Thetransmission can be damaged if you do not.To shift into reverse, depress the clutch,move the shift lever to neutral, wait threeseconds, then shift to the reverse position.
o Exercise extreme caution when driving on a slippery surface. Be especially careful whenbraking, accelerating or shifting gears. On a slippery surface, an abrupt change in engine speed can cause the drive wheels tolose traction and the vehicle to go out ofcontrol.
D050A02P-GAT
MANUAL TRANSMISSION
MANUAL TRANSMISSION MANUAL TRANSMISSION
MANUAL TRANSMISSION
MANUAL TRANSMISSION
YN20060A
The shift pattern is shown on the gearshift lever knob. Be sure to always fully depress the clutchpedal before attempting to shift to lever. To shift into reverse from 5th gear,move the gearshift lever to neutral, and then shift it intoreverse.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
oo
oo
o
During cold weather, shifting may be dif-
During cold weather, shifting may be dif- During cold weather, shifting may be dif-
During cold weather, shifting may be dif-
During cold weather, shifting may be dif-
ficult until the transmission lubricant has
ficult until the transmission lubricant has ficult until the transmission lubricant has
ficult until the transmission lubricant has
ficult until the transmission lubricant has
warmed up. This is normal and not harm-
warmed up. This is normal and not harm- warmed up. This is normal and not harm-
warmed up. This is normal and not harm-
warmed up. This is normal and not harm-
ful to the transmission.
ful to the transmission. ful to the transmission.
ful to the transmission.
ful to the transmission.
oo
oo
o
If you 've come to a complete stop and
If you 've come to a complete stop and If you 've come to a complete stop and
If you 've come to a complete stop and
If you 've come to a complete stop and
it's hard to shift into 1st or R(Reverse),
it's hard to shift into 1st or R(Reverse), it's hard to shift into 1st or R(Reverse),
it's hard to shift into 1st or R(Reverse),
it's hard to shift into 1st or R(Reverse),
put the shift lever in N(Neutral) position
put the shift lever in N(Neutral) position put the shift lever in N(Neutral) position
put the shift lever in N(Neutral) position
put the shift lever in N(Neutral) position
and let up on the clutch. Press the clutch
and let up on the clutch. Press the clutch and let up on the clutch. Press the clutch
and let up on the clutch. Press the clutch
and let up on the clutch. Press the clutch
pedal back down, and then shift into 1st
pedal back down, and then shift into 1st pedal back down, and then shift into 1st
pedal back down, and then shift into 1st
pedal back down, and then shift into 1st
or R(Reverse) gear position.
or R(Reverse) gear position. or R(Reverse) gear position.
or R(Reverse) gear position.
or R(Reverse) gear position. D050B01P-GAT
Using the Clutch
Using the Clutch Using the Clutch
Using the Clutch
Using the Clutch
The clutch should be pressed all the way to the floor before shifting, then released slowly. Donot rest your foot on the clutch pedal whiledriving. This can cause unnecessary wear. Do not partially engage the clutch to hold the vehicle on an incline. This causes unnecessarywear. Use the parking brake to hold the vehicle on an incline. Do not operate the clutch pedal rapidlyand repeatedly.
oo
oo
o Do not use the shift lever as a handrest
Do not use the shift lever as a handrest Do not use the shift lever as a handrest
Do not use the shift lever as a handrest
Do not use the shift lever as a handrest
during driving, as this can result in pre-
during driving, as this can result in pre- during driving, as this can result in pre-
during driving, as this can result in pre-
during driving, as this can result in pre-
mature wear of the transmission shift
mature wear of the transmission shift mature wear of the transmission shift
mature wear of the transmission shift
mature wear of the transmission shift
forks.
forks. forks.
forks.
forks.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Do not move the gearshift lever into reverse
Do not move the gearshift lever into reverse Do not move the gearshift lever into reverse
Do not move the gearshift lever into reverse
Do not move the gearshift lever into reverse
while the vehicle is moving forward; doing
while the vehicle is moving forward; doing while the vehicle is moving forward; doing
while the vehicle is moving forward; doing
while the vehicle is moving forward; doing
so will damage the transmission.
so will damage the transmission. so will damage the transmission.
so will damage the transmission.
so will damage the transmission.

