2003 Hyundai H-1 (Grand Starex) engine oil

1-1
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
B000A01P-GAT 1.1.
1.1.
1.
BEFORE DRIVING
BEFORE DRIVING BEFORE DRIVING
BEFORE DRIVING
BEFORE DRIVING
YY
YY
Y
OUR
OUR OUR
OUR
OUR VEHICLE
VEHICLE VEHICLE
VEHICLE
VEHICLE
B010B01P-GAT Before entering the vehicle
Before entering the vehicle Before entering the vehicle
Before entering the vehicle
Before entering the vehicle
o Check that windows, mirrors and lights are clean.
o Check if any tire is low or flat.
o Look for fluid leaks.
o Check that area is clear if you’re about to back up.
B010C03P-GAT After entering the vehicle
After entering the vehicle After entering the vehicle
After entering the vehicle
After entering the vehicle
o Lock all doors.
o The driver and passengers are wearing prop- erly adjusted seat belts.
o The head restraints are properly adjusted, if so equipped.
o Adjust inside and outside mirrors.
o Check warning lights for correct operation, with the ignition key in the position "ON".
o Check all gauges, for normal operation.
B010A01P-GAT
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
BEFORE DRIVING YOUR VEHICLE
SAFETY CHECKS
SAFETY CHECKS SAFETY CHECKS
SAFETY CHECKS
SAFETY CHECKS
Be sure you know your vehicle and its equip-
ment and how to use it safely.
B020A01P-GATRUNNING-IN RECOMMENDATIONS
RUNNING-IN RECOMMENDATIONS RUNNING-IN RECOMMENDATIONS
RUNNING-IN RECOMMENDATIONS
RUNNING-IN RECOMMENDATIONS During the running-in period for the first
1,000km(600miles), it is advisable to drive your new vehicle using the following precautions asa guideline to aid long life as well as futureeconomy and performance.
1. Do not race the engine at high speeds.
2. Avoid rapid starting, acceleration, braking and prolonged high-speed running.
3. Keep to the running-in speed limit shown below. B030A01P-GAT
BEFORE OPERATION
BEFORE OPERATION BEFORE OPERATION
BEFORE OPERATION
BEFORE OPERATION
PRECAUTIONS FOR NEW VEHICLE
PRECAUTIONS FOR NEW VEHICLE PRECAUTIONS FOR NEW VEHICLE
PRECAUTIONS FOR NEW VEHICLE
PRECAUTIONS FOR NEW VEHICLE The performance and life of a vehicle depend
largely on how the vehicle is handled when new.
To maintain the parts smoothly and sustain
high performance for a long time to come, besure to observe the following points.
Make sure that your vehicle does not miss
Make sure that your vehicle does not miss Make sure that your vehicle does not miss
Make sure that your vehicle does not miss
Make sure that your vehicle does not miss the first 5,000 km inspections.
the first 5,000 km inspections. the first 5,000 km inspections.
the first 5,000 km inspections.
the first 5,000 km inspections.
After the first 5,000 km of driving, take your vehicle
to your nearest service shop for inspection.
Drive range
1st
2nd 3rd4th 5thRunning-in speed
0~25(0~16)
20~50(13~31) 30~80(19~50)
40~(25~)50~(32~) km/h (mph)
WARNING: (Diesel only)
WARNING: (Diesel only) WARNING: (Diesel only)
WARNING: (Diesel only)
WARNING: (Diesel only)
To ensure that sufficient vacuum exists with-
To ensure that sufficient vacuum exists with- To ensure that sufficient vacuum exists with-
To ensure that sufficient vacuum exists with-
To ensure that sufficient vacuum exists with-in the brake system during cold weather
in the brake system during cold weather in the brake system during cold weather
in the brake system during cold weather
in the brake system during cold weather
start-up conditions, it is necessary to run
start-up conditions, it is necessary to run start-up conditions, it is necessary to run
start-up conditions, it is necessary to run
start-up conditions, it is necessary to run
the engine at idle after starting the engine.
the engine at idle after starting the engine. the engine at idle after starting the engine.
the engine at idle after starting the engine.
the engine at idle after starting the engine.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
Fluid levels, such as engine oil, engine cool-
Fluid levels, such as engine oil, engine cool- Fluid levels, such as engine oil, engine cool-
Fluid levels, such as engine oil, engine cool-
Fluid levels, such as engine oil, engine cool-ant, brake fluid, and windshield washer flu-
ant, brake fluid, and windshield washer flu- ant, brake fluid, and windshield washer flu-
ant, brake fluid, and windshield washer flu-
ant, brake fluid, and windshield washer flu-
id, should be checked daily and/or weekly,
id, should be checked daily and/or weekly, id, should be checked daily and/or weekly,
id, should be checked daily and/or weekly,
id, should be checked daily and/or weekly,
or whenever you refuel.
or whenever you refuel. or whenever you refuel.
or whenever you refuel.
or whenever you refuel.
Further details are described in the "CON-
Further details are described in the "CON- Further details are described in the "CON-
Further details are described in the "CON-
Further details are described in the "CON-SUMER INFORMATION" section.
SUMER INFORMATION" section. SUMER INFORMATION" section.
SUMER INFORMATION" section.
SUMER INFORMATION" section.
11
11
1
Please note that the legal speed limits dis-
played must be adhered to.
4. Do not exceed loading limits.
5. Refrain from towing a trailer.

2-9
INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
C130B01P-GAT DOOR-AJAR WARNING
DOOR-AJAR WARNING DOOR-AJAR WARNING
DOOR-AJAR WARNING
DOOR-AJAR WARNING
LAMP-RED
LAMP-RED LAMP-RED
LAMP-RED
LAMP-RED
This lamp illuminates and the warning chime
will sound at the same time when a door is opened or incompletely closed.
C130F01P-GAT TURN-SIGNAL INDICATION
TURN-SIGNAL INDICATION TURN-SIGNAL INDICATION
TURN-SIGNAL INDICATION
TURN-SIGNAL INDICATION
LAMPS-GREEN
LAMPS-GREEN LAMPS-GREEN
LAMPS-GREEN
LAMPS-GREEN
These indication lamps blink on and off when a
turn-signal lamp is blinking. If the blinking is too short, the cause may be a faulty turn-signallamp connection or a blown lamp bulb.
C130G01P-GAT HIGH-BEAM INDICATION
HIGH-BEAM INDICATION HIGH-BEAM INDICATION
HIGH-BEAM INDICATION
HIGH-BEAM INDICATION
LAMP-BLUE
LAMP-BLUE LAMP-BLUE
LAMP-BLUE
LAMP-BLUE
This indication lamp illuminates when the high
beams are on.
C130H01P-GAT FUEL FILTER WARNING
FUEL FILTER WARNING FUEL FILTER WARNING
FUEL FILTER WARNING
FUEL FILTER WARNING
LAMP-RED
LAMP-RED LAMP-RED
LAMP-RED
LAMP-RED
This lamp illuminates when the ignition switch
is set to the "ON" position and goes off after the engine has started. If it lights up while theengine is running, it indicates that water hasaccumulated inside the fuel filter. If this hap-pens, remove the water from the fuel filter.
(Refer to "In case of emergency")
C130I01P-GAT OVERDRIVE/OFF
OVERDRIVE/OFF OVERDRIVE/OFF
OVERDRIVE/OFF
OVERDRIVE/OFF
INDICATOR (If installed)
INDICATOR (If installed) INDICATOR (If installed)
INDICATOR (If installed)
INDICATOR (If installed)
When the overdrive switch is turned on and 4th
gear is engaged, the overdrive off indicator will go out. This amber indicator will be illuminatedwhen the overdrive switch is turned off.
C130J01P-GAT BRAKE WARNING AND
BRAKE WARNING AND BRAKE WARNING AND
BRAKE WARNING AND
BRAKE WARNING AND
PARKING BRAKE INDICATION
PARKING BRAKE INDICATION PARKING BRAKE INDICATION
PARKING BRAKE INDICATION
PARKING BRAKE INDICATION
LAMP-RED
LAMP-RED LAMP-RED
LAMP-RED
LAMP-RED
With the ignition switch at the "ON" position,
the brake warning lamp illuminates under the following conditions:
1. When the brake fluid level in the reservoir falls to a low level.
2. If a malfunction develops in the brake servo system.
If the lamp illuminates, stop the vehicle immedi-
ately and call the nearest authorized HYUNDAI dealer.
C130C01P-GAT
OIL PRESSURE WARNING
OIL PRESSURE WARNING OIL PRESSURE WARNING
OIL PRESSURE WARNING
OIL PRESSURE WARNING
LAMP-RED
LAMP-RED LAMP-RED
LAMP-RED
LAMP-RED
This lamp illuminates when the ignition switch
is set to the "ON" position and goes off after theengine has started. If it lights up while theengine is running, the engine must be stoppedat once. Contact the nearest authorizedHYUNDAI dealer.
C130D01P-GAT LOW FUEL WARNING
LOW FUEL WARNING LOW FUEL WARNING
LOW FUEL WARNING
LOW FUEL WARNING
LAMP-AMBER
LAMP-AMBER LAMP-AMBER
LAMP-AMBER
LAMP-AMBER
This lamp illuminates when the fuel level in the
fuel tank falls to a low level. If it illuminates, the fuel should be added soon.