3-9
STARTING & OPERATING
STARTING & OPERATING STARTING & OPERATING
STARTING & OPERATING
STARTING & OPERATING
D090A01P-GAG
D090A01P-GAT
FOUR-WHEEL DRIVE (4WD)
FOUR-WHEEL DRIVE (4WD) FOUR-WHEEL DRIVE (4WD)
FOUR-WHEEL DRIVE (4WD)
FOUR-WHEEL DRIVE (4WD)
(Minibus, Van) (If installed)
(Minibus, Van) (If installed) (Minibus, Van) (If installed)
(Minibus, Van) (If installed)
(Minibus, Van) (If installed) You can send your engine power to all front and rear wheels for maximum power. 4WD is usefulwhen you drive in snow, mud, ice, mountainousor sandy areas where good traction is required,or when your wheels lose traction using two-wheel drive.
Switch position
Switch position Switch position
Switch position
Switch position
2H(Rear-wheel drive)
2H(Rear-wheel drive) 2H(Rear-wheel drive)
2H(Rear-wheel drive)
2H(Rear-wheel drive) When driving on normal roads and highway. 4H(High range 4-wheel drive)
4H(High range 4-wheel drive) 4H(High range 4-wheel drive)
4H(High range 4-wheel drive)
4H(High range 4-wheel drive)
When driving deep snow, sand or rough roads
with normal speed. The 4WD indication light(HI) will be turned on to remind you that you are inthe 4H mode.
4L(Low range 4-wheel drive)
4L(Low range 4-wheel drive) 4L(Low range 4-wheel drive)
4L(Low range 4-wheel drive)
4L(Low range 4-wheel drive)
When driving up or descending steep slopes or
rough roads such as muddy road. Especiallywhen increased drive power is required.
The indication light(LO) will be turned on to
remind you that you are in the 4L mode.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Do not select 4WD mode on dry paved roads.
Do not select 4WD mode on dry paved roads. Do not select 4WD mode on dry paved roads.
Do not select 4WD mode on dry paved roads.
Do not select 4WD mode on dry paved roads. Especially on dry high way, never select the
Especially on dry high way, never select the Especially on dry high way, never select the
Especially on dry high way, never select the
Especially on dry high way, never select the
4WD(4H or 4L).
4WD(4H or 4L). 4WD(4H or 4L).
4WD(4H or 4L).
4WD(4H or 4L).
Four-wheel driving on dry paved roads for a
Four-wheel driving on dry paved roads for a Four-wheel driving on dry paved roads for a
Four-wheel driving on dry paved roads for a
Four-wheel driving on dry paved roads for along period will increase the fuel consump-
long period will increase the fuel consump- long period will increase the fuel consump-
long period will increase the fuel consump-
long period will increase the fuel consump-
tion with possible noise generation and ear-
tion with possible noise generation and ear- tion with possible noise generation and ear-
tion with possible noise generation and ear-
tion with possible noise generation and ear-
ly tire wear. In addition, differential oil tem-
ly tire wear. In addition, differential oil tem- ly tire wear. In addition, differential oil tem-
ly tire wear. In addition, differential oil tem-
ly tire wear. In addition, differential oil tem-
perature increases with possible driving
perature increases with possible driving perature increases with possible driving
perature increases with possible driving
perature increases with possible driving
system part wear.
system part wear. system part wear.
system part wear.
system part wear.
D090D02P-GAT
Transfer shift switch operation
Transfer shift switch operation Transfer shift switch operation
Transfer shift switch operation
Transfer shift switch operation
By selecting the transfer shift switch(4H, 4L),
the both axles of the vehicle are rigidly connect- ed with each other. This improves the tractioncharacteristics.
2H 2H
2H 2H
2H








4H 4H
4H 4H
4H
Select the 4H mode switch at speed below
60~70 km/h. It is not necessary to depress theclutch pedal (Manual Transmission) or put theshift lever into "N(neutral)" position (AutomaticTransmission). Perform this operation whendriving straight.
4H 4H
4H 4H
4H