C130E01P-GAT CHARGE WARNING
CHARGE WARNING CHARGE WARNING
CHARGE WARNING
CHARGE WARNING
LAMP-RED
LAMP-RED LAMP-RED
LAMP-RED
LAMP-RED
This lamp illuminates when the ignition switch
is set to the "ON" position and goes off after the engine has started. If it lights up while theengine is running, there is a problem in thecharging system. Check to see if the V-belt isbroken, and then contact the nearest autho-rized HYUNDAI dealer.
C130L01P-GAT
DIESEL PREHEAT
DIESEL PREHEAT DIESEL PREHEAT
DIESEL PREHEAT
DIESEL PREHEAT
INDICATION LIGHT-AMBER
INDICATION LIGHT-AMBER INDICATION LIGHT-AMBER
INDICATION LIGHT-AMBER
INDICATION LIGHT-AMBER
The indication light illuminates amber when the
ignition switch is placed at the "ON" position. The engine can be started after the preheatindication light goes off. The illuminating timevaries with the water temperature.
Water temperature
(°C)
Below -30 -20
0
20 40 Illuminating time
(sec)
151032 1

INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
2-10 C130P01P-GAT
A/T (AUTOMATIC TRANSMIS-
A/T (AUTOMATIC TRANSMIS- A/T (AUTOMATIC TRANSMIS-
A/T (AUTOMATIC TRANSMIS-
A/T (AUTOMATIC TRANSMIS-
SION) OIL TEMPERATURE
SION) OIL TEMPERATURE SION) OIL TEMPERATURE
SION) OIL TEMPERATURE
SION) OIL TEMPERATURE
WARNING LIGHT
WARNING LIGHT WARNING LIGHT
WARNING LIGHT
WARNING LIGHT
(If installed)
(If installed) (If installed)
(If installed)
(If installed)
The A/T oil temperature warning light comes on when the automatic transmission oil tempera-ture goes up to the temperature that may resultin serious damage of automatic transmission. If the A/T oil temperature warning light comes on while driving, park your vehicle in at a safeplace as soon as possible and with the selectorlever is shifted into "P" position, and allow theengine to idle until the warning light goes off.And when the warning light goes off, the vehiclecan be driven normally. If the warning light doesn't go off or it lights up frequently, have the vehicle checked by yourHyundai dealer.
A/TA/T
A/TA/T
A/T
TEMPTEMP
TEMPTEMP
TEMP
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
If the engine were not started within 10
If the engine were not started within 10 If the engine were not started within 10
If the engine were not started within 10
If the engine were not started within 10 seconds after the preheating is completed,
seconds after the preheating is completed, seconds after the preheating is completed,
seconds after the preheating is completed,
seconds after the preheating is completed,
turn the ignition key once more to the
turn the ignition key once more to the turn the ignition key once more to the
turn the ignition key once more to the
turn the ignition key once more to the
"LOCK" position, and then to the "ON" po-
"LOCK" position, and then to the "ON" po- "LOCK" position, and then to the "ON" po-
"LOCK" position, and then to the "ON" po-
"LOCK" position, and then to the "ON" po-
sition, in order to preheat again.
sition, in order to preheat again. sition, in order to preheat again.
sition, in order to preheat again.
sition, in order to preheat again. B260E02A-GAT
SEAT BELT REMINDER LIGHT
SEAT BELT REMINDER LIGHT SEAT BELT REMINDER LIGHT
SEAT BELT REMINDER LIGHT
SEAT BELT REMINDER LIGHT
(If installed)
(If installed) (If installed)
(If installed)
(If installed)
The seat belt reminder light comes on until your seat belt is fastened when the ignition key isturned from the "OFF" position to "ON" or"START". C130O01P-GAT
ENGINE WARNING LIGHT
ENGINE WARNING LIGHT ENGINE WARNING LIGHT
ENGINE WARNING LIGHT
ENGINE WARNING LIGHT
(If installed)
(If installed) (If installed)
(If installed)
(If installed)
This light illuminates when there is a malfunc-
tion of an exhaust gas related component, andthe system is not functioning properly so thatthe exhaust gas regulation values are not satis-fied. This light will also illuminate when theignition key is turned to the "ON" position, andthen it will go out in a few seconds. If it illumi-nates while driving, or does not illuminate whenthe ignition key is turned to the "ON" position,take your car to your nearest authorized Hyundaidealer and have the system checked.
B260B01S-GAT SRS (AIRBAG) SERVICE
SRS (AIRBAG) SERVICE SRS (AIRBAG) SERVICE
SRS (AIRBAG) SERVICE
SRS (AIRBAG) SERVICE
REMINDER INDICATOR
REMINDER INDICATOR REMINDER INDICATOR
REMINDER INDICATOR
REMINDER INDICATOR (SRI)
(SRI) (SRI)
(SRI)
(SRI)
(If installed)
(If installed) (If installed)
(If installed)
(If installed)
The SRS service reminder indicator (SRI)
comes on and flashes for about 6 secondsafter the ignition key is turned to the "ON"
position or after the engine is started, afterwhich it will go out.
This light also comes on when the SRS is not
working properly. If the SRI does not come on,or continuously remains on after flashing forabout 6 seconds when you turned the ignition
key to the "ON" position or started the engine,or if it comes on while driving, have the SRSinspected by an authorized Hyundai Dealer.
C130N01P-GAT
ANTI-LOCK BRAKE WARNING
ANTI-LOCK BRAKE WARNING ANTI-LOCK BRAKE WARNING
ANTI-LOCK BRAKE WARNING
ANTI-LOCK BRAKE WARNING
LIGHT (If installed)
LIGHT (If installed) LIGHT (If installed)
LIGHT (If installed)
LIGHT (If installed)
When the key is turned to the "ON" position, the
ABS light will come on and then go off in a fewseconds. If the ABS light remains on, comes on while
driving, or does not come on when the key isturned to the "ON" position, this indicates thatthere may be a problem with the ABS.
If this occurs, have your vehicle checked by
your Hyundai dealer as soon as possible. Thenormal braking system will still be operational,but without the assistance of the anti-lock brakesystem.
AIRAIR
AIRAIR
AIR
BAGBAG
BAGBAG
BAG
B270B02O-GATPARKING START WARNING SOUND
PARKING START WARNING SOUND PARKING START WARNING SOUND
PARKING START WARNING SOUND
PARKING START WARNING SOUND
(If installed)
(If installed) (If installed)
(If installed)
(If installed)
If the vehicle driven at over 10km/h(6mph) more 2~3 seconds, the warning chime will soundcontinuously when the parking brake engaged.

2-15
INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
INSTRUMENTS & CONTROLS
B620A01S-AATFRONT DOOR EDGE WARNING LIGHT
FRONT DOOR EDGE WARNING LIGHT FRONT DOOR EDGE WARNING LIGHT
FRONT DOOR EDGE WARNING LIGHT
FRONT DOOR EDGE WARNING LIGHT
(If installed)
(If installed) (If installed)
(If installed)
(If installed)
C230A01P-GAT
ENGINE RPM ADJUSTMENT KNOB
ENGINE RPM ADJUSTMENT KNOB ENGINE RPM ADJUSTMENT KNOB
ENGINE RPM ADJUSTMENT KNOB
ENGINE RPM ADJUSTMENT KNOB
(D(D
(D(D
(D iesel)
iesel) iesel)
iesel)
iesel)
C230A01P-1
When the outside air temperature is very low, or when it is necessary to warm up the engine,then turn the knob clockwise to that point atwhich the engine runs smoothly, and then,once the warming up is completed, fully turnthe knob counter-clockwise.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Never attempt to adjust the vehicle during
Never attempt to adjust the vehicle during Never attempt to adjust the vehicle during
Never attempt to adjust the vehicle during
Never attempt to adjust the vehicle during
driving by using the control knob.
driving by using the control knob. driving by using the control knob.
driving by using the control knob.
driving by using the control knob.B620A01S-AAG
A red light comes on when the front door is
opened. The purpose of this light is to assist when you get in or out and also to warn passing
vehicles. B550A01Y-AAT
HIGH-MOUNTED REAR STOP LIGHT
HIGH-MOUNTED REAR STOP LIGHT HIGH-MOUNTED REAR STOP LIGHT
HIGH-MOUNTED REAR STOP LIGHT
HIGH-MOUNTED REAR STOP LIGHT
(Minibus, Van) (If Installed)
(Minibus, Van) (If Installed) (Minibus, Van) (If Installed)
(Minibus, Van) (If Installed)
(Minibus, Van) (If Installed)B550A01P
In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rearstoplight in the center of the rear window orinstalled in the rear spoiler also comes on whenthe brakes are applied.

3-3
STARTING & OPERATING
STARTING & OPERATING STARTING & OPERATING
STARTING & OPERATING
STARTING & OPERATING
GT30060A
4. Operate the accelerator pedal as described
below in accordance with the atmospheric temperature and/or engine condition.
(1) When the atmospheric temperature is moderate or the engine is warm: Start the engine without depressing the accelerator pedal.
(2) When the atmospheric temperature is low and the engine is cold: Start the engine while depressing the accelerator pedal. If the atmospherictemperature is very low, setting the igni-tion switch to ON for one or two sec-onds before attempting to start the en-gine will make it easier to start.
5. Start the engine D041A02P-GAT
STARTING AND STOPPING THE EN-
STARTING AND STOPPING THE EN- STARTING AND STOPPING THE EN-
STARTING AND STOPPING THE EN-
STARTING AND STOPPING THE EN-
GINE FOR TURBO CHARGER OR
GINE FOR TURBO CHARGER OR GINE FOR TURBO CHARGER OR
GINE FOR TURBO CHARGER OR
GINE FOR TURBO CHARGER OR
TURBO CHARGER INTERCOOLER
TURBO CHARGER INTERCOOLER TURBO CHARGER INTERCOOLER
TURBO CHARGER INTERCOOLER
TURBO CHARGER INTERCOOLER
(If installed)
(If installed) (If installed)
(If installed)
(If installed)
(1) Do not race the engine or sudden accelerate the engine immediately after start it. If theengine is cold, allow the engine to idle forseveral seconds before it is driven to ensuresufficient lubrication of the turbo chargerunit.