2H 2H
2H 2H
2H
Select the 2H mode switch. This can be done at
any speed, and it is not necessary to depressthe clutch pedal (Manual Transmission) or putthe shift lever into "N(neutral)" position (Auto-matic Transmission). Perform this operationwhen driving straight.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
If the transfer shift is switched into 2H mode,
If the transfer shift is switched into 2H mode, If the transfer shift is switched into 2H mode,
If the transfer shift is switched into 2H mode,
If the transfer shift is switched into 2H mode, while the vehicle is making a sharp turn or
while the vehicle is making a sharp turn or while the vehicle is making a sharp turn or
while the vehicle is making a sharp turn or
while the vehicle is making a sharp turn or
performing abrupt maneuver, the 4H indica-
performing abrupt maneuver, the 4H indica- performing abrupt maneuver, the 4H indica-
performing abrupt maneuver, the 4H indica-
performing abrupt maneuver, the 4H indica-
tor light in the instrument panel will turn off.
tor light in the instrument panel will turn off. tor light in the instrument panel will turn off.
tor light in the instrument panel will turn off.
tor light in the instrument panel will turn off.
However, the vehicle will still be in 4H mode.
However, the vehicle will still be in 4H mode. However, the vehicle will still be in 4H mode.
However, the vehicle will still be in 4H mode.
However, the vehicle will still be in 4H mode.This condition is normal.
This condition is normal. This condition is normal.
This condition is normal.
This condition is normal.
When the vehicle returns to normal driving
When the vehicle returns to normal driving When the vehicle returns to normal driving
When the vehicle returns to normal driving
When the vehicle returns to normal drivingcondition, the 4WD system will automatical-
condition, the 4WD system will automatical- condition, the 4WD system will automatical-
condition, the 4WD system will automatical-
condition, the 4WD system will automatical-
ly transfer to the 2H mode.
ly transfer to the 2H mode. ly transfer to the 2H mode.
ly transfer to the 2H mode.
ly transfer to the 2H mode.

STARTING & OPERATING
STARTING & OPERATING STARTING & OPERATING
STARTING & OPERATING
STARTING & OPERATING
3-10 o 4WD has higher ground clearance and a
narrower track to make them capable of performing in a wide variety of off roadapplications. Specific design characteristicsgive them a higher center of gravity thanordinary cars. An advantage of the higherground clearance is a better view of the roadallowing you to anticipate problems. Theyare not designed for cornering at the samespeeds as conventional 2-wheel drive vehi-cles any more than low-slung sports carsare designed to perform satisfactorily underoff-road conditions. If at all possible, avoidsharp turns or abrupt maneuvers. As withother vehicles of this type, failure to operatethis vehicle correctly may result in loss ofcontrol or vehicle rollover.
o Do not grip the inside or spokes of the steering wheel when driving off-road. Thesteering wheel could jerk and injure yourhands. Always firmly hold the outer steeringwheel when you are driving off-road.
o Drive at lower speeds in strong crosswinds. Because of your vehicle’s high center ofgravity, its stability will be affected in cross-
winds. Slower speeds ensure better vehiclecontrol.
o Whenever you drive off-road through sand, mud or water as deep as the wheel hub,more frequent maintenance may be required.
o Do not drive in water if the level is higher than the bottom of the wheel hubs. o Check your brake condition once you are
out of mud or water. Press the brake severaltimes as you move slowly until your feelnormal braking forces return.
o Four-wheel driving on flat and normal roads can result in a severe binding conditionwhen turning the steering wheel.
Driving on dry paved road and high-
Driving on dry paved road and high- Driving on dry paved road and high-
Driving on dry paved road and high-
Driving on dry paved road and high-
way
way way
way
way Select 2H(2WD) to drive on dry paved roads. Especially on dry highway, never select the 4Hor 4L(4WD).
Driving on snowy or icy roads
Driving on snowy or icy roads Driving on snowy or icy roads
Driving on snowy or icy roads
Driving on snowy or icy roads Select the 4H or 4L in accordance with the road conditions, and then gradually depress the ac-celerator pedal for a smooth start.
Driving on sandy or muddy roads
Driving on sandy or muddy roads Driving on sandy or muddy roads
Driving on sandy or muddy roads
Driving on sandy or muddy roads Select the 4H or 4L and then gradually depress the accelerator pedal for a smooth start. Keepthe pressure on the accelerator pedal constantas possible, and drive at low speed.
Climbing sharp grades
Climbing sharp grades Climbing sharp grades
Climbing sharp grades
Climbing sharp grades Select the 4L to maximize use the engine torque.
Descending sharp grades
Descending sharp grades Descending sharp grades
Descending sharp grades
Descending sharp gradesSelect 4L, use the engine brake and descend slowly.
4H 4H
4H 4H
4H