(2) After high speed or extended driving, requir- ing a heavy engine load, the engine shouldbe allowed to idle, as shown in the chartbelow, before turning it off. This idle time will allow the turbo charger to cool prior to shutting the engine off.
Required Idle Time
Required Idle Time Required Idle Time
Required Idle Time
Required Idle Time
High speed driving Driving Condition
Driving Condition Driving Condition
Driving Condition
Driving Condition
Normal drivingNot necessary About 20 seconds About 1 minute
Up to 100km/h
Up to 80 km/h
Steep mountain slopes or contin- ued driving in excess of 100km/h About 2 minutes
WARNING:
WARNING: WARNING:
WARNING:
WARNING:
Do not turn the engine off immediately after
Do not turn the engine off immediately after Do not turn the engine off immediately after
Do not turn the engine off immediately after
Do not turn the engine off immediately after
it has been subjected to a heavy load. Doing
it has been subjected to a heavy load. Doing it has been subjected to a heavy load. Doing
it has been subjected to a heavy load. Doing
it has been subjected to a heavy load. Doing
so may cause severe damage to the engine
so may cause severe damage to the engine so may cause severe damage to the engine
so may cause severe damage to the engine
so may cause severe damage to the engine
or turbo charger unit.
or turbo charger unit. or turbo charger unit.
or turbo charger unit.
or turbo charger unit.
D040A01P-GAT
Tips for starting
Tips for starting Tips for starting
Tips for starting
Tips for starting
(1) Do not operate the starter motor continu-
ously for longer than ten seconds; doing so could run down the battery. If the enginedoes not start, turn the ignition switch backto "LOCK", wait a few minutes, and then tryagain.
(2) If the engine cannot be started because the battery is weak or dead, refer to the emer-gency starting section for instructions onEmergency Starting.
(3) After starting the engine, do not keep the engine idling without driving. Once when the atmospheric temperature is very low, warm up the engine at a high idlingspeed to ensure proper circulation of the oil.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
(1)(1)
(1)(1)
(1) Do not run the engine at high rpm or
Do not run the engine at high rpm or Do not run the engine at high rpm or
Do not run the engine at high rpm or
Do not run the engine at high rpm or
drive the vehicle at high speed until the
drive the vehicle at high speed until the drive the vehicle at high speed until the
drive the vehicle at high speed until the
drive the vehicle at high speed until the
engine has had a chance to warm up.
engine has had a chance to warm up. engine has had a chance to warm up.
engine has had a chance to warm up.
engine has had a chance to warm up.
(2)(2)
(2)(2)
(2) Release the ignition key as soon as the
Release the ignition key as soon as the Release the ignition key as soon as the
Release the ignition key as soon as the
Release the ignition key as soon as the
engine starts to avoid damaging the
engine starts to avoid damaging the engine starts to avoid damaging the
engine starts to avoid damaging the
engine starts to avoid damaging the
starter motor.
starter motor. starter motor.
starter motor.
starter motor.

3-9
STARTING & OPERATING
STARTING & OPERATING STARTING & OPERATING
STARTING & OPERATING
STARTING & OPERATING
D090A01P-GAG
D090A01P-GAT
FOUR-WHEEL DRIVE (4WD)
FOUR-WHEEL DRIVE (4WD) FOUR-WHEEL DRIVE (4WD)
FOUR-WHEEL DRIVE (4WD)
FOUR-WHEEL DRIVE (4WD)
(Minibus, Van) (If installed)
(Minibus, Van) (If installed) (Minibus, Van) (If installed)
(Minibus, Van) (If installed)
(Minibus, Van) (If installed) You can send your engine power to all front and rear wheels for maximum power. 4WD is usefulwhen you drive in snow, mud, ice, mountainousor sandy areas where good traction is required,or when your wheels lose traction using two-wheel drive.
Switch position
Switch position Switch position
Switch position
Switch position
2H(Rear-wheel drive)
2H(Rear-wheel drive) 2H(Rear-wheel drive)
2H(Rear-wheel drive)
2H(Rear-wheel drive) When driving on normal roads and highway. 4H(High range 4-wheel drive)
4H(High range 4-wheel drive) 4H(High range 4-wheel drive)
4H(High range 4-wheel drive)
4H(High range 4-wheel drive)
When driving deep snow, sand or rough roads
with normal speed. The 4WD indication light(HI) will be turned on to remind you that you are inthe 4H mode.
4L(Low range 4-wheel drive)
4L(Low range 4-wheel drive) 4L(Low range 4-wheel drive)
4L(Low range 4-wheel drive)
4L(Low range 4-wheel drive)
When driving up or descending steep slopes or
rough roads such as muddy road. Especiallywhen increased drive power is required.
The indication light(LO) will be turned on to
remind you that you are in the 4L mode.
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
Do not select 4WD mode on dry paved roads.
Do not select 4WD mode on dry paved roads. Do not select 4WD mode on dry paved roads.
Do not select 4WD mode on dry paved roads.
Do not select 4WD mode on dry paved roads. Especially on dry high way, never select the
Especially on dry high way, never select the Especially on dry high way, never select the
Especially on dry high way, never select the
Especially on dry high way, never select the
4WD(4H or 4L).
4WD(4H or 4L). 4WD(4H or 4L).
4WD(4H or 4L).
4WD(4H or 4L).
Four-wheel driving on dry paved roads for a
Four-wheel driving on dry paved roads for a Four-wheel driving on dry paved roads for a
Four-wheel driving on dry paved roads for a
Four-wheel driving on dry paved roads for along period will increase the fuel consump-
long period will increase the fuel consump- long period will increase the fuel consump-
long period will increase the fuel consump-
long period will increase the fuel consump-
tion with possible noise generation and ear-
tion with possible noise generation and ear- tion with possible noise generation and ear-
tion with possible noise generation and ear-
tion with possible noise generation and ear-
ly tire wear. In addition, differential oil tem-
ly tire wear. In addition, differential oil tem- ly tire wear. In addition, differential oil tem-
ly tire wear. In addition, differential oil tem-
ly tire wear. In addition, differential oil tem-
perature increases with possible driving
perature increases with possible driving perature increases with possible driving
perature increases with possible driving
perature increases with possible driving
system part wear.
system part wear. system part wear.
system part wear.
system part wear.
D090D02P-GAT
Transfer shift switch operation
Transfer shift switch operation Transfer shift switch operation
Transfer shift switch operation
Transfer shift switch operation
By selecting the transfer shift switch(4H, 4L),
the both axles of the vehicle are rigidly connect- ed with each other. This improves the tractioncharacteristics.
2H 2H
2H 2H
2H








4H 4H
4H 4H
4H
Select the 4H mode switch at speed below
60~70 km/h. It is not necessary to depress theclutch pedal (Manual Transmission) or put theshift lever into "N(neutral)" position (AutomaticTransmission). Perform this operation whendriving straight.
4H 4H
4H 4H
4H








2H 2H
2H 2H
2H
Select the 2H mode switch. This can be done at
any speed, and it is not necessary to depressthe clutch pedal (Manual Transmission) or putthe shift lever into "N(neutral)" position (Auto-matic Transmission). Perform this operationwhen driving straight.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
If the transfer shift is switched into 2H mode,
If the transfer shift is switched into 2H mode, If the transfer shift is switched into 2H mode,
If the transfer shift is switched into 2H mode,
If the transfer shift is switched into 2H mode, while the vehicle is making a sharp turn or
while the vehicle is making a sharp turn or while the vehicle is making a sharp turn or
while the vehicle is making a sharp turn or
while the vehicle is making a sharp turn or
performing abrupt maneuver, the 4H indica-
performing abrupt maneuver, the 4H indica- performing abrupt maneuver, the 4H indica-
performing abrupt maneuver, the 4H indica-
performing abrupt maneuver, the 4H indica-
tor light in the instrument panel will turn off.
tor light in the instrument panel will turn off. tor light in the instrument panel will turn off.
tor light in the instrument panel will turn off.
tor light in the instrument panel will turn off.
However, the vehicle will still be in 4H mode.
However, the vehicle will still be in 4H mode. However, the vehicle will still be in 4H mode.
However, the vehicle will still be in 4H mode.
However, the vehicle will still be in 4H mode.This condition is normal.
This condition is normal. This condition is normal.
This condition is normal.
This condition is normal.
When the vehicle returns to normal driving
When the vehicle returns to normal driving When the vehicle returns to normal driving
When the vehicle returns to normal driving
When the vehicle returns to normal drivingcondition, the 4WD system will automatical-
condition, the 4WD system will automatical- condition, the 4WD system will automatical-
condition, the 4WD system will automatical-
condition, the 4WD system will automatical-
ly transfer to the 2H mode.
ly transfer to the 2H mode. ly transfer to the 2H mode.
ly transfer to the 2H mode.
ly transfer to the 2H mode.