4L or 4L
4L or 4L 4L or 4L
4L or 4L
4L or 4L






4H 4H
4H 4H
4H
1. Stop the vehicle.(0-3km/h)
2. Depress the clutch pedal (Manual Trans- mission) or put the shift lever into "N(neutral)" position (Automatic Transmission).
3. Select the 4H or 4L mode switch.
2H 2H
2H 2H
2H






4L 4L
4L 4L
4L
1. Stop the vehicle.(0-3km/h)
2. Depress the clutch pedal (Manual Trans- mission) or put the shift lever into "N(neutral)"position (Automatic Transmission).
3. Select the 4L mode switch.
4L 4L
4L 4L
4L






2H 2H
2H 2H
2H
1. Stop the vehicle.(0 - 3km/h)
2. Depress the clutch pedal (Manual Trans- mission) or put the shift lever into "N(neutral)"position (Automatic Transmission).
3. Select the 2H mode switch. D090E01P-GAT
Driving Four-wheel drive safely
Driving Four-wheel drive safely Driving Four-wheel drive safely
Driving Four-wheel drive safely
Driving Four-wheel drive safely
o The driving posture should be more upright
and closer to the wheel than usual; adjust the seat to a good position for easy steeringand pedal operation.
o Be sure to wear the seat belt.
o Drive carefully when off the road and avoid dangerous areas.

6-3
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
DESCRIPTION
GENERAL MAINTENANCE ENGINE COOLANT *1 MANUAL TRANSMISSION OILAUTOMATIC TRANSMISSION OILTRANSFER CASE OIL *2REAR AXLE OILCLUTCH / BRAKE PEDAL FREE PLAY CLUTCH / BRAKE OIL RESERVOIR BRAKE HYDRAULIC FLUIDFRONT BRAKE PADSFRONT BRAKE CALIPERS / CYLINDERS / DISCREAR BRAKE DRUMS / LININGS / CYLINDERSHANDBRAKETIRE CONDITION / PRESSURE EXHAUST SYSTEM / MOUNTING STEERING JOINT / RACK / BOX OIL LEAKSSUSPENSION JOINT / SEALSFRONT WHEEL BEARINGENGINE COOLANT HOSESBRAKE PIPE CORROSION SEATBELTS / MOUNTINGS HEAD LAMPSAIR FILTER (For Evaporator and Blower unit) *3
NO.
123456 7 89
10111213 14 1516171819 20 2122
G030A04P-GAT R : REPLACE I : INSPECT AND, AFTER INSPECTION, CLEAN, ADJUST, REPAIR OR REPLACE IF NECESSARY
70 56
I I I I I I III I I 80 64
I I
R II I IIII I I IIII I90 72
I I I III I I I I I II
20 16
I I I II I IIIII I IIII I 30 24
I I I III I III I II 40 32
I I
R II I III I I IIIII I 50 40
I I I I I I III I I 60 48
I I I IIIII I I I I IIIIIII
See below
KILOMETERS X 1000 MONTHS
54
R 10
8
I I I I I I III I I
See below
*1. For every 24 months or 40,000 km, whichever occurs first : "R"
*2. For every 24 months or 48,000 km, whichever occurs first : "R"
*3. For every 12 months or 20,000 km, whichever occurs first : "R" See below