STARTING & OPERATING
STARTING & OPERATING STARTING & OPERATING
STARTING & OPERATING
STARTING & OPERATING
3-16 D180H01P-GAT
Parking brake
Parking brake Parking brake
Parking brake
Parking brake
If the atmospheric temperature is below freez- ing, park the vehicle with the gearshift lever in1st or reverse and do not engage the parkingbrake. If the parking brake is engaged and thereis moisture on the brake linings, the liningscould become frozen to the brake drums, mak-ing it impossible to release the parking brake.
C160G02A-AAT
To Keep Locks from Freezing
To Keep Locks from Freezing To Keep Locks from Freezing
To Keep Locks from Freezing
To Keep Locks from Freezing
To keep the locks from freezing, squirt anapproved de-icer fluid or glycerine into the keyopening. If a lock is covered with ice, squirt itwith an approved de-icing fluid to remove theice. If the lock is frozen internally, you may beable to thaw it out by using a heated key.Handle the heated key with care to avoid burn-ing your fingers.
NOTE:
NOTE: NOTE:
NOTE:
NOTE:
The proper temperature for using the immo-
The proper temperature for using the immo- The proper temperature for using the immo-
The proper temperature for using the immo-
The proper temperature for using the immo-
bilizer key is from -40°C to 80°C. If you heat
bilizer key is from -40°C to 80°C. If you heat bilizer key is from -40°C to 80°C. If you heat
bilizer key is from -40°C to 80°C. If you heat
bilizer key is from -40°C to 80°C. If you heat
the immobilizer key over 80°C to open the
the immobilizer key over 80°C to open the the immobilizer key over 80°C to open the
the immobilizer key over 80°C to open the
the immobilizer key over 80°C to open the
frozen lock, it may cause damage to the
frozen lock, it may cause damage to the frozen lock, it may cause damage to the
frozen lock, it may cause damage to the
frozen lock, it may cause damage to the
transponder in its head.
transponder in its head. transponder in its head.
transponder in its head.
transponder in its head. D180G01P-GAT
Door locks
Door locks Door locks
Door locks
Door locks
To prevent the door locks from freezing up, the lock cylinders should be masked with tape,etc., when washing the vehicle in cold weatherto prevent the entrance of water.
D180E01P-GAT
Wiper blades
Wiper blades Wiper blades
Wiper blades
Wiper blades
Before operating the wipers, check the wiperblades to confirm that they are not frozen to thewindshield or tailgate. If the blades are frozen tothe windshield or tailgate, do not operate thewipers until the ice has melted and the bladesare freed. D180F01P-GAT
Ventilation slots
Ventilation slots Ventilation slots
Ventilation slots
Ventilation slots
The ventilation slots in the headlight housing on the assistant seat side should be brushed clearafter a heavy snowfall so that the operation ofthe heating and ventilation systems will not beimpaired.
anyway, will only deliver a fraction of the startercurrent which is normally available. It is recommended that you have the battery checked by an authorized HYUNDAI dealerbefore the start of cold weather and, if neces-sary, have it charged. This not only ensures reliable starting, but a battery which is kept fully charged also has alonger life. D180D01P-GAT
Washer fluid
Washer fluid Washer fluid
Washer fluid
Washer fluid
To ensure proper operation of the windshield or rear window at low temperatures, anti-freezeshould be added to the washer fluid at a rate ofone part antifreeze to one part water.
D180A01P-GAT
DURING COLD WEATHER
DURING COLD WEATHER DURING COLD WEATHER
DURING COLD WEATHER
DURING COLD WEATHER
Engine oil
Engine oil Engine oil
Engine oil
Engine oil
The engine oil can become very thick at low
temperatures, thus making it difficult to start theengine.
Change to a thinner oil designed for winter use
before the start of cold weather; for the appro-priate oil viscosity, refer to the "Consumer Infor-mation" section.
D180B01P-GATEngine coolant
Engine coolant Engine coolant
Engine coolant
Engine coolant
If the temperature in your area drops below
freezing, there is the danger that the coolant inthe engine or radiator could freeze and causesevere damage to the engine and/or radiator. Be sure to add a sufficient amount of antifreeze
to the coolant to prevent it from freezing.
The engine coolant mixture used at the factory
is intended to be left in the cooling system andprovides protection against freezing for tem-perature as low as approximately -30°C (-20°F).The concentration should be checked beforethe start of cold weather and anti-freeze addedto the system if necessary
D180C01P-GATBattery
Battery Battery
Battery
Battery
The capacity of the battery is reduced at low
temperatutes.
This is an inevitable result of its chemical and
physical properties. This is why a very coldbattery, particularly one that is not fully charged

IN CASE OF EMERGENCY
IN CASE OF EMERGENCY IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
IN CASE OF EMERGENCY
4-3
GS40090A
Notch of handle
Pressure piston
Then fit the handle into the pressure piston, and
align the groove of the handle with the notch of the holder.
Move the jack handle up and down to raise the
piston.
Using a jack handle, turn the relief valve coun-
terclockwise slowly to lower the piston.
Press the piston down all the way, and turn the
relief valve clockwise as far as possible.
GS40100A
CAUTION:
CAUTION: CAUTION:
CAUTION:
CAUTION:
(1)(1)
(1)(1)
(1)
Use only the jack included with the ve-
Use only the jack included with the ve- Use only the jack included with the ve-
Use only the jack included with the ve-
Use only the jack included with the ve-
hicle and use it only for changing a wheel.
hicle and use it only for changing a wheel. hicle and use it only for changing a wheel.
hicle and use it only for changing a wheel.
hicle and use it only for changing a wheel.
(2)(2)
(2)(2)
(2)
Position the jack on a hard level surface.
Position the jack on a hard level surface. Position the jack on a hard level surface.
Position the jack on a hard level surface.
Position the jack on a hard level surface.
(3)(3)
(3)(3)
(3)
If the relief valve is loosened by turning
If the relief valve is loosened by turning If the relief valve is loosened by turning
If the relief valve is loosened by turning
If the relief valve is loosened by turning
it 2 or more times in the counterclock-
it 2 or more times in the counterclock- it 2 or more times in the counterclock-
it 2 or more times in the counterclock-
it 2 or more times in the counterclock-
wise direction, the jack’s oil will leak and
wise direction, the jack’s oil will leak and wise direction, the jack’s oil will leak and
wise direction, the jack’s oil will leak and
wise direction, the jack’s oil will leak and
the jack cannot be used.
the jack cannot be used. the jack cannot be used.
the jack cannot be used.
the jack cannot be used.
(4)(4)
(4)(4)
(4)
This jack is hydraulic, and the ram is a
This jack is hydraulic, and the ram is a This jack is hydraulic, and the ram is a
This jack is hydraulic, and the ram is a
This jack is hydraulic, and the ram is a
two-stage type. When both rams are
two-stage type. When both rams are two-stage type. When both rams are
two-stage type. When both rams are
two-stage type. When both rams are
raised and the stop mark(Green paint)
raised and the stop mark(Green paint) raised and the stop mark(Green paint)
raised and the stop mark(Green paint)
raised and the stop mark(Green paint)
of the upper ram becomes visible, stop
of the upper ram becomes visible, stop of the upper ram becomes visible, stop
of the upper ram becomes visible, stop
of the upper ram becomes visible, stop
jacking immediately.
jacking immediately. jacking immediately.
jacking immediately.
jacking immediately.
Further extension of the ram may dam-
Further extension of the ram may dam- Further extension of the ram may dam-
Further extension of the ram may dam-
Further extension of the ram may dam-
age the jack.
age the jack. age the jack.
age the jack.
age the jack.
(5)(5)
(5)(5)
(5) When the jack is used, be sure that there
When the jack is used, be sure that there When the jack is used, be sure that there
When the jack is used, be sure that there
When the jack is used, be sure that there
is no one in or under the vehicle.
is no one in or under the vehicle. is no one in or under the vehicle.
is no one in or under the vehicle.
is no one in or under the vehicle. (6)(6)
(6)(6)
(6) When jacking up the vehicle, do so only
When jacking up the vehicle, do so only When jacking up the vehicle, do so only
When jacking up the vehicle, do so only
When jacking up the vehicle, do so only
until the tires are slightly lifted from the
until the tires are slightly lifted from the until the tires are slightly lifted from the
until the tires are slightly lifted from the
until the tires are slightly lifted from the
ground. It is dangerous to jack up the
ground. It is dangerous to jack up the ground. It is dangerous to jack up the
ground. It is dangerous to jack up the
ground. It is dangerous to jack up the
vehicle more than that much.
vehicle more than that much. vehicle more than that much.
vehicle more than that much.
vehicle more than that much.
(7)(7)
(7)(7)
(7) It is very dangerous if the jack somehow
It is very dangerous if the jack somehow It is very dangerous if the jack somehow
It is very dangerous if the jack somehow
It is very dangerous if the jack somehow
slips, so never leave the vehicle in the
slips, so never leave the vehicle in the slips, so never leave the vehicle in the
slips, so never leave the vehicle in the
slips, so never leave the vehicle in the
jacked-up position, and never shake the
jacked-up position, and never shake the jacked-up position, and never shake the
jacked-up position, and never shake the
jacked-up position, and never shake the
vehicle while it is raised.
vehicle while it is raised. vehicle while it is raised.
vehicle while it is raised.
vehicle while it is raised.
E040B01P-GAT To jack up vehicle on 4-wheel drive
To jack up vehicle on 4-wheel drive To jack up vehicle on 4-wheel drive
To jack up vehicle on 4-wheel drive
To jack up vehicle on 4-wheel drive
GS40110A
Do not crank the engine while jacking up the
vehicle.
The tire on the ground may turn and the vehicle
may roll off the jack.