6-7
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
PREVENTIVE MAINTENANCE
DESCRIPTION
GENERAL MAINTENANCE ENGINE COOLANT *1 MANUAL TRANSMISSION OIL AUTOMATIC TRANSMISSION OIL TRANSFER CASE OIL *2 REAR AXLE OIL CLUTCH/BRAKE PEDAL FREEPLAY CLUTCH/BRAKE OIL RESERVOIR BRAKE HYDRAULIC FLUID FRONT BRAKE PAD FRONT BRAKE CALIPERS/CYLINDERS/DISC REAR BRAKE DRUMS/LININGS/CYLINDERS HAND BRAKE TIRE CONDITION/PRESSURE EXHAUST SYSTEM/MOUNTING STEERING JOINT/RACK/BOX/OIL LEAKS SUSPENSION JOINT/SEALS FRONT WHEEL BEARING ENGINE COOLANT HOSES BRAKE PIPE CORROSION
AIR FILTER (F o r Evapoerator and Blower unit) *3
NO.
12 3 4 5 6 7 8 9
1011 12 13 14 15 16 17 18 19 20KILOMETERS X 1000 MONTH90 72
I
R R I I I I I I I I I I I I I I
G060A04P-GAT R : REPLACE I : INSPECT AND, AFTER INSPECTION, CLEAN, ADJUST, REPAIR OR REPLACE IF NECESSARY15 12
II I I I I I I I 30 24
II I I I I I I I I I I I I I I I 4536
II
R II I I I I 60 48
II I I I I I I I I I I I I I I I 7560
II I I I I I I I7.5 6
R
See below See below
*1. For every 24 months or 45,000 km, whichever occurs first : "R" *2. For every 24 months or 48,000 km, whichever occurs first : "R"*3. For every 12 months or 20,000 km, whichever occurs first : "R"
See below

CONSUMER INFORMATION
CONSUMER INFORMATION CONSUMER INFORMATION
CONSUMER INFORMATION
CONSUMER INFORMATION
8-6 I040A01P-GAT
Vehicle Interior
Vehicle Interior Vehicle Interior
Vehicle Interior
Vehicle Interior
The following should be checked each time when the vehicle is driven:
o Light operation
o Windshield wiper operation
o Horn operation
o Defroster, heater operation (and air condi- tioning, if equipped)
o Steering operation and condition
o Mirror condition and operation
o Turn signal operation
o Accelerator pedal operation
o Brake operation, including parking brake
o Manual transmission operation, including clutch operation
o Automatic transmission operation, including "Park" mechanism operation
o Seat control condition and operation
o Seat belt condition and operation
o Sunvisor operation
If you notice anything that does not operate correctly or appear to be functioning correctly,inspect it carefully and seek assistance fromyour Hyundai dealer if service is needed. Adequate care of your vehicle at regular inter- vals serves to preserve the value and appear-ance as long as possible. Some maintenance items can be carried out bythe owner (Consumer Information), while othershould be done only by an authorized dealer(Periodic Inspection and Maintenance). Thissection describes only those items which canbe carried out by the owner. In the event amalfunction or other problem is discovered,have it corrected by an authorized HYUNDAIdealer. This section contains information oninspection maintenance procedures that youcan do yourself, if you so desire. Follow theinstructions and cautions for each of the vari-ous procedures. When checking or servicing the inside of the engine compartment, be sure the engine isstopped and has had a chance to cool down. Ifit is necessary to do work in the engine com-partment with the engine running, be especiallycareful that your clothing, hair, etc., becomesnot caught by the fan, V-belts, or other movingparts. I050A01P-GAT
Inspection items
Inspection items Inspection items
Inspection items
Inspection items
( 1 ) Engine oil
( 2 ) Engine coolant
(3) Battery
( 4 ) Brake fluid
( 5 ) Clutch fluid (hydraulic clutch only)
( 6 ) Washer fluid
( 7 ) Wheel condition (including spare wheel)
(8) Tire inflation pressure (including spare
wheel)
I020A02P-GAT
GENERAL CHECKS
GENERAL CHECKS GENERAL CHECKS
GENERAL CHECKS
GENERAL CHECKS
Engine Compartment
Engine Compartment Engine Compartment
Engine Compartment
Engine Compartment The following should be checked regularly:
o Engine oil level and condition
o Transmission fluid level and condition
o Brake fluid level
o Clutch fluid level
o Engine coolant level
o Windshield washer fluid level
o Accessory drive belt condition
o Coolant hose condition
o Fluid leaks (on or below components)
o Power steering fluid level and condition
o Tire pressure and condition (including spare)
o Battery condition I030A02P-GAT
Vehicle Exterior
Vehicle Exterior Vehicle Exterior
Vehicle Exterior
Vehicle Exterior The following should be checked monthly:
o Overall appearance and condition
o Wheel condition and wheel nut tightness
o Air cleaner filter condition
o Exhaust system condition
o Light condition and operation
o Windshield glass condition
o Wiper blade condition
o Paint condition and corrosion
o Fluid leaks
o Door and hood lock condition

8-7
CONSUMER INFORMATION
CONSUMER INFORMATION CONSUMER INFORMATION
CONSUMER INFORMATION
CONSUMER INFORMATION
( 9 ) Fuel, engine coolant, oil and exhaust gas leakage
(10) Exterior and interior lamp operation (11) Meter, gauge, and indication/warning lamp operation
(12) Steering wheel free play(13) Clutch pedal free play (14) Brake pedal free play (15) Parking brake lever stroke
Others
Others Others
Others
Others
(1) Wheel rotation
(1) Wheel rotation (1) Wheel rotation
(1) Wheel rotation
(1) Wheel rotation
Every 20,000km (12,000miles)or 12
Every 20,000km (12,000miles)or 12 Every 20,000km (12,000miles)or 12
Every 20,000km (12,000miles)or 12
Every 20,000km (12,000miles)or 12
months, whichever comes first
months, whichever comes first months, whichever comes first
months, whichever comes first
months, whichever comes first
(2) Hinge and latch lubrication
(2) Hinge and latch lubrication (2) Hinge and latch lubrication
(2) Hinge and latch lubrication
(2) Hinge and latch lubrication level surface, stop the engine, and then wait a few moments to allow the engine oil in circula-tion to return to the oil pan to ensure accuratemeasurement. Remove the dipstick and wipe itwith a clean cloth. Reinsert the dipstick andread the oil level, which should always bewithin the range indicated in the figure.
GS80030A
Good
I060A01P-GAT
ENGINE OIL
ENGINE OIL ENGINE OIL
ENGINE OIL
ENGINE OIL
It is important to check the oil level at regular
intervals or before starting a long trip.
This check must be made with the engine
warm but not running. Park the vehicle on a
GS80040A
If the oil level is below the specified limit,
remove the cap located on the cylinder head cover and add enough oil to raise the level towithin the specified range. Be sure to use thespecified engine oil and do not mix varioustypes of oil. Also, avoid mixing different makesof oil together if possible. After adding oil, closethe cap securely.
WARNING:
WARNING: WARNING:
WARNING:
WARNING:
Be careful not to touch the hot exhaust
Be careful not to touch the hot exhaust Be careful not to touch the hot exhaust
Be careful not to touch the hot exhaust
Be careful not to touch the hot exhaust manifold.
manifold. manifold.
manifold.
manifold. CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Avoid overfilling, or the engine could be
Avoid overfilling, or the engine could be Avoid overfilling, or the engine could be
Avoid overfilling, or the engine could be
Avoid overfilling, or the engine could bedamaged.
damaged. damaged.
damaged.
damaged.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
Check the oil level on the dipstick once
Check the oil level on the dipstick once Check the oil level on the dipstick once
Check the oil level on the dipstick once
Check the oil level on the dipstick onceagain after adding the oil.
again after adding the oil. again after adding the oil.
again after adding the oil.
again after adding the oil.
I070A05P-GATSelection of engine oil
Selection of engine oil Selection of engine oil
Selection of engine oil
Selection of engine oil (1) Use engine oil conforming to the following
API classification. Gasoline Engine
Europe : SG, SG/CD, SH or SH/CDExcept Europe : SE or above
Diesel Engine 2.6 N/A : CF-4 or above2.5 4D56 T/C or TCI : CF-4 or above
2.5 CRDi TCI : CE or above
(2) Select engine oil of the proper SAE viscos- ity number according to the atmospheric temperature. Recommened viscosity is given in the fol- lowing drawing.